RAB Lighting EZLED User manual

EZLED INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]
Locking
Bolt
SLIPFITTER MOUNTING
1. The sliptter mounting ts a 2 3/8” O.D. Tenon. Place the
sliptter over the Tenon and secure the xture with the
2 Set Screws on the side of the sliptter.
2. Remove 2 screws on side of Round Cover Plate.
Remove the Round Cover Plate and adjust the angle of
the xture.
3. Loosen the Locking Bolt and swivel xture to desired
angle.
4. Tighten the Locking Bolt and re-attach Round Cover
Plate.
Tenon
Set Screws
Round
Cover
Plate
Pivot Bolts
TRUNNION MOUNTING
CAUTION: UL and C-UL listed or CSA certied liquid
tight cord grip suitable for use with three conductor
type STW exible cord shall be used for connection to a
wet location outlet box provided by others.
To adjust the angle of the xture using the trunnion:
1. Loosen the Pivot Bolts & angle locking screw.
2. Adjust xture to desired angle.
3. Tighten Pivot Bolts & angle locking screw.
WIRING
Universal voltage drivers permits operation at 120V to
277VAC, 50 or 60 Hz.
1. Connect the BLACK xture lead to the (+) LINE supply
lead.
2. Connect the WHITE xture lead to the (-) COMMON
supply lead.
3. Connect the bare copper Ground wire from xture to
supply ground.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
Close Up
Plugs (4)
If desired, cover the screw holes with the provided Close
Up Plugs (4) on the back cover as shown above. Tap lightly
into place.

EZLED INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]
EZLED-IN-0113
CLEANING & MAINTENANCE
CAUTION: Be sure xture temperature is cool enough
to touch. Do not clean or maintain while xture is
energized.
1. Clean glass lens with non-abrasive glass cleaning
solution.
2. Do not open the xture to clean the LED. Do not touch
the LED.
Note: These instructions do not cover all details or variations in
equipment nor do they provide for every possible situation during
installation, operation or maintenance.
Pat Pending
ACCESSORIES
Chrome Wire Guard: GDEZLED78W
Poly Shield: GDEZLED78P
Lens & Door Replacement: LEZLED78 (bronze)
LEZLED78W (white)
GUARD OR SHIELD INSTALLATION
Wire Guard and Poly Shield mount with (4) #8-32
Stainless Steel Screws. Screws are provided with the
accessory. Guard and shield may be used together. See
gure 1 for Guard. See gure 2 for Shield
1. Line up guard or shield with existing pre-drilled holes in
frame as shown, tighten screws.
Stainless Steel
Screws (4)
Stainless Steel
Screws (4)
Figure 1
Figure 2
EZLED78 3Hx3V Cool EZLED78N 3H x 3V Neutral EZLED78Y 3H x 3V Warm
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2012 RAB LIGHTING Inc.
No
rthvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly [e-mail]
TROUBLESHOOTING
1. Check that the line voltage at the xture is correct. Refer
to wiring directions.
2. Is the xture grounded properly?
3. Is the photocell, if used, functioning properly?

EZLED BILEVEL INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]
TM
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2014 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly [e-mail]
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is
required for safety. This product must be installed in accordance with the applicable installation code by a person familiar with the
construction and operation of the product and the hazards involved.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
WIRING
1. Bi-level xtures have LED’s separated and wired as shown.
2. Each set has leads brought through the arm and labeled as shown below.
3. Use the sets for switching as needed in your application.
EZLED BL IN 0514
Center LED
Outside LED