Raidon SafeTANK GR5630-WSB3+ User manual

www.RAIDON.com.tw
Your Data Security Guardian
GR5630-WSB3+
User Manual
SafeTANK
v.1.0 (Oct, 2012)

www.RAIDON.com.tw
Your Data Security Guardian
Table of Contents
Chapter 1. Package Contents and Product Views
Chapter 2. Environmental Requirements
Chapter 3. Hardware Requirements and Precautions
Chapter 4. Hardware Installation
Chapter 5. Description of Front Panel Operation and LCD Information
Chapter 6. Replacement of Malfunctioning Drive and Data Rebuild Instructions
Chapter 7. System Temperature Overheat and Fan Failure Management
Chapter 8. Visual Status Indicator Definitions
Chapter 9. Frequently Asked Questions

www.RAIDON.com.tw
Your Data Security Guardian
Chapter 1 Package Contents and Product Views
Please make sure that the contents listed above are not damaged or missing. If you should find
damages or missing contents, please contact your supplier immediately.
Open the package and you should find the following :
GR5630-WSB3+
Item Qty.
GR5630-WSB3+
(with removable drive tray enclosed)
Firewire 800 (1394b) Cable
e-SATA Cable
USB 3.0 Cable
Accessories Kit
AC Power Cable
CD(GUI)
Quick Installation Guide
1
1
1
1
1
1
1
1
USB3.0
Alarm Mute
Hard drive status Indicator
Removable drive tray
Button for Tray Clamp
LCM display
UP button
DOWN button
ENTER button
ESC button
Power indicator
Alarm indicator
USB3.0 interface connection
e-SATA interface connection
FireWire 800 (1394b) interface connection
Mute button
Power Switch
Power socket
Cooling fan
Anti-theft cord slot
Drive position(1)
Drive position(2)
Drive position(3)
Drive position(4)
Storage Mode Definition
Independent mode ( JBOD ) : Four discrete storage capacities.
Speed mode ( Raid 0 ) : One big independent data storage with without data protection.
Safe mode ( Raid 1 ) : One independent data storage with data protection.
The secondary FireWire 800 (1394b) connection on the GR5630-WSB3+ is provided to connect and
extend to another FireWire 800 (1394b) device.
Front view Rear view
Enter Esc

www.RAIDON.com.tw
Your Data Security Guardian
Chapter 2 Operating Information
Chapter 3 Hardware Requirements and Precautions
Operating Temperature : 0 ∼40 ℃(32 ~ 104 ℉)
Storage Temperature : -10 ∼70 ℃(14 ~ 158 ℉)
Line Voltage : 100 ∼240V AC
1. Only one interface connection may be used at once per computer system.
2. RAID volume formation utilizes the capacity of whichever hard drive has the smallest and then
multiply that capacity by three for RAID 5, four for RAID 0, to form a large volume, therefore,
it is recommended to only install hard drives of the same brand and specification for all drive
position prior to use. Moreover, when you need to replace with a new hard drive, please be
sure to purchase one with the same specification, capacity and brand. If these conditions can’t
be met, select one that’s at least 20 GB greater in capacity.
3. The actual storage capacity of GR5630-WSB3+ recognized by the system may differ from the
total capacity stated on the hard drives once the drives have been formatted.
4. When connected to the computer system, it’s prohibited to remove, insert or swap the hard
drive while data transfer is being performed.
5. It’s prohibited to change the positioning of the drives once the initial installation has been
completed as the changes made to the drive positions may destroy the RAID formation.
6. If you discover that hard drive failure is taking place, go to Section 6 “Replacement of
Malfunctioning Drive and Data Rebuild Instructions” and follow the steps accordingly.
7. Whenever turning off or unplugging the GR5630-WSB3+ from your computer system becomes
necessary, always remember to safely remove it from your operating system first.
8. In RAID 5 mode, the system allows one single hard drive failure. If multiple drive failures occur
at once, it’s likely that all data stored in the system have been destroyed or lost. In RAID 0
mode, if one hard drive failure occurs, then all data maybe destroyed or lost. If this happens,
we recommend you to consult with a professional hard drive data recovery specialist to see if
your data may be recoverable.
9. It is highly recommended for users to back up important data contained within the
GR5630-WSB3+ unit on a regular basis or whenever the user feels necessary to a remote or a
separate storage device. RAIDON will not be responsible for any lost of data caused during the
use of the unit or the recovery of the data lost.

www.RAIDON.com.tw
Your Data Security Guardian
Chapter 4 Hardware Installation
Step 1 Open the package and take out the product making sure that all the enclosed contents
are not damaged or missing. Should you find damages or missing contents, please contact
your supplier immediately.
Step 2 Place the system on a stable surface. Ensure that it is well ventilated without blockage to
the vent and kept away from areas near water and damage prone areas.
Step 3 Press down the button for tray clamp to eject the removable drive tray latch and extract the
removable drive tray.
Step 4 Mount your hard drives onto the removable drive tray and secure it with the screws included
in the accessory kit to avoid any damage to the hard drive due to accidental movements.
Step 5 When the hard drive installation has been completed, insert the hard drive tray into the
system horizontally and secure the latch into place.

www.RAIDON.com.tw
Your Data Security Guardian
Step 6 Connect the AC power cable to the GR5630-WSB3+, and then plug the AC power to the
wall socket. Boot-up the unit.
Step 7 Set the storage mode using the LCD and buttons on the front (please refer to section 5 for
front panel and LCD information).
Step 8 Connect the cable to the PC and the GR5630-WSB3+ port.
Step 9 After boot-up, your operating system will automatically detect the storage capacity of your
hard drives. Please follow the operating system instructions to configure and format your
drives. The formatted drives can be configured for the RAID setup.
Chapter 5 Description of Front Panel Operation
and LCD Information
Level 0
External 4BAY
HARDWARE
RAID
Quick Setup Create One RAID
Delete All RAID
Identify Disk
Show Disk Info
Identify RAID
Create RAID
Delete RAID
RAID Info
Change RAID Pwd
Rebuilding Priority
Standby Timer
System Info
Changhe Password
Logout From Menu
Alarm Control
Voltage Monitor < 3.3V / 5V / 12V >
< Temp. >
< Fan Speed /
Fan Level >
Temp. Monitor
Fan Monitor
Hardware Monitor
Select Disk
< Disk Info >
Select RAID
RAID 0 / RAID 5
Select RAID
< Password > for RAID Setup
Highest/High/Medium/Low/Lowest
< 99999min >
Firmware Version
< Password > for System Info
< Y or N >
Mute the Buzzer
Disk 1
Disk 2
Disk 3
Disk 4
Check Disk LED
Check Disk LED
Check Disk LED
Check Disk LED
RAID 0/ RAID 5 Select Disk
Disk Manager
RAID Manager
System Manager
Level 1 Level 2 Level 3 Level 4

www.RAIDON.com.tw
Your Data Security Guardian
Chapter 6 Replacement of Malfunctioning Drive
and Data Rebuild Instructions
When a front hard drive indicator has lit up red and the audio alarm sounds, this could mean the
indicated hard drive may be malfunctioning. If this occurs, you may press the mute button at the
rear of the system to shut off the audio alarm and power off the system immediately if in the
allowed operational state, and then re-power on the system to double check and see if in fact the
indicated hard drive has malfunctioned. If the problem persists, please turn off the system and
follow the directions below :
Step 1 Remove the drive tray containing the malfunctioned hard drive and disassemble the hard
drive from drive tray.
Step 2 Mount the new hard drive onto the tray and insert it back to the empty drive position of
the GR5630, then push the latch into place making sure it is secured and locked.
Step 3 In RAID 5 mode, when you turn the system on, the hard drive status indicator of the
replacement drive will interchangeably blink red and purple to inform that the data is
being rebuilt to the replacement drive. During data rebuild, you may operate the
GR5630-WSB3+ as normal. When the indicator stops, the data rebuild process has been
completed.
Chapter 7 System Temperature Overheat
and Fan Failure Management
If the alarm indicator has lit up red and the audio alarm sounds, this could mean that either a
system fan has stopped operating entirely or the system temperature has exceeded over the
default temperature of 60°C. When this occurs, you may press the mute button at the rear of
the system to shut off the audio alarm and power off the system immediately if in the allowed
operational state to let the system cool. Check and see if the overall operation environment is
well ventilated and make sure there are no blockages to the enclosed fan and then re-power on
the system to continue use. If the problem persists, please turn off the system and contact your
supplier or the RAIDON tech support for further assistance.

www.RAIDON.com.tw
Your Data Security Guardian
Chapter 8 Visual Status Indicator Definitions
Chapter 9 Frequently Asked Questions
Q1. Which drive format should I choose to format the hard drives in the GR5630-WSB3+?
A : It depends on the computer system you most often use. See the below suggestions:
1.Use NTFS format for Windows 2000/XP/Vista/Windows 7 system
2.Use HFS+ (Mac OS Extended) format for a Mac OS X system
3.Choose FAT32 format if you’ll use the GR5630 in both Windows and Mac environments
(the maximum size of one single file may not exceed 4 GB).
Q2. Why can’t my GR5630-WSB3+ reach the transfer performance speed of 200 MB/s via
e-SATA interface as stated on your website?
A : 1.Please first check if your PCI-E SATA host adapter would only support PCI-E (1X). This type
of host adapters cannot reach the transfer performance speed beyond 135MB/s.
2.The GR5630-WSB3+ will need to be set to the RAID 0 mode also.
States
Power on
No disk
Disk Fail
RAID Fail
Disk Idle
Format
Access
Fan Fail
Blue
Blue
Blue
Blue Blue
Blue
Blue
Source: Blue flash
Target: Blue and Purple
light on alternatively
1 long when
booting finished
Blue flash
Blue flash
Blue
Blue
Blue
Blue
Blue
Power LED Alarm LED
--------
-------- -------- --------
--------
--------
--------
--------
--------
--------
--------
--------
--------
--------
--------
Red
Red
Red
Red
HDD LED
buzzer
4 short
4 short
4 short
Blue flash => Blue
Front LED
Blue
Over Temp.
Rebuilding