Raidon InTANK HyBrid RunneR iH1010-2S-S2 User manual

InTANK Series
HyBrid RunneRiH1010-2S-S2
User Manual
v.1.0 (July, 2010)

Introduction
About this User Manual
Thank you for using the product of RAIDON Technology Inc..
This user manual will introduce the RAIDON iH1010-2S-S2 product. It is recommended that you read
this manual carefully before using the RAIDON iH1010-2S-S2 product. Although the information has
been veried before published, specications are subject to change without prior notice. Please refer to
www.RAIDON.com.tw or contact your sales representative for any product specication or update of
related information.
If you have any questions on RAIDON products or need the latest product information, user manual
or rmware, please contact us at [email protected] and we will get back to you as soon as
possible.
NOTE: RAIDON Technology Inc. only provides technical support and service to RAIDON direct customers. For end
users or non-direct customers, please contact your distributor for prompt and better responses. If your product
is not purchased directly from RAIDON, please do not contact us directly since you may not get any reply.
All the product information in this manual is the property of RAIDON Technology Inc. All rights reserved.

Index
Chapter 1 Product Introduction.................................................................. 4
1.1 Product Diagrams and Contents of Product Package.................... 4
1.2 LED Instructions.............................................................................. 4
1.3 Hardware Installation...................................................................... 5
1.4 Start-up of iH1010 and Drive Device.............................................. 6
1.5 Precautions before Usage.............................................................. 8
Chapter 2 HyBrid Function Introduction.................................................. 9
2.1 With Performance of SSD and Capacity of HDD............................ 9
2.2 Removable SSD Design................................................................. 10
2.3 Recover to New SSD...................................................................... 10
Chapter 3 GUI Function Introduction (Windows Only)....................... 12
3.1 System Status................................................................................. 12
3.2 System Setup.................................................................................. 12
3.3 Firmware Upgrade.......................................................................... 13
3.4 E-mail Notify.................................................................................... 14
3.5 About.............................................................................................. 14

Chapter 1 Product Introduction
1.1 Product Diagrams and Contents of Product Package
Front View Rear View
1Lock Hole of 3.5” HDD 1 SATA Port
2LED of 3.5” HDD 2Function Mode
3 Power LED 3 Power Connector of Fan
4LED of 2.5” SSD 4Fan
5Lock Hole of 2.5” SSD
Function Mode
※ Please select the function mode with the jumper located at the back panel. There are three pins at
the back panel for function mode selection : HyBrid mode by setting the jumper on the left of the two
pins. Clear mode by setting the jumper on the right of the two pins.
After you open the outer package, make sure that the following items are contained in the
package:
Item Qty.
iH1010-2S-S2 Device 1
Quick Installation Guide 1
CD 1
Accessory Kit 1
Please make sure related accessories and product body are not missing or damaged. For any
questions, please contact local distributor or retailer from your purchase for further assistance.
1.2 LED Instruction
Status LED LED Status
Power on Power LED Blue / Lights On
Fan Failure (Stop Rotating) Power LED Purple / Lights On
Overheat (Over 55°C) Power LED Purple / Lights On
Accessing LED of 3.5” HDD / 2.5” SSD Purple & Blue / Blink Alternatively
Drive Failures or No HDD / SSD LED of 3.5” HDD / 2.5” SSD Blue & Red / Blink Alternatively
Data Backup Proceeding LED of 3.5” HDD / 2.5” SSD Purple & Red / Blink Alternatively (Target)
Purple / Lights On (Source)
4Product Introduction

1.3 Hardware Installation
1. Use the key from accessory kit to unlock front panel of 3.5” HDD / 2.5” SSD from HDD/SSD lock
holes, and open the panel to 90 degrees, perpendicular from the original position.
2. Install 3.5” HDD / 2.5” SSD properly into each dened drive slots and make sure HDD/ SSD are
correctly positioned before closing the front panels.
3. Set the function mode to “Clear Mode” and connect DC cable (SATA 15 Pin). Then power on iH1010
to create new partition and wait for 30 seconds, the partition will be ready when the LED of both SSD
and HDD blink in blue & red alternately, nally power off the iH1010.
4. Set the function mode to “Hybrid Mode” and Install device into one of the CD-ROM bays with screws
from the accessory kit, then properly connect DC cable and SATA cable from your system to the
device.
Product Introduction 5

5. Hardware Installation is completed.
※ For future SSD or HDD exchange, please open the front panel to 90 degrees, perpendicular to the
surface cover and withdraw the SSD/ HDD.
1.4 Start-up of iH1010 and Drive Device
1. Power on your system after hardware installation completed. Insert the product CD from the package
into your CD-ROM, and locate “HyBird GUI.exe” le from the CD then double click to execute GUI
program. After login to GUI, click on [System Setup] → [Initialize] → [Setting] to initial the drives.
Once the message “Auto partition completed” appears, please re-booting your computer.
※ The initialize setting is not necessary, when you already nished the partition via function mode.
6Product Introduction

2. After rebooting your system, please enter “Disk Management” and you should nd the newly added
drives.
3. Enter "Disk Management" and initialize the newly added drives, then proceed with “format" to each
drives with desired le system type, and device will be ready to use upon the format is completed.
Product Introduction 7

4. When nished, it appears two disc volumes as (1) Disk-G : with the performance of SSD & backup
functions, (2) Disc-H : the extended capacity of SATA HDD.
From an O.S. installation, we suggest utilizing Disk-G for the O.S. installation and Disk-H for data
storage to get the best performance of HyBrid RunneR iH1010.
※ Drive letters may vary from different system congurations, please refer to your system settings
accordingly.
1.5 Precautions Before Usage
1. Please make sure the capacity of HDD is bigger than SSD’s.
2. Before exchanging or replacing the existing SSD/HDD, please conrm the capacity of the
replacement drive is equivalent or bigger than the original drive.
3. For normal operation of iH1010, please do not manually modify the auto-partitioned volumes from
iH1010.
8Product Introduction

Chapter 2 HyBrid Function Introduction
2.1 With Performance of SSD and Capacity of HDD
NOTE : 1. Please make sure the capacity of HDD is bigger than SSD.
2. How to calculate the capacity of disk volumes?
Eg:
Capacity of SSD: 80GB
Capacity of HDD: 120GB
Capacity of Disk-A: 80GB
Capacity of Disk-B: 120GB-80GB=40GB
HyBrid Function Introduction 9

2.2 Removable SSD Design
SSD can be easily removed and used as a portable storage with an external enclosure. Upon nish,
insert the same SSD back into the iH1010 which will automatically backup existing data from SSD and
overwrite to the backup sector of HDD.
This backup function will only takes effect after rebooting iH1010 when SSD is inserted.
2.3 Recover to New SSD
In the event of SSD failure, simply replace with a new SSD to iH1010 to recover from the backup sector
of HDD to a new SSD via GUI.
1. In the event of SSD failure, GUI will indicate with light gray text as the diagram below. At this time,
data access will proceed through HDD, in order to retain the performance of SSD, please replace
failed SSD with a new one.
2. After replacing with a new SSD, GUI will detect it and also show the message “Unmatched SSD is
inserted” as the diagram below.
10 HyBrid Function Introduction