RATH MICROTECH SMARTPHONE II Installation manual

To begin programming
To program CALL TRACKER
To Program numbers
To program the timer
To end programming
1. Plug line cord into standard telephone line.
2. Connect transformer to 110V AC.
3. Press and release. Will get deedoodee tone.
1. Press Speak message. Press at end of message.
Will get deedoodee tone. Message maximum length is 18 seconds.
2. Press key to play back the message. Will
get deedoodee tone when done.
If you want to disable press then
Will get deedoodee tone. No message will play
during the phone operation
1. Program first number by pressing followed by the number to
be dialed and then to store the number.
Will get deedoodee tone.
2. Program the second number by pressing followed by the number
to be dialed and then to store the number.
Will get deedoodee tone.
3. If you wish to disable automatic dialing of second number, press
followed by
1. Press followed by again and the time (1-999 miinutes).
Then press to store the time-out. Will get deedoodee tone.
1. Hold until warble sounds, then release. If you get three
low beeps, the key was not held long enough.
Press and hold again until the warble sound.
2. telephone numbers and timer can be independently
reprogrammed at any time.
START
START. STOP
PAUSE CALL TRACKER
NOTE: CALL TRACKER, START STOP.
CALL TRACKER
SET
M1
SET
M2
SET M2.
SET SET
SET
STOP STOP
CALL TRACKER,
SMARTPHONE II
SIMPLIFIED PROGRAMMING INSTRUCTIONS
POT
D14
GREEN
LED
PHONE LINE
CONNECTOR
TO
TELEPHONE
LINE
TO
110V
AC
SOURCE
6 POSITION
TERMINAL BLOCK
J2
A/C TRANSFORMER
RATH MICROTECH
SUSSEX, WI
1
4
7
0M1 M2
89
56
START
STOP
PAUSE
2 3
SET
FAX 12
RATHMICROTECH
Technology of the future, available today!
NOTE:
SMARTPHONE II can
be programmed
without connection
to 110V AC or the
telephone line when
back-up battery is
fully charged.

RATHMICROTECH
Technology of the future, available today!
Remote Programming
FAX 14
Step 1 REMOTE PROGRAMMING SEQUENCE
A. SMARTPHONE II Standard Remote Programming
B. SMARTPHONE II Consolidator Mode Remote Programming
A) Single Phone
B) Changing all phones in a group
1. Call number of phone or phones.
2. After you get the simulated ring, press the # key, will hear long
dedodedodedo tone.
3. Key in the security code (4 digits). Will hear
deedoodeedoo tone. Wrong security code will terminate call.
4. Press 9*0. Will hear tone. All phones will be ready to program.
See Table A for programming menu.
5. Press 9*# to end programming.
1. Call number of phone or phones.
2. After you get the simulated ring, press the # key. Will hear long
dedodedodedo tone.
3. Key in the security code (4 digits). Will hear deedoodeedoo tone.
Wrong security code will terminate call.
4. Changing a single phone or all in group.
1. After security code, press 9*1. Will hear deedoodee tone.
This will make phone with ID 1 ready to program.
2. See Table A for programming menu.
3. Press 9*2. Will hear deedoodee tone. You are now ready to
program phone with ID 2. See Table A.
4. Continue this until you have programmed all in the group.
5. Press 9*# to end programming.
1. After security code, press 9*0. This will make all phones
ready to program.
2. See Table A for programming menu.
3. Press 9*# to end programming.
1 # (Enter phone number M1, for pauses) # Deedoodee
1 Phone number M1 is played back in beeps Deedoodee
2 # (Enter phone number M2, for pauses) # Deedoodee
2 Phone number M2 is played back in beeps Deedoodee
3 # (Enter timeout minutes, last three digits) # Deedoodee
3 Timeout minutes played back in beeps Deedoodee
4 # Record Message # to stop Deedoodee
4 Message is played back Deedoodee
9 # Will terminate call
Factory set at 15 minutes
TABLE A