Real Good Toys QuickBuild Firehouse User manual

Parts List (listed in order of use):
(Measurements may vary slightly)
Panels and Assembled sections:
(1) Base Floor (nished only on 1 side)
(1) Right Side Assembly
(1) Back Wall - 15 3/4”W
(1) Front Assembly - 15 3/4”W
(1) Middle Floor
(1) Roof Top Assembly
(2) Front & Rear Side Walls - 3 1/8”W
(1) Top Front Assembly
(1) Front Step
Small Parts Bag:
(12) Screws
Trim:
(2) Mitered Roof Top Edge Trim
3 3/8” (top edge of Rear Walls)
(2) Corners - (3 notches )
(ts inside edge of the Rear Walls)
(2) Front Corners
(1 bottom notch - ts over entry ramp)
(2) Corners - (ts the Back corners)
(2) Flat Trim - 2 1/4”
(upper edge of Rear Walls)
(2) Flat Trim - 15 3/4”
(upper edge of Front and Back)
(2) Mitered Roof Top Edge Trim - 17”
(1) Fire Pole
(1) Coat Rack
(attach to the inside of the Back Wall 6” above the oor)
Tips for building the perfect dollhouse:
Congratulations on your purchase of a Real Good Toys’ QuickBuildTM
dollhouse. Your QuickBuildTM kit has been precision made with me-
ticulous care by our craftspeople using cabinet grade materials and
requires only ordinary white glue to quickly and easily build a sturdy
dollhouse you will be proud of for many years to come.
This dollhouse will last for years, even generations, if proper care and
attention is given during assembly. Take your time and be sure to read
the instructions completely before you proceed.
Check all parts and packs against the parts list before beginning con-
struction to identify the parts and to make sure you have everything. If
you need replacement parts be sure to include the exact name and mea-
surements taken directly from the parts list.
Assembly Notes:
A large, clutter-free, well lighted work area is most helpful during as-
sembly, and a at work surface is very important.
Supplies you will need:
Phillips Screwdriver
White glue
Masking tape
All the parts should be attached with glue. Use generous
amounts of glue and always wipe off excess glue immediately. Use
masking tape, if necessary, to hold parts together while the glue dries.
Read the instructions carefully, look at each of the illustrations. With the
parts in your hands, think the assembly through before you proceed.
Always test t (without glue) parts before nal assembly.
Make sure everything is straight and at as the glue dries... That’s
the shape that will be permanent.
Real Good Toys
10 Quarry Hill * Barre, Vermont 05641
Customer Service: 802-479-2217
#00080 QuickBuildTM Firehouse Instructions

1. Attach the Base Floor to the Right
Side. (use a weight to hold the Floor
Seam together while the glue dries.) 2. Attach the Back to the
Right Side. Screw through
the pre-drilled holes at the
top corner of the Back and
the bottom corner of the
Right Side.
3. Attach the Front to the Right Side. Screw through the pre-drilled
holes at the top corner of the Front and the bottom corner of the Right
4. Attach the Middle Floor.Page 2

6. Attach the Front and Rear Side Walls. Make sure the pre-drilled holes line
up well. These walls should be identical. But, if the holes do not line up, switch
7. Attach the Mitered Roof Top Edge
Trim (17”) and the Top Front in the
8. Place glue in the hole on the base oor and on the top of the Fire Pole
and carefully ex the Fire Pole into the pre-drilled holes in the oor and Page 3
5. Attach the Roof Top. Do not over tighten the screws, or the Roof
Top Strip may split. If this happens, remove the screws and attach
with glue and tape only. This will not sacrice the quality of this
Slot
Roof Top Edge Trim

10. Attach the (2) Notched Corners to the inside edges (1 left & 1 right), at-
tach (2) Corners to the outside edges and attach the (2) 2 1/4” Flat Trim to the
upper edges of the Front & Rear Side Walls between the Corners.
11. Attach a Corner to the rear edge, a 17” Mitered Roof Top Edge Trim to
the top edge, and a 15 3/4” Flat Trim to the upper edge of the Back Wall (be-
tween the Corners).
12. Attach the remaining (2) Corners to the Front Walls.
13. Attach the Front Step below the Front Door.
14. Attach the Coat Rack to the inside of the Back Wall approx.
6” above the oor.
Page 4 Congratulations! You’re project is complete.
9. Attach the Mitered Roof Top Edge Trim (17”) and the (2) 3
3/8” Mitered Roof Top Edge Trim (1 left & 1 right) to the top
edges of the Front & Rear SideWalls.
Corner bottom notch
ts over entry ramp