Real Good Toys QuickBuild User manual

#00072 Colonial Instructions
Parts List:
(1) Base Floor (nished only on 1 side)
(1) 2nd Floor (stair hole)
(1) 3rd Floor
(1) Rear Foundation
(1) Left Side Panel
(1) Right Side Panel
(1) Front Panel
(1) 1st Floor Divider
(1) 2nd Floor Divider
(2) Attic Dividers
(1) Front Roof
(1) Rear Roof
(1) Assembled Staircase
(1) Assembled Short Landing Rail
(1) Assembled Long Landing Rail
(1) Left Rear Eave Trim
(1) Right Rear Eave Trim
(1) Left Front Eave Trim
(1) Right Front Eave Trim
(1) Chimney
(1) Assembled Front Steps
(4) Roof Ridge Strips
(1) Left Front Corner – 19 15/32”
(1) Right Front Corner – 19 15/32”
(1) Left Rear Corner – 20”
(1) Right Rear Corner – 20”
Small Parts Bag:
(2) Peak Gingerbread Trim (triangular)
(4) Dowels
(2) Long Screws
(4) Short Screws
Tips for building the perfect dollhouse:
Congratulations on your purchase of a Real Good Toys QuickBuildTM
dollhouse. Your QuickBuildTM kit has been precision made with
meticulous care by our craftspeople using cabinet grade materials and
requires only ordinary white glue to quickly and easily build a sturdy
dollhouse you will be proud of for many years to come.
This dollhouse will last for years, even generations, if proper care and
attention is given during assembly. Take your time and be sure to read
the instructions completely before you proceed.
Check all parts and packs against the parts list before beginning con-
struction to identify the parts and to make sure you have everything.
If you need replacement parts be sure to include the exact name and
measurements taken directly from the parts list.
Assembly Notes:
A large, clutter-free, well lighted work area is most helpful during as-
sembly, and a at work surface is very important.
Supplies you will need:
Phillips Screwdriver
White glue
Masking tape
All the parts should be attached with glue. Use generous
amounts of glue and always wipe off excess glue immediately. Use
masking tape, if necessary, to hold parts together while the glue dries.
Read the instructions carefully, look at each of the illustrations. With
the parts in your hands, think the assembly through before you pro-
ceed.
Always test t (no glue) parts before nal assembly.
Make sure everything is straight and at as the glue dries... That’s
the shape that will be permanent.
Real Good Toys
10 Quarry Hill * Barre, Vermont 05641
Customer Service: 802-479-2217

1. Attach the Left Side Panel to
the Front Panel using (1) dowel.
(Use the wallpaper patterns to
identify the left and right side
ASSEMBLY INSTRUCTIONS
2. Attach the Right
Side Panel to the
Front Panel using (1)
3. Attach the Rear Foundation to
the Side Panels and insert (2)
dowels. 4. Attach the Base Floor (the
groove goes towards the Front
5. Set the 1st Floor Divider in the
groove, making sure the wall-
paper matches on each side.
(note the notches on divider)
6. Set the 2nd Floor in
place (the groove goes
towards the Front
7. Adjust the 1st Floor Divider
to set properly in the 2nd Floor
groove.
8. Set the 2nd Floor Divider
in place, making sure the
wallpaper matches on each
side.
Page 2
Dowel
Dowel
Dowel Groove
Notch-
Groove
Notch-

Page 3
9. Set the 3rd Floor in place, adjust the 2nd Floor Divider
to t properly in the ceiling groove of the 3rd Floor. (Be
careful when inserting the 3rd Floor into the Front Panel
10. Set the 2 Attic Dividers in
place, make sure the wallpa-
per matches on both sides.
12. Attach the Rear Roof, make sure the Attic Dividers are set properly in the top and
bottom notches. Use (2) long screws through the peak of the Side Panels into the
peak of the Rear Roof support. Use (2) short screws in the rear side roof.
Groove
Short screw
Long screw
11. Set the Front Roof in
place and attach with (2)
short screws.
Short screw

Page 4
17. Attach the Assembled Short Landing Rails to
the Assembled Long Landing Rails inserting
the pegs in the pre-drilled holes, then glue
the rail assembly to the oor around the stair
14. Attach the (4) Roof Ridge
Strips to form the peak.
16. Attach the Assembled
Staircase - apply glue to
the side of the staircase
where it meets the wall
and the edge of the stair
hole.
15. Attach the Side Panel trims in this
order: 1st the Peak Gingerbread
Trim to cover the top screw hole,
then the Rear & Front Eave Trim
which cover the other screw holes
and then the Rear & Front Corners.
13. Attach the Chimney
to the Front Roof. Use
(2) stained Roof Ridge
strips to center the
chimney on the roof.
18. Attach the Assem-
bled Front Steps.
Congratulations!
20”
8 5/16”8 15/16”
19 15/32”