RealFlame 8805700 User manual

Instruction Manual

!
!
Rev. 04/30/07
Using your Log Set
- Log Set is designed for use in your existing indoor fireplace.
- Follow all instructions included with gel fuel before use.
- Before using Gel Conversion Log Set make sure you have read and understand the step-by-step instructions.
- During the inital burn you may experince a slight odor. This odor is temporary and will be absent on following burns.
Instructions and warnings for use.
Welcome to the Real Flame® family of gel fuel products. If you have any questions
please call customer service at 1-800-654-1704 or log on to www.REALFLAME.com.
WARNINGS
!!!
NOTICE: Buyer assumes all responsibility for safety and use that is not
in accordance with instructions and warnings.
1. Log set is designed to be used with Real Flame gel fuel only. Do not use with any other gel fuel or any other flammable
liquid or gel.
2. Read entire label and instructions before using Real Flame gel fuel.
3. Never leave a burning fire unattended, especially around children or pets.
4. When burning in an existing fireplace, be sure that the material surrounding the logs is non-combustible and it is clear
and free of all flammable materials.
5. Firebox must be brick, cement, steel or other non-flammable material because there will be a real fire inside.
6. Never touch logs or grate during or after burning gel fuel. Logs and grate will be extremely HOT. Allow logs, grate and gel fuel
cans to cool for 60 minutes before touching.
7. Do not burn more than three cans of fuel at once.
8. Keep away from children and pets. Log set is not to be operated by children.
9. Make sure log set and gel fuel are burned on a flat and level surface.
10. Do not alter log set in any matter.
11. Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this product.
12. Do not wear flammable or loose clothing when operating the outdoor gel log set.
13. Do not attempt to move or store the log set until 60 min after gel fuel cans have been extinguished.
14. Do not lean over log set when lighting or when in use.
15. Do not burn gel fuel outside designated burn areas on the metal plate.
16. In case of an emergency use a CO2 extinguisher to extinguish the fire.
17. Death, serious injury or damage to property may occur if the above is not followed exactly.
18. If for any reason you cannot follow these warnings please call us at 1-800-654-1704.
STOP!
If parts are missing or damaged, call 1-800-654-1704 for assistance
®
®

Rev 4/26/07
Before starting assembly, review
parts list making sure you have all the
pieces in good condition. If there are
any damaged or missing parts please
call customer service at
1-800-654-1704.
Before using fireplace read and
understand all instructions and safety
precautions included with this
7
8
Step One
Figure 1
With Grate (7) set on flat surface locate
Lift Assembly (8). Using the four holes
on the back of the Grate and 1" bolts,
attach the Lift Assembly with handle as
shown in figure 1.
Figure 1
2609 Instructions and warnings for use
Parts List
Number Description Part Number Quantity
1 Left Log 2609-R A 1
2 Middle Left Log 2609-R B 1
3 Middle Right Log 2609-R C 1
4 Right Log 2609-R D 1
5 Front Log 2609-R E 1
6 Rear Log 2609-R F 1
7 Grate 2609-R G 1
8 Lift Assembly 2609-R H 1
9 Lava Rock 4090 1 Bag
10 1” Phillips Head Bolt 9742 12

Step Three
Figure 3
Locate the Left Log (1) with the curve
of the log facing inward towards the
center. Attach log to metal brace with
two 1" bolts.
NOTE: Use caution not to over
tighten bolts.
1
Step Two
Figure 2
Raise handle on lift assembly to the
open position.
Place Front Log (5) and Rear Log (6)
as shown in figure 2
Figure 2
Figure 3
Rev. 4/26/07
2609 Instructions and warnings for use

Rev. 4/30/07
Step Four
Figure 4
Repeat step three with the remaining three
logs. Use figure 4 as reference for
placing the logs.
After all logs have been fastened to Lift
Assembly slowly lower lift arm. If the
top four logs don't rest on Front Log (5)
you may need to adjust the position of the
Rear Log (6) left or right.
Place assembled unit in your existing
fireplace.Add decorative lava rock around
the base of your fireplace.
Step Five
Figure 5
Using your Convert to Gel Log Set
With assembled unit in fireplace, raise lift assembly.
Place three cans of REAL FLAME gel fuel in fuel
tray located in the middle of the grate. With an
extended lighter or long match light gel fuel.
Carefully lower lift handle.
During the initial burn you may experience a slight
odor. This odor is temporary and will be absent on
following burns.
Figure 4
Figure 5
2609 Instructions and warnings for use