RealFlame 7800-M - Metal Products Mahogany Finish Carolina Real Flame Gel... User manual

Fireplace Model #7800
Instruction Manual
®

Rev. 06/04/07
Using your Fireplace
- Follow all instructions included with gel fuel before use.
- Before using Fireplace make sure you have read and understand the step-by-step instructions.
- During the initial burn you may experience a slight odor. This odor is temporary and will be absent on following burns.
Instructions and warnings for use
Welcome to the Real Flame® family of gel fuel products. If you have any questions
please call customer service at 1-800-654-1704 or log on to www.REALFLAME.com.
WARNINGS !!
NOTICE: Buyer assumes all responsibility for safety and use that is not
in accordance with instructions and warnings.
1. Fireplace is designed to be used with Real Flame®gel fuel only. Do not use with any other gel fuel or any other flammable
liquid or gel.
2. Read entire label and instructions before using Real Flame gel fuel.
3. Make sure fireplace is set on a flat, level and stable surface. Keep fireplace stable at all times.
4. Make sure fireplace and gel fuel are burned on a flat and level surface.
5. Never leave a burning fire unattended, especially around children or pets.
6. Fireplace is not to be operated by children. Keep away from children and pets.
7. Exercise the same precautions as you would with any open fire.
8. When in use some surfaces will be hot, use caution.
9. Never touch logs, gel fuel cans or any other metal surfaces during or immediately after burning gel fuel. They will be extremely
 HOT. Allow them to cool for 60 minutes before touching.
10. Do not burn more than three cans of fuel at once.
11. Do not place more than 15 lbs. of weight on the top of the fireplace at anytime.
12. Do not alter fireplace, metal firebox or log set in any manner.
13. Keep fireplace and gel fuel cans away from flammable materials at all times.
14. Do not store or use gasoline or any other flammable vapors, liquids, or materials in the vicinity of fireplace and gel fuel.
15. Do not wear flammable or loose clothing when operating the fireplace.
16. Do not move fireplace while in use. Do not attempt to move or store the fireplace until 60 minutes after gel fuel cans have
been extinguished.
17. Do not burn trash, paper, or wood in the fireplace. Burn only Real Flame®gel fuel in the fireplace.
18. Do not burn gel fuel outside designated burn areas on the metal grate.
19. Do not put fireplace in an area with lots of traffic, such as a hallway or entryway.
20. In case of an emergency use a CO2 extinguisher to extinguish the fire.
21. Death, serious injury or damage to property may occur if the warnings above are not followed.
22. If for any reason you cannot follow these warnings please call us at 1-800-654-1704.
®
®
STOP!
If parts are missing or damaged, call 1-800-654-1704 for assistance

Figure 1
Step One
Figure 1
- Insert tongue on Panel #3 into groove in Panel #5.
Be sure that bottom edges are flush and that direction
arrows on labels point in the same direction.
- Fasten with screws through m ounting blocks on
Panel #3 into pre-drilled holes in Panel #5.
- Repeat Step One using Panels #2 and #4.
Parts List
Panel#
1
2
3
4
5
6
7
8
Description
Base
Left Side Panel
Right Side Panel
Left Trim Panel
Right Trim Panel
Upper Surround
Center Panel
Mantel Top
Part Number
7801
7802
7803
7804
7805
7806
7807
7808
9713
1075
Quantity
1
1
1
1
1
1
1
1
Bag
2
Not Shown
1" Screws
Firebox Clips
Rev. 042006
Tips For Assembly
Before assembly, locate instructions and
hardware. Take out all parts and compare them
to the photograph and the assembly
illustrations. Be sure you have all parts
identified.
Check for screws that are wrapped in the
packaging to be sure you don't discard them.
You may have extra screws.
A helping hand is always good. Assemble
fireplace with an adult assistant if possible.
The cement log is heavy. Put the fireplace in
the desired location before inserting cement
log.
Use caution not to over tighten screws.
3
5
7800 Carolina Instructions

Step Two
Figure 2
- Position Base (#1), onto a flat and level surface,
so that you are facing the back edge.
- Insert tab on Panel #3 into opening in Base as shown.
Position Panel #5 against mounting block so that hole in
mounting block is over pre-drilled hole in Panel.
- Attach panels by screwing through holes in tab on
Panel #3 into pre-drilled holes in Base. Also, insert
screw through hole mounting block and screw into
pre-drilled hole in Panel #5.
- Repeat Step Two with Panels #2 & #4.
Step Three
Figure 3
- Position Panel #6 so that the lowest screw hole is
over the lowest of the pre-drilled holes in Panels #4
& #5. Be sure that holes closest to edge are facing up.
- Attach Panel #6 by screwing through holes in
mounting block into pre-drilled holes in Panels #4 & #5.
- Note: Slight inward pressure on sides may be
required to get holes to line up and to eliminate gaps.
- From the front, position Panel #7 so that top screw
hole in Panels #4 & #5 is over top pre-drilled hole in
Panel #7.
- Attach Panel #7 byinserting screws through holes in
Panels #4 & #5 and screwing into pre-drilled holes
in Panel #7.
Figure 2
Figure 3
3
5
4
2
1
7
6
Rev. 042006

Step Four
Figure 4
- Position Panel #8 so that the trim is on the outside
of the unit.
- Push Panel #8 as far back as possible so that the
back edge of Panel #8 lines up with the back edges
of sides.
- Attach Panel #8 by inserting screws through the
holes in the tops of Panels #2, 3, and 7 and by
screwing into pre-drilled tholes in Panel #8.
Figure 4
8
You are now ready for the firebox
installation. Please refer to the instructions
that are included with your firebox.
Rev. 042006