Rear view safety RVS-577FW User manual

Reverse With Condence ™ 1
Wireless Safety Camera System for Forklifts
with 5" Dual Screen Display
RVS-577FW
Instruction Manual

Rear View Safety
2
Introduction.............................. 03
SafetyInformation.............................. 04-06
BeforeBeginningInstallation ....................... 07-08
SystemFeatures............................. . . . 09
MonitorIntroduction.............................10-11
RemoteIntroduction...............................12
Triggers . . . . . ................. . . . . . . . 13-14
Menu.......................... . . . . 15-19
Pairing.......................... . . . . . 20
MonitorSpecications.. ...........................21
CameraSpecications.. ...........................22
Troubleshooting.................................23
Warranty....................................24
Disclaimer....................................25
TABLE OF CONTENTS

Reverse With Condence ™ 3
NOTE! Please read all of the installation instructions
carefully before installing the product. Improper
installation will void manufacturer’s warranty.
Congratulations on purchasing a Safety
Camera System!
With this manual you will be able to properly install and
operate the unit.
This system is intended to be installed as a
supplement aid to your standard rear view mirror that already exists
in your vehicle. The system should not be used as a substitute for the
standard rear view mirror or for any other mirror that exists in your
vehicle.
In some jurisdictions, it is unlawful for a person to drive a
motor vehicle equipped with aTV viewer or screen located forward of
the back of the driver’s seat or in any location that is visible, directly
or indirectly, to the driver while operating the vehicle.
INTRODUCTION

Rear View Safety
4
Please read the entire manual and follow the instructions and
warnings carefully. Failure to do so can cause serious damage and/or
injury, including loss of life. Be sure to obey all applicable local
trac and motor vehicle regulations as it pertains to this product.
Improper installation will void manufacturer’s warranty.
•The system is designed to help the
driver safely detect people and/or
objects helping to avoid damage
or injury. However, you the driv-
er, must use it properly. Use of this
system is not a substitute for safe,
proper or legal driving.
• Never back up while looking at the
monitor alone. You should always
check behind and around the vehi-
cle when backing up, in the same
way as you would if the vehicle did
not have the system. If you back up
while looking only at the monitor,
you may cause damage or injury.
Always back up slowly.
•The system is not intended for use
during extensive back-up maneu-
vers or backing into cross trac or
pedestrian walkways.
•Please, always remember, the area
displayed by the system is limited.
It does not display the entire pan-
orama that is behind you.
USAGE:
SAFETY INFORMATION

Reverse With Condence ™ 5
•Electric shock or product
malfunction may occur if this
product is installed
incorrectly.
• Use this product within
the voltage range specied. Failure
to do so can cause
electronic shock or product
malfunction.
•Take special care when
cleaning the monitor.
•Make sure to rmly ax the prod-
uct before use.
• If smoke or a burning smell
is detected, disconnect the
system immediately.
•Where the power cable may touch
a metal case, cover the cable with
friction tape. A short circuit
or disconnected wire may cause a
re.
• While installing the Rear View
System be careful with the wire
positioning in order to avoid wire
damage.
•The RearView System should only
be used when the vehicle is in
reverse.
• Do not watch movies or
operate the monitor while driving;
as it may cause an
accident.
• Do not install the monitor
where it may obstruct drivers
view or obstruct an air bag
device.
• Dropping the unit may cause
possible mechanical failure.
INSTALLATION:
SAFETY INFORMATION

Rear View Safety
6
If you have questions about this product, contact:
Rear View Safety
1797 Atlantic Avenue
Brooklyn, NY 11233
Tel: [phone]
IN NO EVENT SHALL SELLER OR MANUFACTURER BE
LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF
ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM
ANY DEFECTIVE PRODUCT ORTHE USE OF ANY PRODUCT.
SAFETY INFORMATION

Reverse With Condence ™ 7
Beforedrilling pleasecheckthatno cable or wiring ison the otherside
of the wall. Please clamp all wires securely to reduce the possibility
of them being damaged while vehicle is in use. Keep all cables away
from hot/moving parts and electrical noisy components.
We recommend doing a benchmark test before installation
to insure that all components are working properly.
Step 1: Choose the monitor and camera locations.
Step 2: Install all cables in vehicle, when necessary a 0.8 (20mm)
hole should be drilled for passing camera cable through vehicles
walls. Install split grommets where applicable.
Step 3: Once all cables and wiring have been properly routed, perform
a system function test by temporarily connecting the system.
BEFORE YOU BEGIN

Rear View Safety
8
BEFORE YOU BEGIN
1. This monitor is high voltage. Only professionals should open the
monitor's case.
2. Do not watch the video while driving unless you are monitoring the
rear view camera display.
Warning!

Reverse With Condence ™ 9
SYSTEM FEATURES
• Dual screen display - Can view 2 cameras simultaneously
• Normal/Mirror/Flip/Mir-Flip viewing modes
• Split/Auto-scan/Single display modes
• Instant Pair - Pair system without leaving your seat
• Magnetic camera - Simple installation
• Remote control
• 4 video inputs - Connect up to 3 additional cameras
• Multiple video formats: PAL/NTSC
• Wide voltage input: 10 - 32V
• Wireless/Magnetic/Waterproof camera
• Automatic trigger switch
System Features
In The Box
1 x 2.4G Digital 5.6"Wireless Color LCD Monitor
1 xWireless, Magnetic andWaterproof Forklift Camera
1 xWirelessTransmitter
1 xWireless Antenna
1 x Monitor Mount
1 x Sunshade
1 x U-Bracket Kit
2 x Mounting Pads
1 x Remote
1 x Power ConnectionWire

Rear View Safety
10
MONITOR INTRODUCTION

Reverse With Condence ™ 11
MONITOR INTRODUCTION
Monitor Introduction
1. Power indicator/On switch
2.Toggle volume up
3.Toggle volume down
4. Enter menu item/save user settings
5. Enter menu
6.Toggle channels
7. Speaker
8. U-Bracket screw position
9. Mounting attachment
Remote Introduction

Rear View Safety
12
REMOTE INTRODUCTION
1. Mute/Unmute
2. Enter menu/save settings
3.Toggle volume down
4. Jump Key - Jump to specied display mode
5. Instant pair
6.Turn monitor on/o
7.Toggle volume up
8. Enter menu
9.Toggle MIR/Flip display modes
10.Toggle PAL/NTSC
Remote Introduction
Basic Wiring
• Red wire to positive DC/10-32V power supply
• Black wire to ground
• Brown wire to reverse power
• White wire to left turn signal
• Blue wire to right turn signal
• Green/yellow wire to other positive power supply

Reverse With Condence ™ 13
TRIGGERS
Triggers
When green trigger wire is activated,
camera switches to CAM1
When white trigger wire is activated,
camera switches to CAM2
(left side camera)
When white trigger wire is activated,
camera switches to CAM3
(right side camera)
When brown trigger wire (reversing)
is activated, camera switches to
CAM4 (backup camera)
This also displays gridlines

Rear View Safety
14
TRIGGERS
When yellow trigger wire is activated,
monitor switches to dual display.
Volume With Dual Display
Use volume toggle buttons to select the channel for audio out.

Reverse With Condence ™ 15
MENU
Menu Introduction
MENU is only allowed for operation under single image mode, not
dual display mode. Press MENU to display the following options and
settings: MODE/PICTURE/MIR-FLIP/AUTOSCAN/SYSTEM/PAIRING.
Mode
Press - or + to select MODE. Press to enter.
Press - or + to select SPLIT. Select OFF to exit SPLIT menu.
Split trigger is disabled when split mode is o.

Rear View Safety
16
MENU
Press - or + to select BRIGHTNESS/CONTRAST/HUE/VOLUME.
Press to enter. Press MENU to return to main menu.
Picture
Press - or + to select Picture. Press to enter.
Brightness/Contrast/Hue/Volume

Reverse With Condence ™ 17
MENU
Press - or + to select MIR-FLIP.
Press to enter. Press MENU to return to main menu.
Mir-Flip
Press - or + to select NORMAL / MIRROR / MIR-FLIP / FLIP.
Press MENU to return main menu.

Rear View Safety
18
MENU
AutoScan
Press - or + to select Autoscan. Press to enter.
Press - or + to select CAM1/CAM2/CAM3/CAM4/SCANTIME.
Press to enter. When the icon turns yellow, press - or + to select or
adjust. Press to exit. Press MENU to return to main menu.
No video will be displayed under AUTOSCAN mode if a channel is turned
OFF.
SCANTIME duration is 5-45 seconds.Toggle up/down in 5 second inter-
vals.

Reverse With Condence ™ 19
MENU
Press - or + to select SYSTEM. Press to enter.
System
Time: Press - or + to selectTIME. Press to enter. Press - or + to
adjust.
Color-Sys:Press-or+toselectCOLOR-SYS.Press toenter.Press
- or + to adjust.
Auto-Dim: Press - or + to select AUTO-DIM. Press to enter,
press - or + to select ON/OFF.When setting is ON, the backlighting
automatically adjusts depending on the enviorment.
Electronic Distance Label (Distance Gridlines): Press - or + to select
ELECTRONIC DISTANCE LABEL. Press to enter. Press - or + to
turn distance gridlines ON/OFF. When it is on, distance gridlines
will be displayed on CAM4.

Rear View Safety
20
PAIRING
Pairing
Press - or + to select SYSTEM.
Press to enter. Press MENU to return to main menu.
Select the channel to pair, the monitor will display the message
“PAIRING START 50”.Turn camera on during countdown.The monitor
and cameras will synchronize themselves with each other after the
camera is powered for 5 seconds. The video will be displayed if in-
stant pairing is successful. Repeat the pairing if “No Signal”displays.
Instant Pair