red lion PAXCDL User manual

ORDERING INFORMATION
INSTALLING AN OPTION CARD
Caution: The option and main circuit cards contain static
sensitive components. Before handling the cards, discharge
static charges from your body by touching a grounded bare
metal object. Ideally, handle the cards at a static controlled
clean workstation. Also, only handle the cards by the edges. Dirt,
oil or other contaminants that may contact the cards can
adversely affect circuit operation.
Warning: Exposed line voltage exists on the circuit boards.
Remove all power to the meter AND load circuits before
accessing the unit.
1. Remove the main assembly from the rear of the case. Squeeze the finger
holds on the rear cover, or use a small screwdriver to depress the side
latches to release it from the case. It is not necessary to separate the rear
cover from the main circuit card.
2. Locate the option card connector for the type of option card to be
installed. Hold the unit by the rear connector, not the display board, when
installing an option card.
3. Install the option card by aligning the option card connector with the slot
bay in the rear cover. The cards are keyed by position with different main
board connector locations. Be sure the connector is fully engaged and the
tab on the option card rests in the alignment slot on the display board.
4. Slide the assembly back into the case. Be sure the rear cover latches fully
into the case.
5. Apply the option card label to the bottom side of the meter. Do not cover
the vents on the top surface of the meter. The surface of the case must
be clean for the label to adhere properly. Apply the label to the area
designated by the large case label.
DESCRIPTION
This bulletin serves as a guide for the installation, configuration and
operation of the PAX®Analog Output card. The analog output can be
configured for 0 to 20 mA, 4 to 20 mA or 0-10 VDC. Only one range can be
used at a time.
The PAX®meter can be fitted with up to three optional plug-in cards. The
slot bays of the plug-in cards are dedicated to a particular card function. The
plug-in card functions are: serial communications, analog output and setpoint
output. Only one card from each function category can be installed.
MODEL PAXCDL -ANALOG OUTPUT PLUG-IN OPTION CARD
SPECIFICATIONS
Analog Output Card
Types: 0 to 20 mA, 4 to 20 mA and 0 to 10 VDC
Isolation To Sensor & User Input Commons: 500 Vrms for 1 min.
Working Voltage: 50 V. Not isolated from all other commons.
PAXH Only:
Isolation To Sensor Common: 1400 Vrms for 1 min.
Working Voltage: 125 V
Isolation To User Input Common: 500 Vrms for 1 min.
Working Voltage: 50 V
Accuracy: 0.17% of FS (18 to 28°C); 0.4% of FS (0 to 50°C)
Resolution: 1/3500
Compliance:
10 VDC: 10 KΩload min.
20 mA: 500 Ωload max. (self-powered)
Update Time: 200 msec. max. to within 99% of final readout value (digital
filter and internal zero correction disabled)
700 msec. max. (digital filter disabled, internal zero correction enabled)
PAXH only: 1 sec. max. to within 99% of final readout value (digital filter
disabled)
MODEL NO. DESCRIPTION PART NUMBER
PAXCDL Analog Output Card PAXCDL10
TOP VIEW
Bulletin No. PAXCDL-D
Drawing No. LP0401
Released 3/08
Tel [phone]
Fax [phone]
www.redlion.net

Enter the analog output type. For 0-20 mA or 4-20 mA
use terminals 18 and 19. For 0-10 V use terminals 16 and
17. Only one range can be used at a time.








ANALOG TYPE
ANALOG ASSIGNMENT



SELECTION
0 to 10 V
4 to 20 mA
0 to 20 mA
RANGE
 
Enter the Display Value that corresponds to 0 mA (0-20
mA) , 4 mA (4-20 mA) or 0 VDC (0-10 VDC).




ANALOG LOW SCALE VALUE












ANALOG HIGH SCALE VALUE
ANALOG UPDATE TIME
PROBE BURN-OUT ACTION (PAXT ONLY)
to 
to 
to 
 
MODULE 8-Analog Output Parameters (  )
PARAMETER MENU
Indicates Program Mode Alternating Display.
Factory Settings are shown.




Parameter
Selection/Value
LIMITED WARRANTY
The Company warrants the products it manufactures against defects in materials and workmanship
for a period limited to two years from the date of shipment, provided the products have been stored,
handled, installed, and used under proper conditions. The Company’s liability under this limited
warranty shall extend only to the repair or replacement of a defective product, at The Company’s
option. The Company disclaims all liability for any affirmation, promise or representation with
respect to the products.
The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC against
damages, claims, and expenses arising out of subsequent sales of RLC products or products
containing components manufactured by RLC and based upon personal injuries, deaths, property
damage, lost profits, and other matters which Buyer, its employees, or sub-contractors are or may be
to any extent liable, including without limitation penalties imposed by the Consumer Product Safety
Act (P.L. 92-573) and liability imposed upon any person pursuant to the Magnuson-Moss Warranty
Act (P.L. 93-637), as now in effect or as amended hereafter.
No warranties expressed or implied are created with respect to The Company’s products except those
expressly contained herein. The Customer acknowledges the disclaimers and limitations contained
herein and relies on no other warranties or affirmations.
Enter the source for the analog output to retransmit:
 = Display Input Value
 = Maximum Display Input Value
 = Minimum Display Input Value
 = Totalize Display Value
Enter the Display Value that corresponds to 20 mA(0-20
mA) , 20 mA (4-20 mA) or 10 VDC (0-10 VDC).
Enter the analog output update rate in seconds. A value
of 0.0 allows the meter to update the analog output at a
rate of 20/sec.
Enter the probe burn-out action. In the event of a
temperature probe failure, the analog output can be
programmed for low or high scale.
Red Lion Controls
20 Willow Springs Circle
York PA 17406
Tel [phone]
Fax [phone]
Red Lion Controls AP
Unit 101, XinAn Plaza
Building 13, No.99 Tianzhou Road
ShangHai, P.R. China 200223
Tel [phone]
Fax [phone]
Red Lion Controls BV
Printerweg 10
NL - 3821 AD Amersfoort
Tel [phone]
Fax [phone]