Redexim Verti-Cut 1300 User manual

ATTENTION:
IT IS OF THE UTMOST IMPORTANCE TO READ THIS USER MANUAL CAREFULLY
PRIOR TO USING THE VERTI-CUT IN ORDER TO USE THE MACHINE SAFELY
AND TO OBTAIN THE BEST RESULTS.
1216 English 944.140.400
User Manual and
Parts Book
Verti-Cut 1300
Serial number:
Translation of the original operating
instructions

2
FOREWORD
Congratulations on your Verti-Cut purchase! For safe and long-lasting operation of this Verti-Cut,
it is necessary to read and to understand this user manual.
It is impossible to work safely with this machine without complete knowledge of its content.
The Verti-Cut is not a machine that works independently. It is the user’s responsibility to use the
correct tractor. The user must also check the tractor/Verti-Cut combination on safety aspects
such as noise level, user instructions and risk analysis.
The following pages deal initially with the general safety instructions. Every user should know
these safety instructions and apply them. At the end of this page, a registration card is inserted.
This registration card should be returned to enable us to deal with potential future claims.
This user manual lists many instructions that are numbered in sequence. You should follow this
sequence. A is an indication of a safety instruction. A means a tip and/or note.
All information and technical specifications provided at the moment that this document is
published are the most recent ones. Design specifications may be changed without prior notice.
This document is a translation of the original operating instructions.
Upon request, the original operating instructions are available in Dutch.
WARRANTY CONDITIONS
WITH DELIVERY THIS VERTI-CUT IS GUARANTEED AGAINST MATERIAL DEFECTS.
THIS WARRANTY IS VALID FOR A PERIOD OF 12 MONTHS FROM THE PURCHASE DATE.
VERTI-CUT WARRANTIES ARE SUBJECT TO THE ‘GENERAL CONDITIONS FOR SUPPLY OF
PLANT AND MACHINERY FOR EXPORT, NUMBER 188’ THAT ARE PUBLISHED UNDER THE
AUSPICES OF THE UNITED NATIONS ECONOMIC COMMISSION FOR EUROPE.
REGISTRATION CARD
For your own information, fill in the table below:
Serial number of the
machine
Dealer name
Date of purchase
Remarks

3
! SAFETY INSTRUCTIONS !
Figure 1
The Verti-Cut is designed for safe use. This can
only be achieved if you completely follow the
safety instructions described in this manual.
Read and understand (Figure 1) the manual before
you start using the Verti-Cut.
If the machine is not used as described in this
manual, this can result in injuries and/or damage
to the Verti-Cut.
(1) The user must be an expert in using the machine. The machine should be
professionally adjusted for cultivating the subsoil.
The manufacturer will not accept any liability for unprofessional use and its resulting
damage. All risks occurring with this are entirely at the expense of the user.
Following the use, maintenance and repair instructions prescribed by the manufacturer is
also considered professional use of this machine.
Inspect the area to be treated before using the Verti-Cut.
Remove loose obstacles and avoid irregularities.
(2) The Verti-Cut is manufactured according to the latest technical understanding
and is safe to use.
When unskilled people use, maintain or repair the machine, this could result in injuries to
the user and to third parties. This must be avoided!
Always use the Verti-Cut in combination with the correct tractor as described in the
technical data.
(3) All persons assigned to operate, maintain and repair the Verti-Cut by the
owner must completely read and understand the operation manual and in
particular the chapter of Safety Instructions.
The user is responsible for a safe Tractor/Verti-Cut combination. This entire
combination must be tested for noise, safety, risk and user friendliness. User
instructions should also be drafted.
(4) The user is obliged to check the Verti-Cut for visible damage and defects
before using the Verti-Cut.
Modifications to the Verti-Cut (including its operations) that have a negative impact on
safety must be rectified immediately.
For safety reasons it is in principle not permitted to make changes or adjustments to the
Verti-Cut (except those approved by the manufacturer).
If modifications to the Verti-Cut have been made, then the current CE marking is
cancelled. The person that has made these modifications has to apply for a new CE
marking himself. Check the Verti-Cut for loose bolts, nuts and components before every
operation.

4
If present, check the hydraulic pipelines regularly and replace these when the hydraulic
pipelines are damaged or appear old. The pipelines that are replaced should comply with
the technical requirements of the manufacturer.
If a hydraulic installation is present, you should always make it pressure-free before
working on this installation.
NEVER use the Verti-Cut in the absence of the safety stickers.
NEVER crawl under the Verti-Cut.
If necessary, tilt the Verti-Cut.
NEVER step off the tractor while the motor is running.
In case of maintenance, adjusting and repairs, it is necessary to block the Verti-Cut in
order to prevent sinking away, driving off and/or sliding off.
Always switch off the tractor motor, take the tractor’s key out off the ignition and
disconnect the Power Take-Off (PTO) in case of maintenance, adjusting and repairs
(Figure 2).
Figure 2
With regards to the safety of the machine and the user, use only original Verti-Cut parts
for maintenance and repairs.
Only authorised technical personnel may carry out repairs to the Verti-Cut.
Keep a record of the repair activities.
(5) The general applicable health & safety (Dutch: ARBO) regulations must also
be followed in addition to the instructions in this user manual.
Relevant traffic regulations also apply in case of using public roads.
Transporting persons is not permitted!
Do not use the Verti-Cut in the dark, in heavy rain/storm or on slopes with an angle larger
than 20 degrees.
(6) All persons that are going to operate the Verti-Cut must be familiar with all the
functions and control elements of the Verti-Cut before starting any work
activities.
Attach the Verti-Cut to the towing vehicle according to the regulations.
(Danger of injuries!)
Check whether you have a clear field of vision – both close by and far away – before you
depart.

5
Safety stickers
(Figure 2, 3 and 4) with an identical meaning are attached to both sides (Figure 5)
of the Verti-Cut. These safety stickers must always be clearly visible and legible and
must be replaced if they have become damaged.
During operation, NO persons are allowed within the danger zone of the Verti-Cut,
because there is danger of physical injuries caused by moving components. (Figure 3)
Figure 3
Figure 4
Keep a distance of minimum 4 metres!
(Figure 4)
Pay attention to the permitted lifting capacity of the towing vehicle.
Dress appropriately. Wear sturdy shoes with steel toecaps, long trousers and tie up long
hair. Do not wear loose clothing.
Figure 5
(7) Location of the safety stickers (Figure 5)
Used oil/grease is harmful to the environment. Dispose of these substances according to
the regulations that apply in your location.

6
EU DECLARATION
We,
Redexim BV
Utrechtseweg 127
3702 AC Zeist, Holland
declare entirely under our own responsibility that the product
VERTI-CUT WITH A MACHINE NUMBER AS INDICATED ON THE MACHINE AND
INDICATED IN THIS MANUAL
to which this declaration refers, complies with stipulation of the 2006/42/EC machine directive.
Zeist, 16.04.12
A.C. Bos
Manager Operations & Logistics
Redexim Holland

7
TABLE OF CONTENTS
FOREWORD ......................................................................................... 2
WARRANTY CONDITIONS .................................................................. 2
REGISTRATION CARD ........................................................................ 2
! SAFETY INSTRUCTIONS ! ............................................................... 3 
EU DECLARATION ............................................................................... 6
1.1Model ............................................................................................ 8
2.0GENERAL DESCRIPTION ........................................................... 8
3.0FIRST INSTALLATION OF THE VERTI-CUT .............................. 9
4.0ATTACHING / DETACHING THE VERTI-CUT .......................... 10
5.0THE POWER TAKE-OFF (PTO) ................................................ 11
5.1LENGTH OF THE PTO .............................................................. 11
5.2USING THE PTO ....................................................................... 12
6.0ADJUSTING THE WORKING DEPTH ....................................... 12
7.0TRANSPORTING THE VERTI-CUT .......................................... 12
8.0THE WORKING SPEED ............................................................ 12
9.0USING THE VERTI-CUT ............................................................ 13
10.0START/STOP PROCEDURE OF THE VERTI-CUT ................... 13
11.0TROUBLE SHOOTING (PROBLEM ANALYSIS) ....................... 14
12.0MAINTENANCE ......................................................................... 14
13.0TIGHTENING THE V-BELTS OF THE VERTI-CUT ................... 16
13.1CHANGING / REPLACING THE KNIVES .................................. 18

8
1.0 TECHNICAL DATA
1.1 Model Verti-Cut 1300
Working width 1300mm (51,2”)
Working depth (In case of a non-
worn knives) 0mm - 40mm (0” - 1.57”)
Distance between the knives 30mm
Working speed Depending on the conditions
Recommended tractor 18 HP with minimum lifting capacity of 185 kg
(408 lbs)
PTO rpm Maximum 540 rpm
Weight 155 kg (342 lbs)
Capacity
(Theoretical at a speed of 5 km/h (3.1
mph))
6500 m2/h (21325 ft2/h)
Dimensions L x W x H
692 x 1616 x 801 mm
27.2” x 63.6” x 31.5”
Gearbox/motor oil SAE 90
Grease EP 2
Standard components - Knives 2 mm
- PTO
Optional - Knives 1mm
- Knives 3mm
2.0 GENERAL DESCRIPTION
The Verti-Cut is a machine for aerating grass surfaces.

9
Verti-Cut
Figure 6
3.0 FIRST INSTALLATION OF THE VERTI-CUT
The machine is placed in the transport position on the pallet. To remove the pallet and to place
the machine horizontally on the ground, you take the following steps (see Figure 6):
NEVER crawl under the machine!
1. Attach a cable to the lifting eye.
Make sure that the cable/crane/lift can hoist minimum twice the weight of
the machine. (See Chapter 1.0 ‘Technical Data’ for the weight details.)
2. Remove the transport straps (1).
3. Lift the machine off the pallet.
4. Pull the pallet from under the machine.
NEVER crawl under the machine!
5. Slowly lower the machine until it touches the ground.
6. Attach the machine to a tractor. (See Chapter 4.0 for instructions about attaching to the tractor.)
Use the proper tractor (please refer to the specifications).
Turn off the tractor and secure the tractor/Verti-Cut combination against
driving off and/or sliding off.

10
4.0 ATTACHING / DETACHING THE VERTI-CUT
Checking procedure before starting to attach the Verti-Cut:
 Check the Verti-Cut for visually discernable damage and repair this
if safe operation of the machine is no longer guaranteed.
 Check whether all the nuts and bolts are tight.
 Check whether all protection caps and all safety stickers are
present on the machine and are not damaged.
NEVER use the machine without these items.
Figure 7
The Verti-Cut can be attached to the tractor by means of the 3-point attachment.
The procedure is as follows (see Figure 7):
1. Drive the tractor carefully backwards so that the lower connecting arms can be
attached to the frame.
Make sure that the tractor is blocked well and cannot move on its own
accord!
Switch off the tractor before descending!
2. Connect the lower connecting arms to the 3-point pins (1) and secure these with
the supplied locking pins.
3. Set the stabilizer of the tractor to 100mm lateral stroke.
4. Connect the top rod (2) to the frame with the pin (3); secure the pin (3) with the
supplied locking pin.
Make sure that all the securing pins are locked!
5. Turn the top rod (3) inwards so that it becomes pressurized.
6. Connect the PTO between the Verti-Cut and the tractor.
7. Start the tractor and lift the Verti-Cut off the subsoil.
8. Slide the adjustable legs (4) upwards and secure these with the locking pin(s).
Detaching is done in reverse order.