Reebok T 9.80 User manual

CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Serial Number
Decal
Model No. RBTL21908.0
Serial No.
Write the serial number in the space
above for reference.
www.reebokfitness.com
QUESTIONS?
f you have questions, or if parts are
damaged or missing, DO NOT
CONTACT THE STORE; please
contact Customer Care.
IMPORTANT: You must note the
product model number and
serial number (see the drawing
above) before contacting us:
CALL TOLL-FREE:
1-877-994-4999
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
www.reebokservice.com
USER'S MANUAL

TABLE OF CONTENTS
WARNNGDECALPLACEMENT ..............................................................2
MPORTANTPRECAUTONS .................................................................3
BEFOREYOUBEGN .......................................................................5
ASSEMBLY ...............................................................................6
OPERATONANDADJUSTMENT ............................................................14
HOWTOFOLDANDMOVETHETREADMLL ..................................................23
TROUBLESHOOTNG ......................................................................25
EXERCSEGUDELNES ...................................................................28
PARTLST ...............................................................................29
EXPLODEDDRAWNG ......................................................................31
ORDERNGREPLACEMENTPARTS ..................................................BackCover
LMTEDWARRANTY...............................................................BackCover
This drawing shows the locations of the
warning decals. If a decal is missing or il-
legible, call the telephone number on the
front cover of this manual and request a
free replacement decal. Apply the decal
in the location shown. Note: The decals
may not be shown at actual size.
WARNING DECAL PLACEMENT
2
REEBOK and the Vector Logo are registered trademarks and service marks of Reebok. This product is
manufactured and distributed under license from Reebok nternational.

1. Before beginning this or any exercise pro-
gram, consult your physician. This is espe-
cially important for persons over the age of
35 or persons with pre-existing health prob-
lems.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
4. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air open-
ings. To protect the floor or carpet from dam-
age, place a mat under the treadmill.
5. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
7. Keep children under age 12 and pets away
from the treadmill at all times.
8. The treadmill should be used only by per-
sons weighing 325 lbs. (147 kg) or less.
9. Never allow more than one person on the
treadmill at a time.
10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose
clothes that could become caught in the
treadmill. Athletic support clothes are recom-
mended for both men and women. Always
wear athletic shoes. Never use the treadmill
with bare feet, wearing only stockings, or in
sandals.
11. When connecting the power cord (see page
14), plug the power cord into a surge suppres-
sor (not included) and plug the surge sup-
pressor into a grounded circuit capable of
carrying 15 or more amps. No other appliance
should be on the same circuit. Do not use an
extension cord.
12. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 14. To purchase a surge suppressor, see
your local REEBOK dealer or call the tele-
phone number on the front cover of this man-
ual and order part number 146148, or see your
local electronics store.
13. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may slow,
accelerate, or stop unexpectedly, which may
result in a fall and serious injury.
14. Keep the power cord and the surge suppres-
sor away from heated surfaces.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
TROUBLESHOOTING on page 25 if the tread-
mill is not working properly.)
16. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 16).
17. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
WARNING: To reduce the risk of serious injury, read all important precautions and in-
structions in this manual and all warnings on your treadmill before using your treadmill. ICON as-
sumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
IMPORTANT PRECAUTIONS
3

18. The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
19. The pulse sensors are not medical devices.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensors are intended
only as an exercise aid in determining heart
rate trends in general.
20. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and switch the reset/off cir-
cuit breaker to the “off” position when the
treadmill is not in use. (See the drawing on
page 5 for the location of the reset/off circuit
breaker.)
21. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 23.) You
must be able to safely lift 45 lbs. (20 kg) to
raise, lower, or move the treadmill.
22. Do not change the incline of the treadmill by
placing objects under the treadmill.
23. When folding or moving the treadmill, make
sure that the storage latch is holding the
frame securely in the storage position.
24. Inspect and properly tighten all parts of the
treadmill regularly.
25. Never insert or drop any object into any
opening on the treadmill.
26. DANGER: Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
27. The treadmill is intended for in-home use
only. Do not use the treadmill in any commer-
cial, rental, or institutional setting.
4
SAVE THESE INSTRUCTIONS

5
Thank you for selecting the revolutionary REEBOK®
T 9.80 treadmill. The T 9.80 treadmill offers an impres-
sive selection of features designed to make your work-
outs at home more enjoyable and effective. And when
youʼre not exercising, the unique treadmill can be
folded up, requiring less than half the floor space of
other treadmills.
For your benefit, read this manual carefully before
using the treadmill. f you have questions after read-
ing this manual, please see the front cover of this man-
ual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
To avoid a registration fee for any service needed
under warranty, you must register the treadmill at
www.reebokservice.com/registration.
Before reading further, please look at the drawing
below and familiarize yourself with the labeled parts.
BEFORE YOU BEGIN
Handrail
Console
Key/Clip
Reset/Off
Circuit Breaker
Walking Belt
Foot Rail Power Cord
dler Roller
Adjustment Bolts
Accessory Tray
Pulse Sensor
Platform Cushion

6
ASSEMBLY
To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480.
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking
belt is coated with high-performance lubricant. During shipping, some lubricant may be transferred to the top of
the walking belt or the shipping carton. This is normal and does not affect treadmill performance. f there is lubri-
cant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex keys and your own Phillips screwdriver and
adjustable wrench .
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART L ST near the end of this manual. The number after the parentheses
is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it is preattached
to one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assem-
bly. Extra hardware may be included.
3/8" Star
Washer (11)–10
#8 x 3/4" Screw
(1)–4
3/8" Nut (12)–5
#8 x 1/2" Screw
(2)–12
#8 x 1" Tek Screw
(4)–6
Base Foot
Spacer (85)–6
3/8" x 1 1/4"
Patch Bolt (9)–4
3/8" x 2" Bolt (6)–3 3/8" x 2 3/4" Bolt (7)–4
3/8" x 1"
Patch Bolt (8)–2
1/4" x 1/2"
Bolt (3)–2 3/8" x 3/4"
Bolt (10)–2

7
2. Attach a Wheel (91) to an Extension Leg (88)
with a 3/8" x 2 3/4" Bolt (7) and a 3/8" Nut (12).
Do not overtighten the Nut; the Wheel must
turn freely.
2
1. Make sure that the power cord is unplugged.
With the help of a second person, carefully tip
the treadmill onto its left side. Partially fold the
Frame (51) so the treadmill is more stable. Do
not fully fold the Frame until the treadmill is
completely assembled.
Attach six Base Feet (86) and six Base Foot
Spacers (85) to the Base (83) and the Extension
Legs (88) in the locations shown with six #8 x 1"
Tek Screws (4); do not overtighten the Tek
Screws.
1
7
12
91
88
83
88
88
4
86
86
86
85
51
85
85
85 86
4
85 4
86
854
4
4

8
3. dentify the Right Upright (100), which is marked
with a sticker. Have a second person hold the
Right Upright near Base (83) as shown.
See the inset drawing. Tie the wire tie in the
Right Upright (100) securely around the end of
the Upright Wire (76). Then, pull the other end
of the wire tie until the Upright Wire is routed
completely through the Right Upright.
3
100
Wire
Tie
76
4. Orient the Right Upright (100) with the bend in
the plate positioned as shown.
Attach the Right Upright (100) to the Base (83)
with a 3/8" x 2 3/4" Bolt (7), a 3/8" x 1" Patch
Bolt (8), and two 3/8" Star Washers (11); do not
fully tighten the Bolts yet. Be careful not to
pinch the Upright Wire (76).
4
7
11
8
Plate
100
83
5. With the help of a second person, carefully tip
the treadmill onto its right side. Partially fold the
Frame (51) so the treadmill is more stable. Do
not fully fold the Frame until the treadmill is
completely assembled.
Orient the left Upright (77) with the bend in the
plate positioned as shown.
Attach the left Upright (77) to the Base (83) with
a 3/8" x 2 3/4" Bolt (7), a 3/8" x 1" Patch Bolt (8),
and two 3/8" Star Washers (11); do not fully
tighten the Bolts yet.
Attach a Wheel (91) to an Extension Leg (88)
with a 3/8" x 2 3/4" Bolt (7) and a 3/8" Nut (12).
Do not overtighten the Nut; the Wheel must
turn freely.
With the help of a second person, tip the tread-
mill so that the Base (83) is flat on the floor.
5
8
91
12
7
11
88
83
77
Plate
7
51
76
77
Wire Tie
76
83

9
6. Set the console assembly face down on a soft
surface to avoid scratching the console assem-
bly. dentify the Right Handrail (102), which is
marked with a sticker. Hold the Right Handrail
near the console assembly.
Next, insert the console wire into the large hole
directly below the indicated hole in the Right
Handrail (102) and out of the top as shown.
6
102
Console Wire
Hole
Console
Assembly
7. Locate the speed wire in the end of the Pulse
Bar (99). Connect the speed wire in the Right
Handrail (102) to the speed wire in the Pulse
Bar. See the inset drawing. The connectors
should slide together easily and snap into
place. f they do not, turn one connector and try
again.
Locate the incline wire in the end of the Pulse
Bar (99). Hold the Left Handrail (94) near the
console assembly. Connect the incline wire in
the Left Handrail to the incline wire in the Pulse
Bar as described above.
7
102
94
99
Console
Assembly
Speed Wires
ncline
Wires
8. nsert the speed wires and incline wires into the
area at the end of the Pulse Bar (99). Connect
the Left Handrail (94) to the console assembly
with two #8 x 1/2" Screws (2), a 3/8" x 3/4" Bolt
(10), and a 3/8" Star Washer (11). Make sure
no wires are pinched.
Attach the Right Handrail (102) to the con-
sole assembly in the same way.
8
2
11
10
94
Console
Assembly
2
10
11
102
99

10
9. Press the Left Handrail Cover (95) upward
against the console assembly. See the inset
drawing. Align the lip on the Left Handrail
Cover with the lip on the console assembly.
Leave a small gap between the Left Handrail
Cover and the console assembly. Make sure
that no wires are pinched. Then, tighten the
four #8 x 1/2" Screws (2) in the Left Handrail
(94). Note: The Screws are preattached.
Attach the Right Handrail Cover (103) to the
console assembly in the same way.
Tighten two 1/4" x 1/2" Patch Bolts (3) into the
Handrails (94, 102) and the console assembly.
9
Console
Assembly
3
3
95
103
22
22
Lips
94
102
10. dentify the Left Accessory Tray (113) and the
Right Accessory Tray (114). Attach the
Accessory Trays to the console assembly with
eight #8 x 1/2" Screws (2).
2
10 2
Console
Assembly
114
113

11
11. Have a second person hold the console assem-
bly near the Uprights (77, 100).
Connect the Upright Wire (76) to the console
wire extending from the console assembly. See
the inset drawing. The connectors should
slide together easily and snap into place. f
they do not, turn one connector and try again. IF
THE CONNECTORS ARE NOT CONNECTED
PROPERLY, THE CONSOLE MAY BE DAM-
AGED WHEN THE POWER IS TURNED ON.
Remove the wire tie from the Upright Wire (76).
nsert the excess wire into the Right Upright
(100) as you set the console assembly on the
Right Upright and the Left Upright (77). Be
careful not to pinch any wires.
Console
Assembly
11
100
Wire
Tie
Console
Wire
76
76
Console
Wire
77
12. Attach the console assembly to the Uprights
(77, 100) with four 3/8" x 1 1/4" Patch Bolts (9)
and four 3/8" Star Washers (11). Start all four
Patch Bolts before tightening any of them. Console
Assembly
12
100
11
11
9
9
11
9
9
77
11

12
13. Attach the Right Bottom Handrail Cover (104)
and the Left Bottom Handrail Cover (96) to the
console assembly with four #8 x 3/4" Screws
(1).
Console
Assembly
1
13
96
104
1
14. Raise the Frame (51) to the position shown.
Have a second person hold the Frame until
this step is completed.
Orient the Storage Latch (80) so that the large
barrel and the Latch Knob (81) are oriented as
shown.
Attach the Latch Bracket (90) and Storage Latch
(80) to the Base (83) with two 3/8" x 2" Bolts (6)
and two 3/8" Nuts (12).
Attach the upper end of the Storage Latch (80)
to the bracket on the Frame (51) with a 3/8" x 2"
Bolt (6) and a 3/8" Nut (12). Note: t may be
necessary to move the Frame back and forth to
align the Storage Latch with the bracket.
Lower the Frame (51) (see HOW TO LOWER
THE TREADM LL FOR USE on page 24). 12
12
Large
Barrel
83
6
51
14
6
81
80
90

13
16. Make sure that all parts are properly tightened before you use the treadmill. Keep the included hex keys
in a secure place; one of the hex keys is used to adjust the walking belt (see pages 26 and 27). To protect
the floor or carpet from damage, place a mat under the treadmill.
15. With the help of a second person, carefully
lower the Uprights (77, 100). Firmly tighten the
two 3/8" x 2 3/4" Bolts (7) and the two 3/8" x 1"
Patch Bolts (8). Raise the Uprights to the verti-
cal position.
100
87
8
7
77
15

14
OPERATION AND AD USTMENT
THE PRE-LUBRICATED WALKING BELT
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your homeʼs power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local REEBOK dealer or call the telephone
number on the front cover of this manual and order
part number 146148, or see your local electronics
store.
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate, or stop unexpect-
edly, which may result in a fall and serious injury.
This product must be grounded. f it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
IMPORTANT: The treadmill is not compatible with
GFCI-equipped outlets.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
DANGER: Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
2
Grounded Outlet Box
Grounded Outlet Box
Grounding Plug
Surge Suppressor
Surge Suppressor
Grounding Pin
Adapter
Lug
Metal Screw
Grounded Outlet
Grounding Pin

15
FEATURES OF THE CONSOLE
The treadmill console offers an impressive selection of
features designed to make your workouts more effec-
tive and enjoyable. When the manual mode of the con-
sole is selected, the speed and incline of the treadmill
can be changed with the touch of a button. As you ex-
ercise, the console will display continuous exercise
feedback. You can even measure your heart rate using
the handgrip pulse sensor.
n addition, the console features twenty speed work-
outs—five weight loss workouts, five aerobic workouts,
five performance workouts, and five endurance work-
outs. Each workout automatically controls the speed
and incline of the treadmill as it guides you through an
effective exercise session. You can even create your
own custom workouts and save them for future use.
The console also features the new iFit nteractive
Workout system. The iFit system enables the console
to accept iFit nteractive Workout Cards containing
workouts designed to help you achieve specific fitness
goals. For example, lose unwanted pounds with the 8-
week Weight Loss workout, or train for a long-distance
run with the Marathon workout. iFit workouts automati-
cally control the treadmill while the voice of a personal
trainer coaches you through every step of your workout.
iFit cards are available separately. To purchase iFit
cards at any time, go to www.iFit.com or call the
telephone number on the front cover of this man-
ual. iFit cards are also available at select stores.
Whether you select the manual mode or a workout,
you can listen to your favorite workout music or audio
books with the consoleʼs premium stereo sound system.
To turn on the power, see page 16. To use the man-
ual mode, see page 16. To use a speed workout, see
page 18. To create and use a custom workout, see
pages 19 and 20. To use an iFit workout, see page
21. To use the information mode, see page 22. To
use the stereo sound system, see page 22.
IMPORTANT: If there is a sheet of clear plastic on
the face of the console, remove the plastic. To pre-
vent damage to the walking platform, wear clean
athletic shoes while using the treadmill. The first
time the treadmill is used, observe the alignment of
the walking belt, and center the walking belt if nec-
essary (see page 27).
CONSOLE
DIAGRAM
Audio
Jack

16
HOW TO TURN ON THE POWER
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room tem-
perature before turning on the power. If you do not
do this, you may damage the console displays or
other electrical components.
Plug in the power cord (see
page 14). Next, locate the
reset/off circuit breaker on
the treadmill frame near the
power cord. Make sure that
the circuit breaker is in the
“reset” position.
IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is dis-
played in a store. If the displays light as soon as
you plug in the power cord and switch the reset/off
circuit breaker to the reset position, the demo
mode is turned on. To turn off the demo mode,
hold down the Stop button for a few seconds. If the
displays remain lit, see THE INFORMATION MODE
on page 22 to turn off the demo mode.
Next, stand on the
foot rails of the
treadmill. Locate
the clip attached to
the key (see the
drawing at the
right), and slide
the clip securely
onto the waistband
of your clothes. Then, insert the key into the console.
After a moment, the displays will light. IMPORTANT:
In an emergency situation, the key can be pulled
from the console, causing the walking belt to slow
to a stop. Test the clip by carefully taking a few
steps backward; if the key is not pulled from the
console, adjust the position of the clip.
Note: The console can display speed and distance in
either miles or kilometers. To find out which unit of
measurement is selected or to change the unit of mea-
surement, see THE NFORMAT ON MODE on page
22. For simplicity, all instructions in this section refer to
miles.
HOW TO USE THE MANUAL MODE
1. Insert the key into the console.
See HOW TO TURN ON THE POWER at the left.
2. Select the manual mode.
Each time the key is in-
serted, the manual mode
will be selected. f you
have selected a workout,
press any of the speed
workout buttons (Wt.
Loss, Aerobic, Performance, or Endurance) repeat-
edly until a track appears in the matrix.
3. Start the walking belt and adjust the speed.
To start the walking belt, press the Start button,
one of the Speed increase buttons, or one of the
speed buttons numbered 1 to 12.
f you press the Start button or one of the Speed
increase buttons, the walking belt will begin to
move at 1 mph. As you exercise, change the
speed of the walking belt as desired by pressing
the Speed increase and decrease buttons on the
console or in the right handrail. Each time you
press a button, the speed setting will change by
0.1 mph; if you hold down the button, the speed
setting will change in increments of 0.5 mph. f you
press one of the numbered speed buttons, the
walking belt will gradually change speed until it
reaches the selected speed setting.
To stop the walking belt, press the Stop button. To
restart the walking belt, press the Start button, one
of the Speed increase buttons, or one of the num-
bered speed buttons.
4. Change the incline of the treadmill as desired.
To change the incline of the treadmill, press one of
the ncline increase or decrease buttons or one of
the incline buttons numbered 0 to 12.
Each time you press one of the ncline increase or
decrease buttons on the console or in the left
handrail or one of the numbered incline buttons,
the incline will gradually change until it reaches the
selected incline setting.
Reset
Position
Clip
Key

17
5. Follow your progress with the displays.
The matrix—When you
select the manual
mode, the matrix will
display a track that rep-
resents 1/4 mile (400
meters). As you exer-
cise, the indicators around the track will appear in
succession until the entire track appears. The track
will then disappear and the indicators will again
begin to appear in succession.
The Incline/Pulse dis-
play—The ncline/Pulse
display can show the in-
cline of the treadmill.
The display will also
show your heart rate
when you use the handgrip pulse sensor.
The Time display—
The Time display will
show the elapsed time.
Note: When a speed
workout is selected, the
display will show the
time remaining in the workout instead of the
elapsed time.
The Distance
display—The Distance
display can show the
distance that you have
walked or run.
The Calorie/Speed dis-
play—The Speed dis-
play will show the ap-
proximate number of
calories you have
burned and the speed of
the walking belt for a few seconds each.
To reset the console, press the Stop button, re-
move the key, and then reinsert the key.
6. Measure your heart rate if desired.
Before using
the handgrip
pulse sensor,
remove the
sheets of clear
plastic from the
metal contacts.
n addition,
make sure that
your hands are
clean.
To measure your heart rate, stand on the foot
rails and hold the metal contacts on the handrail—
avoid moving your hands. Hold the contacts for
approximately ten seconds. When your pulse is
detected, several dashes will appear and then your
heart rate will be shown. For the most accurate
heart rate reading, continue to hold the con-
tacts for about 15 seconds.
7. Turn on the fans if desired.
The fans feature high and low speed settings.
Press the Fans button repeatedly to select a fan
speed or to turn off the fans. Note: f the fans are
on when the walking belt is stopped, the fans will
turn off automatically after a few minutes.
8. When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when you fold the treadmill to the storage posi-
tion, or you may damage the treadmill. Next, re-
move the key from the console and put it in a secure
place.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the “off” position and
unplug the power cord. IMPORTANT: If you do
not do this, the treadmillʼs electrical compo-
nents may wear prematurely.
Contacts

18
HOW TO USE A SPEED WORKOUT
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page 16.
2. Select a speed workout.
To select a speed workout, press the Wt. Loss but-
ton, the Aerobic button, the Performance button, or
the Endurance button.
When a speed workout
is selected, the displays
will show the maximum
incline setting, the dura-
tion of the workout, and
the maximum speed
setting of the workout. n addition, a profile of the
speed settings of the workout will scroll across the
matrix.
3. Start the walking belt.
Press the Start button, one of the speed increase
buttons, or one of the numbered speed buttons to
start the workout. A moment after you press the
button, the treadmill will automatically adjust to the
first speed and incline settings of the workout. Hold
the handrails and begin walking.
Each workout is divided into one-minute segments.
One speed setting and one incline setting are pro-
grammed for each segment. Note: The same speed
and/or incline setting may be programmed for con-
secutive segments.
During the workout, the
profile will show your
progress. The flashing
segment of the profile
represents the current
segment of the workout.
The height of the flashing segment indicates the
speed setting for the current segment. At the end of
each segment, a series of tones will sound and the
next segment of the profile will begin to flash. f a
new speed and/or incline setting is programmed for
the next segment, the new speed and/or incline set-
ting will appear in the displays for a few seconds
and the treadmill will automatically adjust to the
new speed and/or incline setting.
f the speed or incline setting is too high or too low
at any time during the workout, you can manually
override the setting by pressing the speed or incline
buttons; however, when the next segment of the
workout begins, the treadmill will automatically
adjust to the speed and incline settings for the
next segment.
To stop the workout at any time, press the Stop
button. To restart the workout, press the Start but-
ton or the Speed increase button. The walking belt
will begin to move at 1 mph. When the next seg-
ment of the workout begins, the treadmill will auto-
matically adjust to the speed and incline settings for
the next segment.
The workout will continue in this way until the last
segment of the workout ends. The walking belt will
then slow to a stop.
4. Follow your progress with the displays.
See step 5 on page 17.
5. Measure your heart rate if desired.
See step 6 on page 17.
6. Turn on the fans if desired.
See step 7 on page 17.
7. When you are finished exercising, remove the
key from the console.
See step 8 on page 17.
Current Segment

19
HOW TO CREATE A CUSTOM WORKOUT
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page 16.
2. Select a custom workout.
To select a custom workout, press one of the
Custom buttons repeatedly. When a custom work-
out is selected, the displays will show the maxi-
mum incline setting, the duration of the workout,
and the maximum speed setting of the workout. n
addition, three columns of indicators will appear in
the matrix.
Note: If more than
three columns of indi-
cators scroll across
the matrix, see HOW
TO USE A CUSTOM
WORKOUT on page
20.
3. Start the walking belt and program the desired
speed and incline settings.
Press the Start button, one of the speed increase
buttons, or one of the numbered speed buttons to
start the workout. A moment after you press the
Start button, the walking belt will begin to move.
Hold the handrails and begin walking.
Each custom workout is divided into several one-
minute segments. One speed setting and one in-
cline setting can be programmed for each seg-
ment. To program speed and incline settings for
the first segment, simply adjust the speed and in-
cline of the treadmill as desired by pressing the
speed and incline buttons.
When the first segment of the workout ends, a se-
ries of tones will sound and the current speed and
incline settings will be saved in memory. Program
a speed setting and an incline setting for the sec-
ond segment in the same way.
Continue programming speed and incline settings
for as many segments as desired; custom work-
outs can have up to forty segments. When you are
finished with your workout, press the Stop button
twice. The speed and incline settings that you have
programmed and the workout time will then be
saved in memory.
4. Follow your progress with the displays.
See step 5 on page 17.
5. Measure your heart rate if desired.
See step 6 on page 17.
6. Turn on the fans if desired.
See step 7 on page 17.
7. When you are finished exercising, remove the
key from the console.
See step 8 on page 17.

20
HOW TO USE A CUSTOM WORKOUT
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page 16.
2. Select a custom workout.
To select a custom
workout, press one of
the Custom buttons re-
peatedly. When a cus-
tom workout is selected,
the displays will show
the maximum incline setting, the duration of the
workout, and the maximum speed setting of the
workout. n addition, three columns of indicators
will appear in the matrix. Note: If only three
columns of indicators scroll across the matrix,
see HOW TO CREATE A CUSTOM WORKOUT
on page 19.
3. Start the walking belt.
Press the Start button, one of the speed increase
buttons, or one of the numbered speed buttons to
start the workout. A moment after you press the
Start button, the treadmill will automatically adjust
to the first speed and incline settings that you pro-
grammed previously. Hold the handrails and begin
walking.
Each custom workout is divided into several one-
minute segments. One speed setting and one in-
cline setting are programmed for each segment.
Note: The same speed and/or incline setting may
be programmed for consecutive segments.
The custom workout will function in the same way
as a speed workout (see step 3 on page 18).
f desired, you can redesign the workout while
using it. To change the speed setting or the in-
cline setting for the current segment, simply
press the speed or incline buttons. When the current
segment ends, the new setting will be saved in mem-
ory. To increase the length of the workout, first
wait until the workout is completed. Then, press the
Start button and program speed and incline settings
for as many additional segments as desired. When
you have added as many segments as desired,
press the Stop button twice. To decrease the
length of the workout, press the Stop button twice
at any time before the workout is completed.
To stop the workout temporarily, press the Stop
button. To restart the workout, press the Start but-
ton. The walking belt will begin to move at 1 mph.
When the next segment of the workout begins, the
treadmill will automatically adjust to the speed and
incline settings programmed for the next segment.
4. Follow your progress with the displays.
See step 5 on page 17.
5. Measure your heart rate if desired.
See step 6 on page 17.
6. Turn on the fans if desired.
See step 7 on page 17.
7. When you are finished exercising, remove the
key from the console.
See step 8 on page 17.