Reelworks 2782 Series User manual

Mutifunction Air Hose Reel 2782 Series
Instruction
Air Hose Reel Instruction
Technical Details
Spring driven drum: for automatic retractable.
Locking ratchet: to maintain the desired length of hose in use.
Safety Precautions
GENERAL SAFETY RULES
WARNING: Read and understand all instructions.
WARNING:
The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions or situations that could occur. It must be understood by the
operator that common sense and caution are factors which cannot be built into this product, but
must be supplied by the operator.
Hose Reel Safety Precautions
1. Use proper eye protection when assembling and using the hose reel.
2. Keep children away from the work area.
3. Personal injury and/or equipment damage may result if proper safety precautions are not
observed.
4.Ensure that reel is properly installed before connecting input and output hoses.
5. Bleed fluid/gas pressure from system before servicing reel.
6. Before connecting reel to supply line ensure that pressure does not exceed maximum
working pressure rating of reel.
7. Remember, even low pressure is very dangerous and can cause personal injury or death.
8. If a leak occurs in the hose or reel, remove system pressure immediately.
9. Ensure that reel, hose, and equipment being service are properly grounded.
10. If reel ceases to unwind or rewind, remove system pressure immediately.
11. Do not pull or jerk on hose.
Installation of Hose Reel
You will need to purchase appropriate hardware for mounting your new reel.
1) For mounting: For air series, Install reel on the wall and ceiling at most 9feet / 3m above the
floor. For water series, Install reel on the wall at most 4.5feet / 1.5m above the floor .
2) The reel base has two mounting holes for mounting on a suitable flat surface for air
series(four mounting holes for water series). Below figures is a template showing the correct
location of the mounting holes in the base.
3) Using the mounting holes in the base, mount the reel in the desired location. Be sure to use
appropriate hardware and tighten securely.
1 OF 3
REV 03/08/16
Item
27827153 300/20 -40˚C~+60˚C
-40˚F~+140˚F
Hybrid
Polymer
3/8" /10 15/50 Stop at any point
Slow Retraction
1/4"NPT or
3/8"BSPT
Work Tem.(˚C)Material
Hose Capacity
I.D.
(inch/mm)
Length
(m/ft)
Inlet/
Outlet Remarks
Max
Pressure
(psi/bar)
WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure
to follow the safety rules and other basic safety precautions may result in serious personal
injury.
Save these instructions in a safe place and on hand so that they can be read when required.

Air Hose Reel Instruction Air Hose Reel Instruction
On the wall & ceiling
4) The end of incoming hose can be connected to desired supply source.
5) Outlet fittings on reel hose attach to desired tool, or nozzle. Check connection for leakage,
also check hose reel for correct operation. See: Operation section.
6) If hose stopper adjustment is required, pull hose from reel and allow to latch at desired
length. Loosen stopper bolts, and slide stopper to a position close to the hose guide. Tighten
stopper bolts, and unlatch the reel.
Operation
1. Check reel for correct operation by slowly pulling out the hose.
2. To latch the reel, slowly pull out the hose to any point, Relax the hose to stop. Note：it can
not exceed the back end mark When the hose is pulled out,
3. To unlatch the reel,slowly pull the hose after relax，and then let the hose retract until the
hose stop rests against the hose guide.
Note: To avoid damage to the reel, always hold on to the hose while it is rewinding.
4. Periodically check the hose condition for wear or damage, and check the swivel fitting for
leakage. Replace any worn, damaged, or leaking parts.
Maintenance
Make sure the hose is in proper working order.
Clean the hose with a cloth dipped in warm water to remove dirt or deposits and ensure correct
rewinding.
Do not use detergents or solvents which could prove incompatible with cable-winder materials.
Dismantling of the unit by unskilled personal could prove hazardous; the risk involved mainly
concern the preloaded springs.
2 OF 3
Limited Warranty
1. The manufacturer warrantees this hose reel against defects in material and craftsmanship, for
a period of 24 months from date of purchase, but not including hose and O-ring parts.
2. Manufacturer’s liability is limited to replacement or repair of defective material within the
warranty period, when returned freight prepaid to the distributor or their designated service
depot.
3. The warranty does not cover damage caused by accident, misuse or faulty installation.
4. The reel must be installed and maintained in compliance with the instructions.
Explore and Parts List
3 OF 3
Part No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Description
Hose Assembly
O-Ring
Gear
Stop at any point Assembly
Screws
Support cover
O-Ring
Spool
Drum
Fixed pin
Base
Hose Compositor assembly
Screws
Screws
Label
Pre tightening cover
Q’ty
1
2
1
1
1
6
2
1
2
2
1
1
8
18
2
1
Part No.
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Description
Right casing
Baffle
Synchronous belt
Synchronous wheel
Screws
Spring
Hose Assembly
Guide bar
Slow Retraction assembly
Bumper Block assembly
Left shell
Fixed film
Hose Clamp
Screws
Side cover
Q’ty
1
1
1
1
4
1
1
1
1
1
1
1
1
2
2
Size: 145x210mm REV 03/08/16 3.02.01.137157克铜版纸
15
31
1
14
28
2
27
3
26
10
7
24
9
811
19
12
18 17 16 20
23
13
2122
29
25
64 5
30