ReelCraft 7000 Series User manual

1. Do not use reel at higher pressures or temperatures than listed on
the back of this bulletin.
2. Remove all spring tension before beginning dissassembly process.
SAFETY
INSTALLATION: A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.
LUBRICATION: Hose reel spring and bearings are factory lubricated and require no further lubrication.
REPLACING HOSE: 1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to swivel joint and secure hose with clamps.
ADJUSTMENTS: To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
REPAIRS: Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
7600 OMB55
Operating Instructions
Series 7000 Spring Driven Hose Reels
Medium Pressure Model Number:
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: [phone]
Customer Service: 855-634-9109 • [email protected] • www.reelcraft.com
Form# 1003-1099 Rev: 8/2015
MOUNTING: The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the
reel at the desired position and replace the screws.
Dimensions
A20 1/4”
B19 3/4”
C7 13/16”
D3 7/8”
E 7”

Series 7000 Spring Driven Hose Reels
Page 2 www.reelcraft.com
Item # Part # # Req. Description Item # Part # # Req. Description Item # Part # # Req. Description
1 600374-1B 1 Swivel Ass’y 9 300007 2 1¼” Snap Ring 18 S393-2 1 10-32 Shoulder Screw
2 600304 1 Hose Bumper Ass’y 10 600016 1 Base Ass'y 19 600018 1 Latch Pawl Ass’y
3 600361 1 Drive Spring Ass’y 11 S35-84 1 1/2-13 x 1/2" Set Screw 20 S76-106 1 3/8-24 Jam Nut
4 600621 1 Spring Arbor Ass’y 12 600017 1 Guide Arm Ass'y 21 260031 1 Spring Case Stud
5 260069 1 Gasket 13 300107 4 5/16-18 Lock Nut 22 600364 1 Sheave Ass’y
6 260074 1 Spring Case & Ratchet 14 S82-15 1 10-32 x 3/8" Lock Nut 23 3-117440 1 U-Bolt Hose Clamp
7 300011 6 10-32 Hex Lock Nut 15 S280-8 1 1/2-20 Hex Flange Nut 24 261650-1 2 1/4-20 Nyloc Nut
8 261046-B 1 Main Shaft 16 260067 1 Latch Spring 25 S257-25 1 Swivel Union
Reel Inlet Connection 3/8” F.P.T.
Max. Operating Pressure 3000 P.S.I.
Max. Operating Temperature 210 °F
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
19
20
21
22
23
24
25