Reflex Servitec 35-95 User manual

Servitec 35-95 with Touch
controller
15.12.2021 - Rev. D
Vacuum spray degassing
GB
Operating manual
Original operating manual

Contents
2 —English
Servitec 35-95 with Touch controller —01.04.2022
English
Contents
1Notes on the operating manual ......................................... 3
2Liability and guarantee....................................................... 3
3Safety................................................................................... 3
3.1 Explanation of symbols......................................................................3
3.2 Personnel requirements.....................................................................3
3.3Personal protective equipment ..........................................................3
3.4 Intended use ......................................................................................3
3.5 Inadmissible operating conditions .....................................................3
3.6 Residual risks.....................................................................................4
4Description of the device................................................... 4
4.1 Description.........................................................................................4
4.2 Overview............................................................................................4
4.3 Nameplate..........................................................................................5
4.4 Function .............................................................................................5
4.5 Scope of delivery ...............................................................................6
4.6 Optional equipment and accessories ................................................6
5Technical data..................................................................... 6
5.1 Electrical system................................................................................6
5.2 Dimensions and connections.............................................................6
5.3 Operation ...........................................................................................7
6Installation........................................................................... 7
6.1 Installation conditions ........................................................................7
6.1.1 Incoming inspection ...........................................................7
6.2 Preparatory work................................................................................7
6.3 Execution ...........................................................................................7
6.3.1 Fitting the add-on components ..........................................8
6.3.2 Installation location.............................................................8
6.3.3 Hydraulic connection..........................................................8
6.4 Switching and make-up variants........................................................9
6.4.1 Pressure-dependent "Magcontrol" make-up mode............9
6.4.2 Level dependent "Levelcontrol" make-up mode................9
6.5 Electrical connection..........................................................................9
6.5.1 Terminal plan, connection component.............................10
6.5.2 Terminal plan, operating unit ...........................................11
6.5.3 RS-485 interface ..............................................................11
6.6 Installation and commissioning certificate .......................................11
7Commissioning................................................................. 11
7.1 Checking the requirements for commissioning ...............................11
7.2 Setting the minimum operating pressure for Magcontrol ................12
8Controller........................................................................... 12
8.1 Operator panel .................................................................................12
8.2 Calibrating the touch screen ............................................................12
8.3 Modifying the controller's start routine .............................................13
8.4 Filling the device with water and venting .........................................14
8.5 Vacuum test .....................................................................................14
8.6 Use the device to fill the facility system with water..........................14
8.7 Starting Automatic mode..................................................................15
9Operation........................................................................... 15
9.1 Operating modes..............................................................................15
9.1.1 Automatic mode................................................................15
9.1.2 Manual mode....................................................................15
9.1.3 Stop mode ........................................................................16
9.1.4 Summer operation............................................................16
9.2 Restarting.........................................................................................16
10 Controller........................................................................... 16
10.1 Configuring settings in the controller ...............................................16
10.1.1 Customer menu................................................................16
10.1.2 Service menu....................................................................17
10.1.3 Default settings.................................................................17
10.1.4 Degassing programmes –overview.................................18
10.1.5 Setting degassing programmes .......................................18
10.2 Messages.........................................................................................19
11 Maintenance...................................................................... 21
11.1 Exterior leak test ..............................................................................21
11.2 Cleaning the dirt trap........................................................................21
11.3 Function test.....................................................................................21
11.4 Maintenance certificate ....................................................................22
11.5 Inspection.........................................................................................22
11.5.1 Pressure-bearing components .........................................22
11.5.2 Inspection prior to commissioning....................................22
11.5.3 Inspection intervals...........................................................22
12 Disassembly...................................................................... 22
13 Annex................................................................................. 23
13.1 Reflex Customer Service .................................................................23
13.2 Guarantee ........................................................................................23
13.3 Conformity and standards................................................................23
Servitec35-95 with Touch controller
15.12.2021- Rev. D

Notes on the operating manual
Servitec 35-95 with Touch controller —01.04.2022
English —3
1Notes on the operating manual
This operating manual is an important aid for ensuring the safe and reliable
functioning of the device.
The operating manual will help you to:
•avoid any risks to personnel.
•become acquainted with the device.
•achieve optimal functioning.
•identify and rectify faults in good time.
•avoid any faults due to improper operation.
•cut down on repair costs and reduce the number of downtimes.
•improve the reliability and increase the service life of the device.
•avoid causing harm to the environment.
Reflex Winkelmann GmbH accepts no liability for any damage resulting from
failure to observe the information in this operating manual. In addition to the
requirements set out in this operating manual, national statutory regulations and
provisions in the country of installation must also be complied with (concerning
accident prevention, environment protection, safe and professional work
practices, etc.).
This operating manual describes the device with basic equipment and interfaces
for optional equipment with additional functions. For optional equipment and
accessories, see chapter 4.6 "Optional equipment and accessories" on page 6 .

Notice!
Every person installing this equipment or performing any other work at
the equipment is required to carefully read this operating manual prior to
commencing work and to comply with its instructions. The manual is to
be provided to the product operator and must be stored near the
product for access at any time.
2Liability and guarantee
The device has been built according to the state of the art and recognised safety
rules. Nevertheless, its use can pose a risk to life and limb of personnel or third
persons as well as cause damage to the system or other property.
It is not permitted to make any modifications at the device, such as to the
hydraulic system or the circuitry.
The manufacturer shall not be liable nor shall any warranty be honoured if the
cause of any claim results from one or more of the following causes:
•Improper use of the device.
•Unprofessional commissioning, operation, service, maintenance, repair or
installation of the device.
•Failure to observe the safety information in this operating manual.
•Operation of the device with defective or improperly installed
safety/protective equipment.
•Failure to perform maintenance and inspection work according to
schedule.
•Use of unapproved spare parts or accessories.
Prerequisite for any warranty claims is the professional installation and
commissioning of the device.

Note!
Arrange for Reflex Customer Service to carry out commissioning and
annual maintenance, see chapter 13.1 "Reflex Customer Service" on
page 23 .
3Safety
3.1 Explanation of symbols
The following symbols and signal words are used in this operating manual.
DANGER
Danger of death and/or serious damage to health
•The sign, in combination with the signal word 'Danger', indicates
imminent danger; failure to observe the safety information will result in
death or severe (irreversible) injuries.
WARNING
Serious damage to health
•The sign, in combination with the signal word 'Warning', indicates
imminent danger; failure to observe the safety information can result in
death or severe (irreversible) injuries.
CAUTION
Damage to health
•The sign, in combination with the signal word 'Caution', indicates
danger; failure to observe the safety information can result in minor
(reversible) injuries.
ATTENTION
Damage to property
•The sign, in combination with the signal word 'Attention', indicates a
situation where damage to the product itself or objects within its vicinity
can occur.

Note!
This symbol, in combination with the signal word 'Note', indicates useful
tips and recommendations for efficient handling of the product.
3.2 Personnel requirements
Only specialist personnel or specifically trained personnel may install and
operate the equipment.
The electric connections and the wiring of the device must be executed by a
specialist in accordance with all applicable national and local regulations.
3.3 Personal protective equipment
Use the prescribed personal protective equipment as required (e.g. ear
protection, eye protection, safety shoes, helmet, protective clothing, protective
gloves) when working on the system.
Information on personal protective equipment requirements is set out in the
relevant national regulations of the respective country of operation.
3.4 Intended use
The device is used in facility systems for stationary heating and cooling circuits.
The devices may be used only in systems that are sealed against corrosion and
with the following water types:
•Non-corrosive.
•Chemically non-aggressive.
•Non-toxic.
Minimise the entry of atmospheric oxygen throughout the facility system and into
the make-up water.

Note!
Ensure the quality of the make-up water as specified by national
regulations.
–For example, VDI 2035 or SIA 384-1.

Note!
•To ensure fault-free operation of the system over the long-term,
glycols whose inhibitors prevent corrosion phenomena must
always be used for systems operating with water/glycol mixtures. It
must also be ensured that no foam is formed due to the
substances in the water. Otherwise this could endanger the entire
function of the vacuum spray pipe degassing as this can lead to
sedimentation in the vent pipe and therefore leaks.
•The specifications of the respective manufacturer are always
decisive for the specific properties and mixing ratio of the
water/glycol mixtures.
•Types of glycol must not be mixed and the concentration is
generally to be checked every year (see manufacturer
information).
3.5 Inadmissible operating conditions
The device is not suitable for the following applications:
•Mobile system operation.
•Outdoor operation.
•For use with mineral oils.
•For use with flammable media.
•For use with distilled water.

Note!
It is not permitted to make any modifications to the hydraulic system or
the circuitry.

Description of the device
4 —English
Servitec 35-95 with Touch controller —01.04.2022
3.6 Residual risks
This device has been manufactured to the current state of the art. However,
some residual risk cannot be excluded.
CAUTION
Risk of burns on hot surfaces
Hot surfaces in heating systems can cause burns to the skin.
•Wear protective gloves.
•Please place appropriate warning signs in the vicinity of the device.
CAUTION
Risk of injury due to pressurised liquid
If installation, removal or maintenance work is not carried out correctly, there
is a risk of burns and other injuries at the connection points, if pressurised
hot water or hot steam suddenly escapes.
•Ensure proper installation, removal or maintenance work.
•Ensure that the system is de-pressurised before performing installation,
removal or maintenance work at the connection points.
WARNING
Risk of injury due to heavy weight
The devices are heavy. Consequently, there is a risk of physical injury and
accidents.
•Use suitable lifting equipment for transportation and installation.
CAUTION
Risk of injury when upon coming into contact with glycol containing
water
Contact with glycol containing water in plant systems for cooling circuits can
result in irritation of the skin and eyes.
–Use personal protective equipment (safety clothing, gloves and
goggles, for example).
4Description of the device
4.1 Description
The device is a degassing and water make-up station for facility systems.
The following facility systems are applicable for the device:
•Facility systems with heating circuits.
•Facility systems with cooling circuits.
•Facility systems with solar circuits.
•Facility systems with process circuits.
The device fulfils two functions:
1. Degassing of water.
•Water from the facility system.
•Water from the make-up mains for the facility system.
It removes up to 90 % of the dissolved gases from the water. Malfunctions in the
facility system resulting from free or dissolved gases in the water are avoided.
2. Make-up with water for the facility system.
•Two make-up variants can be selected for the facility system.
–Magcontrol make-up variant: For facility systems with
expansion vessels.
–Levelcontrol make-up variant: For facility systems with
pressure maintaining stations.
The device provides the following safety features:
•Control of the pressure maintenance of the facility system
•Automatic make-up with water.
•No water circulation problems in the facility system.
•Reduction of corrosion damage by removal of oxygen from the water.

Note!
The device can only be operated at water temperatures up to a
maximum of 90 °C.

Note!
Operation and functioning at high system temperatures (>70°C):
If a vacuum is created, the boiling point of the medium reduces. This
property results in a change in volume of the medium in the vacuum
spray tube. If the medium boils, the pressure increases and counteracts
the vacuum created in the spray tube. Thanks to this characteristic, the
type of degassing changes from vacuum degassing to thermal
degassing. If the medium is boiling, the solubility of gases is almost
zero. Moreover, a higher pump flow rate does not automatically result in
a higher vacuum (at temperatures >70°C).
4.2 Overview
The unit overviews are only examples. Structure and functionality is the same for
the devices below.
Servitec 35 –60
Servitec 75 –95
1
Degassing valve "DV"
2
Vacuum gauge "PI"
3
Control Touch controller
4
2-way motor control valve "CD" upstream of vacuum spray tube
5
2-way motor control valve "WV" upstream of vacuum spray tube
6
Ball control ball valve "PV" downstream of pump "PU"

Description of the device
Servitec 35-95 with Touch controller —01.04.2022
English —5
7
Connection "WC" for the make-up
•Input for gas-rich water from the make-up
8
Connection "DC" for degassing
•Input for gas-rich water from the facility system
9
Connection "DC" for degassing
•Degassed water outlet
10
Pressure switch "PIS"
11
Pump "PU"
12
Insufficient water switch
13
Feed and drain cock "FD"
14
Main switch
15
Vacuum spray tube "VT"
4.3 Nameplate
The nameplate is attached below the screw cover of the controller. On it can be
found information about the manufacturer, the year of manufacture, the
manufacturing number and the technical data.
Information on the type plate
Meaning
Type
Device name
Serial No.
Serial number
Min. / max. allowable pressure PS
Minimum/maximum permissible
pressure
Max. allowable flow temperature of
system
Maximum permissible flow temperature
of the system
Min. / max. working temperature TS
Min./max. operating temperature (TS)
Year of manufacture
Year of manufacture
Max. system pressure
Max. system pressure
Min. operating pressure set up on
site
Minimum operating pressure, set on site
4.4 Function
The Servitec is suited for the degassing of water from the plant and make-up
water. It removes up to 90 % of the dissolved gases from the water. The
degassing operation uses timer-controlled cycles. A cycle comprises the
following phases:
•Inject and pump down to create a vacuum
The feed "DC" of gas-rich water from the system to the vacuum spray tube
"VT" has been opened. Depending on the requirement, partial flows of the
gas-rich system water and the make-up water are atomised in the vacuum
spray tube via the lines "DC" and "WC". As less water is injected into the
spray tube than is fed back into the system from the vacuum spray tube via
the pump "PU", a vacuum is formed in the spray tube. The pump "PU"
continues pumping down to create a vacuum until the water saturation
pressure is reached. The vacuum is indicated at the vacuum gauge "PI".
The large contact surface of the atomised water and the gas saturation
gradient to the vacuum result in degassing of the water. The pump returns
degassed water from the vacuum spray tube to the system where it again
begins to dissolve gases. There it is able to dissolve gases again.
•Discharge
The "PU" pump shuts off. The system continues to inject and degas water
in the "VT" vacuum spray tube. The water level in the vacuum spray tube
rises. The gases separated from the water are discharged via the "DV"
degassing valve.
•Idling time
The gas has been discharged, the Servitec will remain idling until the next
cycle is started.
Sequence of a degassing cycle in the vacuum spray pipe "VT"
Example: Cooling water system ≤ 30 °C, System pressure 1.8 bar, "DC" system
degassing in operation, "WC" make-up degassing closed.
1
Inject and pump down to create
a vacuum
3
Discharge
2
Inject and pump down to create
a vacuum
4
Idling time
Degassing
The entire degassing process is hydraulically synchronised by the "PV" motor
adjustment apparatus and the Servitec controller. The system monitors the
operating states and displays them at the Servitec controller. The controller
provides 3 different degassing programmes and 2 different make-up variants for
selection and setting.
Degassing programmes
The device controller regulates the degassing process. The controller monitors
the operating states and outputs them to the display.
The controller provides 3 different degassing programmes for selection and
adjustment:
•Continuous degassing
For continued degassing over several hours or days in a sequence of
degassing cycles without idling periods. This degassing programme must
be selected after commissioning and repairs.
•Interval degassing
This comprises a limited number of degassing cycles. There is an idling
time between the intervals. This degassing programme must be selected
for continuous operation.
•Make-up degassing
With this setting, the make-up water is degassed. A system degassing
does not occur.
Make-up variants
There are two make-up variants for the device. These are selected in the
controller and set for the device:
•Make-up variant Magcontrol.
For facility systems with expansion vessels. The pressure in the facility
system is monitored with the aid of the integrated pressure sensor in the
device. If the plant pressure falls below the calculated filling pressure,
water make-up is triggered.
•Make-up variant Levelcontrol.
For facility systems with pressure maintaining stations. The water level in
the expansion vessel of the pressure maintaining system is determined
with the "LIS" external pressure transducer. If the water level in the
expansion vessel falls, a signal is switched from the pressure maintenance
station to the Servitec to activate the make-up.
Servitec 35 - 95 with motorized ball valve

Technical data
6 —English
Servitec 35-95 with Touch controller —01.04.2022
1
Control line of a pressure maintenance station for requesting the
make-up in "Levelcontrol" mode
2
Signal line from the "PIS" pressure transducer for the "Magcontrol"
make-up variant
3
"DC" degassing line (degassed water)
4
"DC" degassing line (gas-rich water)
5
"WC" make-up line
6
Optional equipment and accessories see chapter 4.6 "Optional
equipment and accessories" on page 6
7
Control Touch controller
4.5 Scope of delivery
The scope of delivery is described in the shipping document and the content is
shown on the packing.
Immediately after receipt of the goods, please check the shipment for
completeness and damage. Please notify us immediately of any transport
damage.
Basic degassing equipment:
•Control of the Servitec.
•"DV" degassing valve, box-packaged.
•Plastic sleeve with operating manual and electric wiring diagram (attached
to the Servitec).
The Servitec is pre-assembled and shipped on a pallet.
4.6 Optional equipment and accessories
The following optional equipment and accessories are available for this device:
•Fillsoft/Fillsoft zero for softening/desalination of the make-up water from
the potable water supply system. Replacement of the softening and
desalination cartridges.
•Fillset for make-up with water
–Fillset with integrated backflow preventer, water meter, dirt trap, and
shut-ff for the "WC" make-up line
•Fillset Impulse with FQIR+ contact water meter for make-up with water.
–If the Fillset Impulse is installed, you can regulate the entire make-up
quantity and the soft water capacity of Fillsoft softening systems. The
operational reliability of the device is assured and prevents automatic
make-up during major water loss or small leaks.
•Fillset Compact for make-up
–Fillset Compact with integrated system separator, dirt trap, and shut-
off for the "WC" make-up line.
•Fillguard for conductivity monitoring
–If the Fillguard is fitted, the capacity of the Fillsoft Zero desalination
cartridge can be monitored based on the conductivity.
•Enhancements for the device controller.
–Various controller information can be queried via the RS-485
interface and it can also be used to communicate with control centres
or other devices, see chapter 6.5.3 "RS-485 interface" on page 11 .
•Bus modules for the communication with control centres.
•Profibus-DP.
•Ethernet.
•I/O module for standard communication.
•Modbus RTU
•Control Remote
•Gas discharge measurement for optimised degassing operation.

Note!
Separate operating manuals are supplied with accessories.
5Technical data

Note!
The following values apply for all systems:
–Permissible operating temperature of the device:
–Permissible inlet pressure for make-up:
–Make-up capacity:
–Separation level, dissolved gases:
–Separation level, free gases:
–Degree of protection:
90 °C
1.3 bar –6 bar
Up to 0.55 m³/h
≤ 90 %
100 %
IP 54
5.1 Electrical system
Type
Power output
(kW)
Power supply
(V / Hz/ A)
Fusing
(internal)
(A)
Number of RS-
485 interfaces
I/O module
Control Unit
(V, A)
Noise level
(dB)
35
0.85
230 / 50
10
2
Optional
230, 2
55
60
1.1
230 / 50
10
2
Optional
230, 2
55
75
1.1
230 / 50
10
2
Optional
230, 2
55
95
1.1
230 / 50
10
2
Optional
230, 2
55
5.2 Dimensions and connections
Type
Weight
(kg)
Height
(mm)
Width
(mm)
Depth
(mm)
Servitec input
connections
(system and make-
up)
Servitec output
connection
35
30
965
553
486
Internal thread ½ "
Internal thread 1 "
60
36
1150
600
486
Internal thread ½ "
Internal thread 1 "
75
41
1150
573
635
Internal thread ½ "
Internal thread 1 "
95
42
1150
573
635
Internal thread ½ "
Internal thread 1 "

Installation
Servitec 35-95 with Touch controller —01.04.2022
English —7
5.3 Operation
Type
System volume
(100% water)
(m³)
System volume
(50% water)
(m³)
Working pressure
(bar)
Permissible
operating gauge
pressure
(bar)
Setpoint overflow
valve
(bar)
Operating
temperature
(°C)
35
up to 220
up to 50
0.5 –2.5
8
–
>0 –90
60
up to 220
up to 50
0.5 –4.5
8
–
>0 –90
75
up to 220
up to 50
1.3 –5.4
10
–
>0 –90
95
up to 220
up to 50
1.3 –7.2
10
–
>0 –90
6Installation
DANGER
Risk of serious injury or death due to electric shock.
If live parts are touched, there is risk of life-threatening injuries.
•Ensure that the system is voltage-free before installing the device.
•Ensure that the system is secured and cannot be reactivated by other
persons.
•Ensure that installation work for the electric connection of the device is
carried out by an electrician, and in compliance with electrical
engineering regulations.
CAUTION
Risk of injury due to pressurised liquid
If installation, removal or maintenance work is not carried out correctly, there
is a risk of burns and other injuries at the connection points, if pressurised
hot water or hot steam suddenly escapes.
•Ensure proper installation, removal or maintenance work.
•Ensure that the system is de-pressurised before performing installation,
removal or maintenance work at the connection points.
CAUTION
Risk of burns on hot surfaces
Hot surfaces in heating systems can cause burns to the skin.
•Wear protective gloves.
•Please place appropriate warning signs in the vicinity of the device.
CAUTION
Risk of injury due to falls or bumps
Bruising from falls or bumps on system components during installation.
•Wear personal protective equipment (helmet, protective clothing,
gloves, safety boots).

Note!
Confirm that installation and start-up have been carried out correctly
using the installation, start-up and maintenance certificate. This action is
a prerequisite for the making of warranty claims.
–Have the Reflex Customer Service carry out commissioning and
the annual maintenance.
6.1 Installation conditions
6.1.1 Incoming inspection
Prior to shipping, this device was carefully inspected and packed. Damages
during transport cannot be excluded.
Proceed as follows:
1. Upon receipt of the goods, check the shipment for
•completeness and
•possible transport damage.
2. Document any damage.
3. Contact the forwarding agent to register your complaint.
6.2 Preparatory work
Condition of the delivered device:
• Check all screw fittings and electrical connections of the Servitec for proper
seating.
Tighten the screws and fittings as necessary.
Preparing the device installation:
•Frost-free, well-ventilated room.
•Ambient temperature > 0 to maximal 45 °C.
•Level, stable flooring with a drainage facility.
•Filling connection DN 15 to DIN 1988 -100/ -600 / DIN EN 1717.
•Electric connection 230 V~, 50/60 Hz, 16 A with upstream ELCB: Tripping
current 0.03 A.
The Servitec can be operated in two different modes for water make-up. When
installing the Servitec, note its position within the system:
•Pressure-dependent make-up of system water (Magcontrol).
–Install the Servitec in the vicinity of the expansion vessel.
•Level-dependent make-up of system water (Levelcontrol).
–Install the Servitec on the system side in the return upstream of the
return flow admixture.

Note!
Servitec make-up line.
–Use the Fillset system separator if the make-up line of the drinking
water mains is closed.
–The applicable guidelines and regulations of the country of
installation must be observed.

Note!
Comply with the Reflex planning directive.
–During planning, take into account that the working range of the
Servitec must be between the "pa" supply pressure and the "pe"
final pressure in the working range of the pressure maintenance
system.
6.3 Execution
ATTENTION
Damage due to improper installation
Additional device stresses may arise due to the connection of pipes or
system equipment.
•Ensure that pipes are connected (torque-free) from the device to the
system without them being stressed or strained.
•If necessary, provide support structures for the pipes or equipment.
ATTENTION
Property damage caused by leaks
Leaks in the connection pipes to the device can cause material damage to the
facility system.
• Use only connection pipes with appropriate resistance against the facility
system temperature.
In heating systems, preferably install the device in the return side.
–In this manner, you ensure that the device is operated within the
permissible pressure and temperature ranges.
–In systems with return admixtures or hydraulic switching points, the device
must be installed upstream of the admixture point to ensure degassing in
the "V" main flow volume at temperatures ≤ 90 °C.
The device is pre-wired and must be adapted for the local system conditions.
Complete the water-side connection to the system and the electric connection as
shown in the terminal diagram, see chapter 6.5 "Electrical connection" on page 9
.

Note!
During installation, pay attention to the operability of the valves and the
inlet options for the connecting lines.

Installation
8 —English
Servitec 35-95 with Touch controller —01.04.2022
6.3.1 Fitting the add-on components
Install the "DV" degassing valve (2) with the check valve (1) on the "VT" vacuum
spray tube. Check all screw fittings of the Servitec for proper seating.
6.3.2 Installation location
The Servitec is installed on the floor. Select the attachment means according to
the floor properties and the weight of the Servitec.

Note!
Consider a potential difference in head "hst" between the expansion
vessel and the device when calculating the "P0" minimum operating
pressure.
6.3.3 Hydraulic connection
6.3.3.1 Degassing line to the system
The device requires two "DC" degassing lines to the system. One degassing line
is intended for gas-rich water from the system, and the other one serves to return
the degassed water to the system. Shut-off devices for both degassing lines
have been pre-installed at the device. The connections of the degassing lines
must be made within the main flow volume of the facility system.
Device installation in a heating system –Pressure maintenance with
expansion vessel
1
"SV" safety valve
2
"EC" expansion line
3
"DC" degassing line (degassed water)
4
"DC" degassing lines (gas-rich water)
5
"WC" make-up line
6
Optional equipment and accessories see chapter 4.6 "Optional
equipment and accessories" on page 6 .
7
Servitec
8
Expansion vessel
The degassing lines into the system are to be installed near the connection point
of the "EC" expansion line. This ensures stable pressure conditions.
If you operate the device with pressure-dependent water make-up, you must
install the system near the diaphragm-type expansion vessel. This ensures that
the pressure in the diaphragm-type expansion vessel is monitored. In this case,
select the "Magcontrol" operating mode in the controller.

Note!
Ensure the integration in the "V" main flow volume when using switching
variants with hydraulic switching points and return admixtures.
–For switching and make-up variants, see chapter 6.4 "Switching
and make-up variants" on page 9 .
Installation detail of the "DC" degassing line
Connect the "DC" degassing lines as shown below.
•Ensure that particulate dirt cannot enter and thus create an overload of the
Servitec's "ST" dirt trap.
•Connect the degassing line for gas-rich water upstream of the degassing
line for degassed water in system direction of flow.
•The water temperature must be in the range > 0 °C –90 °C. The return
line side should be preferred for heating systems. This ensures the
permissible temperature range for degassing.
6.3.3.2 Make-up line
1
Servitec
3
"BT" system separator vessel
2
"WV" 2-way motorized ball
valve
4
"ST" dirt trap
For a water make-up via a "BT" mains disconnect receptacle, its bottom edge
must be at least 1000 mm above the "PU" degassing pump.
Various Reflex make-up variants, see chapter 4.6 "Optional equipment and
accessories" on page 6 .
If you do not connect the automatic water make-up, you must close the
connection of the "WC" make-up line with a R ½ " blanking plug and start up the
system in "Levelcontrol" mode.
For external water make-up, note the following conditions:
•Install at least one "ST" dirt trap with a mesh size ≤ 0.25 mm close
upstream to the "WV" 2-way motorized ball valve or use our Fillset.

Note!
When using an external system make-up, ensure that no Servitec fault
occurs as a result of different operating parameters.

Note!
Use a pressure reducer in the "WC" make-up line if the idle pressure
exceeds 6 bar.

Installation
Servitec 35-95 with Touch controller —01.04.2022
English —9
6.4 Switching and make-up variants
Select the make-up variant in the Customer menu of the device controller, see
chapter 10.1.1 "Customer menu" on page 16 .
Choose from one of the following make-up variants in the Customer menu:
•Pressure-dependent "Magcontrol" make-up.
–In a facility system with diaphragm expansion tank.
•Level-dependent "Levelcontrol" make-up.
–In a facility system with pressure maintaining station.
6.4.1 Pressure-dependent "Magcontrol" make-up mode
Example representation of a multi-tank system with hydraulic switching point and
a "MAG" diaphragm-type expansion vessel.
1
"MAG" expansion vessel
2
Servitec
3
Optional equipment and accessories see chapter 4.6 "Optional
equipment and accessories" on page 6
4
"WC" make-up line
The "Magcontrol" operating mode is set in the Customer menu of the Servitec
controller. This operating mode is used for plant systems with a diaphragm-type
expansion vessel. The make-up action depends on the pressure. The required
"PIS" pressure sensor is integrated in the Servitec. The "DC" degassing lines are
connected close to the diaphragm-type expansion vessel. In this way precise
pressure monitoring is enable for demand-matched make-up as.

Note!
Connect the degassing lines on the return side of the system upstream
of the hydraulic switching point. In this manner the permissible
temperature range of 0° - 90°C is adhered to.
6.4.2 Level dependent "Levelcontrol" make-up mode
Typical representation of Servitec 35 - 95 with motorized ball valves in a facility
system.
1
"PIS" pressure transducer
2
"DC" degassing line (degassed water)
3
"DC" degassing line (gas-rich water)
4
Optional equipment and accessories see chapter 4.6 "Optional
equipment and accessories" on page 6
5
"WC" make-up line
6
Servitec
7
"LIS" pressure pick-up
8
Pressure-maintaining station (compressor-controlled) with
expansion vessel
The "Levelcontrol" operating mode is set in the Customer menu of the device
controller. This operating mode is used for facility systems with pressure-
maintaining stations. The make-up with water depends on the filling level in the
expansion vessel of the pressure-maintaining station. The "LIS" pressure
transducer determines the filling level and sends this value to the controller of the
pressure maintenance station. The controller sends a 230 V signal to the device
controller when the filling level in the expansion vessel has fallen below the set
value.
Make-up with water is realised by regulating the motorized ball valve in the "WC"
make-up line. The device controller regulates the motor actuator of the motorized
ball valves. This ensures a controlled make-up with water and monitoring of the
make-up time and cycles.
6.5 Electrical connection
DANGER
Risk of serious injury or death due to electric shock.
If live parts are touched, there is risk of life-threatening injuries.
•Ensure that the system is voltage-free before installing the device.
•Ensure that the system is secured and cannot be reactivated by other
persons.
•Ensure that installation work for the electric connection of the device is
carried out by an electrician, and in compliance with electrical
engineering regulations.
For the electrical connection, you must differentiate between a connection
component and an operating component.
1
Connection unit
2
Covers of the operating unit (folding)
•RS-485 interfaces
•Pressure output
3
Operating unit (Control Touch controller)
4
Cable bushings
5
Covers of the connection unit (folding)
•Supply and fusing
•Floating contacts
•Aggregate connection
The following descriptions apply to standard systems and are limited to the
necessary user-provided connections.
1. Shut down the system and secure it against unintentional reactivation.
2. Remove the covers.
DANGER –electric shock! Risk of serious injury or death due to
electric shock. Some parts of the device's circuit board may still be live with
230 V even after the device has been physically isolated from the power
supply by pulling out of the mains plug. Before you remove the covers,
completely isolate the device controller from the power supply. Verify that
the main circuit board is voltage-free.

Installation
10 —English
Servitec 35-95 with Touch controller —01.04.2022
3. Insert a suitable screwed cable gland for the cable bushings at the rear of
the connection component. M16 or M20, for example.
4. Thread all cables to be connected through the cable glands.
5. Connect all cables as shown in the terminal diagrams.
–Connection unit, see chapter 6.5.1 "Terminal plan, connection
component" on page 10 .
–Operating unit, see chapter 6.5.2 "Terminal plan, operating unit" on
page 11 .
–When providing fusing for the appliance, note its connected load, see
chapter 5 "Technical data" on page 6 .
6. Install the cover.
7. Connect the mains plug to the 230 V power supply.
8. Activate the system.
The electrical connection is completed.
6.5.1 Terminal plan, connection component
1
Pressure
3
Fuses
2
Conductivity
Terminal
number
Signal
Function
Wiring
Supply
X0/1
L
Supply 230 V, maximum
16 A.
•Servitec 35-95
User
supplied
X0/2
N
X0/3
PE
Circuit board
13
NO
Dry-running protection
message (floating).
User,
optional
14
COM
22a
FB2a
COM
External make-up request.
–With Levelcontrol
setting.
Input 230 V signal via
L+N.
User,
optional
22b
FB2b
NO
23
NC
Group message (floating).
User,
optional
24
COM
25
NO
43
+24 V
•E1, digital input from
the contact water
meter.
Terminal 43+44.
E1, user
option
E2, factory
44
E1
•E2, insufficient water
switch.
Terminal 43+45.
45
E2
1
PE
Voltage supply.
Factory
2
N
3
L
4
Y1
WV make-up valve
Pre-wired
5
N
6
PE
Terminal
number
Signal
Function
Wiring
7
Y2
CD degassing control valve
Pre-wired
8
N
9
PE
10
Y3
---
---
11
N
12
PE
15
M1
"PU" pump
Pre-wired
16
N
17
PE
18
M2
---
---
19
N
20
PE
21
FB1
Voltage monitoring PU
pump
Pre-wired
27
M1
PU pump supply
Pre-wired
31
M2
---
---
35
+18V
Analogue input conductivity
Lf.
User,
optional
36
GND
37
AE
38
Shielding
39
+ 18 V (blue)
Analogue input "PIS"
pressure measuring.
–For pressure
indication and make-
up with the
"Magcontrol" setting.
Pre-wired
40
GND
41
AE (brown)
42
Shielding (black)
51
GND
---
---
52
+24 V (supply)

Commissioning
Servitec 35-95 with Touch controller —01.04.2022
English —11
Terminal
number
Signal
Function
Wiring
53
0–10V (correcting
variable)
54
0–10V (feedback)
55
GND (black)
Control ball valve"PV"
–For regulating the
hydraulic adjustment
of degassing.
Pre-wired
56
+24 V (supply)
(red)
57
0–10V (correcting
variable) (white)
58
0–10V (feedback)
(orange)
6.5.2 Terminal plan, operating unit
1
RS -485 networking
2
RS -485 module
3
I/O interface
4
SD card
5
10 V supply
6
Analogue outputs for pressure and conductivity
7
Battery compartment
8
Anybus module slot
9
Terminators RS-485 (dip switch)
10
Terminators RS-485 (dip switch)
Terminal
number
Signal
Function
Wiring
1
A
RS-485 interface.
S1 networking.
---
2
B
3
GND S1
4
A
RS-485 interface.
S2 modules: Extension or
communication module.
User supplied
5
B
6
GND S2
7
+5 V
I/O interface: Interface to the
main board
Factory
8
R × D
9
T × D
10
GND IO1
15
10 V~
10 V supply.
Factory
16
17
FE
18
PE (shield)
Analogue output: Pressure.
Standard 4 –20 mA.
(Optional 2 –10 V)
User supplied
19
Pressure
20
GNDA
21
LF
Analogue output conductivity Lf.
User supplied
22
GNDB
6.5.3 RS-485 interface
Use the S2 RS-485 interface to retrieve all controller data and to enable the
communication with control centres or other devices.
–S2 interface
•"PIS" pressure.
•Operating modes of the "PU" pump.
•Values of the "FQIRA +" contact water meter.
•All messages, see chapter 10.2 "Messages" on page 19 .
•All entries in the fault memory.
The following accessories are available for interface communication.
–Bus modules
•Profibus-DP.
•Ethernet.
•Optional I/O module.
•Modbus RTU.
6.6 Installation and commissioning certificate
Data shown on the type plate:
P0
Type:
PSV
Manufacturing number:
This device has been installed and commissioned in accordance with the
instructions provided in the operating manual. The settings in the controller
match the local conditions.

Note!
When any factory-set values of the device are changed, you must enter
this information in the Maintenance certificate, see chapter 11.4
"Maintenance certificate " on page 22 .
For the installation
Place, date
Company
Signature
For the commissioning
Place, date
Company
Signature
7Commissioning
CAUTION
Risk of burns on hot surfaces
Hot surfaces in heating systems can cause burns to the skin.
•Wear protective gloves.
•Please place appropriate warning signs in the vicinity of the device.

Note!
Confirm that installation and start-up have been carried out correctly
using the installation, start-up and maintenance certificate. This action is
a prerequisite for the making of warranty claims.
–Have the Reflex Customer Service carry out commissioning and
the annual maintenance.
7.1 Checking the requirements for commissioning
The Servitec will be ready for initial commissioning when the tasks described in
the "Installation" chapter have been completed.
•The Servitec has been mounted.
•The connections of the Servitec to the system have been created and plant
system pressure maintenance is operational.
–Degassing line to the facility system.
–Degassing line from the facility system.
•The water-side connection of the Servitec to the make-up has been
created and is operational, if automatic make-up is required.
•The connection pipes of the Servitec have been purged and cleaned of
welding residue and dirt before commissioning.
•The entire facility system is filled with water and all gases have been
vented in order to ensure a circulation through the entire system.
•The electrical connection has been created according to applicable
national and local regulations.

Controller
12 —English
Servitec 35-95 with Touch controller —01.04.2022
7.2 Setting the minimum operating pressure for Magcontrol
The "p0" minimum operating pressure is determined by the location of the
Servitec.
Description
Calculation
pst
Static pressure
= static head (hst)/10
p0
Minimum operating pressure
= pst + 0.2 bar (recommended)
pa
Initial pressure (cold water filling
pressure)
= p0+ 0.3 bar
pe
Final pressure
≤ pSv - 0.5 bar (for pSv ≤ 5.0
bar)
pSv
Safety valve actuating pressure
= p0+ 1.2 bar (for pSv ≤ 5.0
bar)
The calculation of the minimum operating pressure can be directly calculated
and saved during initial commissioning using the Reflex Control Smart app for
configuration. Please always check the correct inlet pressure of the expansion
vessel in the system. Proceed as follows:
1 In the app, set the controller to "Magcontrol".
2. Determine the "P0" minimum operating pressure of the device relative to
the "p0" initial pressure of the expansion vessel.
•The device is installed at the same level as the expansion vessel
(∆hst = 0).
–P0= p0*
•The device is installed at a lower level than the expansion vessel.
–P0= p0 + ∆hst/10*
•The device is installed at a higher level than the expansion
vessel.
–P0= p0 - ∆hst/10*
* p0 in bar, ∆hst in m

Note!
The safety valve actuating pressure must always be observed for the
target value of the Servitec
(see calculation formula).

Note!
Avoid dropping below the minimum operating pressure. Vacuum,
vaporisation and the formation of vapour bubbles are thus excluded.
8Controller
8.1 Operator panel
1
Message line
8
Display value
2
"▼"/ "▲" buttons
•Set digits.
9
"Manual mode" button
•For function tests.
3
""/"" buttons
•Select digits.
10
"Stop mode" button
•For commissioning.
4
"OK" button
•Confirm/acknowledge
input.
•Browse in the menu.
11
"Automatic mode" button
•For continuous operation.
5
"Up" and "Down" scroll bar
•"Scroll" in the menu.
12
"Set-up menu" button
•For setting parameters.
•Fault memory.
•Parameter memory.
•Display settings.
•Software version
information.
6
"Scroll back" button
•Cancel.
•Page back to the main
menu.
7
"Display help texts" button
•Opens help texts.
13
"Info menu" button
•Displays general
information.
8.2 Calibrating the touch screen
You can calibrate the touch screen when touching the desired buttons does not
work satisfactorily.
1. Switch the device off at the main switch.
2. Touch and hold the touch field with your finger.
3. Switch on the main switch while touching the touch field.
–When starting the program, the controller automatically switches to
the "Update/Diagnostics" function.
4. Touch the "Touch calibration" button.
5. Touch the displayed crosses on the touch screen after each other.
6. Switch the device off and on again at the main switch.
The touch screen is fully calibrated.

Controller
Servitec 35-95 with Touch controller —01.04.2022
English —13
8.3 Modifying the controller's start routine
The start routine is used to set the parameters for device commissioning. It
commences with the first switching on of the controller and can only be set once.
The following parameter changes or checks are carried out from the customer
menu, see chapter 10.1.1 "Customer menu" on page 16 .
A three-digit PM code is assigned to the setting options.
Step
PM code
Description
1
(00X)
Select the language
2
(00X)
Remember: Prior to installation and commissioning,
read the operating manual!
3
(00X)
Device type information
4
(00X)
Select the make-up variant
5
(00X)
Set the safety valve actuation pressure
6
(00X)
For Magcontrol variant only: Set the minimum
operating pressure PO
Otherwise, continue from step 7
7
(00X)
Set the time
8
(00X)
Set the date
9
(00X)
End of the start routine. The stop mode is active.
The system automatically displays the first page of the start routine when you
switch on the device for the first time:
1. Select the required language and conform your entry with "OK".
–Select the corresponding language.
2. Prior to commissioning, read the operating manual in full and check for
proper assembly.
3. Confirm your entries via the "OK" button.
–The start routine moves to the next page.
4. Select the required Make-up variant and conform your entry with "OK".
–For calculation of the make-up variant, see chapter 6.4 "Switching
and make-up variants" on page 9 .
5. Set the safety valve actuating pressure and conform with "OK".

Note!
This step 6 only applies to the Magcontrol make-up variant.
6. Select the calculated minimum operating pressure and conform with "OK".
–For calculation of the minimum operating pressure, see chapter 7.2
"Setting the minimum operating pressure for Magcontrol" on page 12
.
7. Set the time. The time of an alarm will be stored in the controller's fault
memory.
–Use the "Left" and "Right" buttons to select the display value.
–Use the "Up" and "Down" buttons to change the display value.
–Confirm your entries with "OK".
8. Set the date. The date of an alarm will be stored in the controller's fault
memory.
–Use the "Left" and "Right" buttons to select the display value.
–Use the "Up" and "Down" buttons to change the display value.
–Confirm your entries with "OK".
9. Press "OK" to conclude the start routine.

Note!
After successful conclusion of the start routine, you are in Stop mode.
Do not yet switch to Automatic mode.

Controller
14 —English
Servitec 35-95 with Touch controller —01.04.2022
8.4 Filling the device with water and venting
1
Vacuum gauge "PI"
5
Pump "PU"
2
Degassing valve "DV"
WC
Make-up pipe
3
Feed and drain cock "FD"
DC
Degassing lines
4
"AV" venting screw
1. Use the facility system to fill the Servitec.
–After you have opened the "DC" ball valves, the vacuum spray tube
will autonomously fill if the facility system provides sufficient water.
2. Optional
–Use the feed and drain cock (3) to fill water into the Servitec.
–Connect a hose at the feed and drain cock (3) of the "VT" vacuum
spray pipe.
3. Fill the vacuum spray pipe with water.
–Air escapes via the degassing valve (2) and the water pressure can
be read at the vacuum gauge (1).
Vent the pump:
4. Turn the venting screw (1) until air or a water/air mixture escapes.
5. If required, use a screwdriver to rotate the pump at the fan wheel of the
pump motor.
CAUTION –Risk of injury due to pump start-up! Hand injury due to a
pump start-up. Switch the pump to a zero-volts state before turning the
pump motor at the fan wheel with a screwdriver.
CAUTION –Device damage. Pump damage due to a pump start-up.
Switch the pump to a zero-volts state before turning the pump motor at the
fan wheel with a screwdriver.
–Water/air mixtures are removed from the pump.
6. Re-tighten the venting screw when only water escapes.
7. Close the feed and drain cock.
Filling and venting is concluded.

Note!
The "PU" pump must not be switched on when the Servitec is filled with
water.

Note!
Do not fully unscrew the venting screw. Wait until air-free water appears.
Repeat the venting process until the "PU" pump is fully vented.
8.5 Vacuum test
Perform the vacuum test to ensure the proper functioning of the device.
1 Close the ball valve (1) with the dirt trap of the "DC" feed line to the spray
pipe. The second ball valve (2) in the feed line from the "DC" pump to the
system remains open.
2 Generate a vacuum in manual mode of the controller.
•Switch to Manual mode.
–For information about controller operation, see chapter 8.1
"Operator panel" on page 12 .
–For more information about Manual mode, see chapter 9.1.2
"Manual mode" on page 15 .
3 Use "Circulate" to activate continuous degassing until the vacuum gauge
indicates a stable vacuum.
•Note the vacuum indicated on the vacuum gauge.
4 After 10 minutes, check again the "PI" vacuum gauge (1). The pressure
must not change. If the pressure has increased, check the device for leaks.
•All screw connections at the "VT" vacuum spray pipe.
•The "DV" degassing valve at the "VT" vacuum spray pipe.
•The venting screw at the "PU" pump.

Note!
Repeat steps 2 to 4 until no further pressure rise is observed.
5 After the vacuum test has been concluded successfully, open the ball valve
with dirt trap.
6 If the controller displays the "Insufficient water" error message,
acknowledge the message with "OK".
The vacuum test is completed.

Note!
The obtainable vacuum corresponds to the saturation pressure at the
existing water temperature.
•At 10 °C, a vacuum of approximately -1 bar can be obtained.
8.6 Use the device to fill the facility system with water
Optionally the device can be used to fill the facility system with water.
These prerequisites must be met:
•Facility system with a water content of less than 3000 litres.
•Facility system with pressurisation via a static expansion vessel.
Proceed as follows:
1. Open the "WC" make-up line.
–Open all shut-off devices between the make-up connection the
vacuum spray pipe.
2. Set the controller to "Magcontrol".
–For the "Magcontrol" make-up variant, see chapter 10.1.1 "Customer
menu" on page 16 .
3. Switch the controller to Manual mode.
–For Manual mode, see chapter 9.1.2 "Manual mode" on page 15 .
4. Touch "Open" in Manual mode.

Operation
Servitec 35-95 with Touch controller —01.04.2022
English —15
–The controller calculates the required filling pressure and the system
is filled with water. As soon as the filling pressure has been attained,
the controller automatically stops the filling process.
If the maximum filling time (10 hours by default) is exceeded, the system aborts
the make-up process with an error message. Upon detecting the cause of the
fault message, press "OK" on the controller's operator panel to acknowledge the
fault message. Upon eliminating the fault, continue with filling the system. After
filling, vent the system to ensure circulation throughout the entire system.

Note!
Monitor the system for the entire automatic filling process.

Note!
Fault messages, see chapter 10.2 "Messages" on page 19

Note!
Filling the system with water is not part of the deliverables of the Reflex
Customer Service.
8.7 Starting Automatic mode
During commissioning, remove all free and dissolved from the facility system.
•The "Continuous degassing" degassing programme is activated in
Automatic mode. Free and dissolved gases are removed from the facility
system.
Continuous degassing with a pre-set time of 24 hours is stored in the
Customer menu.
•Set the time for continuous degassing. The time depends on the device
type and the facility volume.
–Time reference values, see chapter 5 "Technical data" on page 6 .
•Set the time in the Customer menu.
–Settings in the Customer menu, see chapter 10.1.1 "Customer menu"
on page 16 .
Subsequent to the continuous degassing, the controller automatically switches to
"interval degassing".
Start Automatic mode to complete the commissioning process. These
prerequisites must be met for starting Automatic mode:
•System and device are filled with water.
•Servitec and the facility system are vented.
–If necessary, repeat the "Filling the device with water" process see
chapter 8.4 "Filling the device with water and venting" on page 14 .
To start the Automatic mode, proceed as follows:
•Ensure that the minimum working pressure is available.
•Touch the "AUTO" button.

Notice!
The "ST" dirt trap in the "DC" degassing line must be cleaned after the
expiry of the continuous degassing time at the latest, see chapter 11.2
"Cleaning the dirt trap" on page 21 .

Note!
The commissioning process is now concluded.
9Operation
9.1 Operating modes
9.1.1 Automatic mode
Activate Automatic mode. Automatic mode is continuous device operation.
The following functions are active in Automatic mode:
•Facility and make-up water degassing.
•Automatic make-up with water.
–Additional equipment for the make-up is available, see chapter 4.6
"Optional equipment and accessories" on page 6 .
The device controller monitors the functions. Faults are displayed and evaluated.
To start the Automatic mode, proceed as follows:
•Touch the "AUTO" button.
Select a degassing programme for Automatic mode. The Customer menu
provides three different degassing programmes for selection, see chapter 10.1.4
"Degassing programmes –overview" on page 18 .
•Continuous degassing.
•Interval degassing.
•Degassing the make-up water.
For selecting the degassing programmes, see chapter 10.1.5 "Setting degassing
programmes" on page 18 .
The controller displays the selected degassing programme in the message line.
9.1.2 Manual mode
Manual mode enables you to select the following For performing a test run and
service tasks:
•2-way motorized ball valve for degassing the system and the make-up
water "WV" and "CD"
–Manual actuator for opening or closing.
•Pump.
–For switching the pump on and off.
•2-way motorized ball valve (PV) in the line downstream of the pump
–Manual actuator for opening or closing.
•Filling.
–Make-up degassing is activated.
–For filling facility systems with pressure-dependent water make-up
"Magcontrol".
•Circulation.
–Activates continuous degassing of the facility water without time limit.
–For vacuum test during commissioning.
WV
2-way motorized ball valve in the make-up line
CD
2-way motorized ball valve in the degassing line from the system to
the Servitec
PU
Pump
PV
2-way motorized ball valve in the degassing line from the Servitec to
the system
You have the option to simultaneously switch multiple functions and to test them
in parallel. Switch the function on and off by touching the corresponding button.
•The button is highlighted green: The function is switched off.
•Press the desired button.
•The button is highlighted blue: The function is switched on.
Proceed as follows:
1. Press "Manual mode".
2. Select the desired function:
• 2x 2-way motorized ball valve in the make-up line (WV) and the
degassing line from the system to the Servitec (CD)
•Pump (PU)
•2-way motorized ball valve in the the degassing line (PV)
•Fill (PV opens if PU is active)
•Circulate
3. Press "AUTO" to deactivate Manual mode.
•Automatic mode is activated.

Controller
16 —English
Servitec 35-95 with Touch controller —01.04.2022

Note!
Manual operations cannot be performed if safety-relevant parameters
would be exceeded.
–Switching is blocked if safety-relevant settings would not be
complied with.
9.1.3 Stop mode
Except for the display of information, the device is non-functional in Stop mode.
Function monitoring is stopped.
The following functions are deactivated:
•The pump is switched off.
•The 2-way motorized ball valve in the degassing line from the Servitec to
the system (PV) is closed.
•The 2-way motorized ball valve in the make-up line (WV) is closed.
•The 2-way motorized ball valve in the degassing line from System to the
Servitec (CD) is closed.
To start Stop mode operation, proceed as follows:
•Touch "STOP".

Note!
The system returns an alarm if the Stop mode is activated for more than
4 hours.
–If "Volt free contact?" in the Customer menu is set to "Yes", the
system outputs the alarm to the group alarm contact.
9.1.4 Summer operation
If you have placed the facility system circulating pumps out of service during the
summer, no degassing of the plan system water occurs.
Proceed as follows:
•In this case, use the Customer menu to select the "Make-up degassing"
degassing programme.
•After Summer, select the "Interval degassing" degassing programme in the
Customer menu or "Continuous degassing", if required.

Note!
For a detailed description of the selection of degassing programmes,
see chapter 10.1.5 "Setting degassing programmes" on page 18 .
9.2 Restarting
CAUTION
Risk of injury due to pump start-up
Hand injuries may occur when the pump starts up if you turn the pump motor
at the impeller using a screwdriver.
•Switch the pump to a zero-volts state before turning the pump at the
fan wheel with a screwdriver.
ATTENTION
Device damage due to pump start-up
Pump damage may occur when the pump starts up if you turn the pump
motor at the impeller using a screwdriver.
•Switch the pump to a zero-volts state before turning the pump at the
fan wheel with a screwdriver.
After an extended device standstill time (the device is disconnected from the
power or in Stop mode), the pump may jam. For this reason, use a screwdriver
to rotate the pump at the fan wheel of the pump motor before restarting.

Note!
In device automatic mode, jamming of the pump is prevented by a
forced start (after 24 hours).
10 Controller
10.1 Configuring settings in the controller
You can configure the controller settings regardless of the currently selected and
active operating mode.
10.1.1 Customer menu
10.1.1.1 Customer menu –overview
Use the Customer menu to correct or determine system-specific values. In the
course of initial commissioning, the factory settings must be adjusted for the
system-specific conditions.

Note!
For a description of the operation, see chapter 8.1 "Operator panel" on
page 12 .
A three-digit PM code is assigned to the setting options
PM
code
Description
001
Select the language
002
Set the time
003
Set the date
004
Select the system type
•Levelcontrol
•Magcontrol
005
Set the P0minimum operating pressure, see chapter 7.2 "Setting
the minimum operating pressure for Magcontrol" on page 12 .
006
Set the actuating pressure for the system safety valve.
–The actuating pressure protects the device.
Degassing ˃
012
•Degassing programme
•Continuous degassing
•Interval degassing
•Run-on degassing
013
•Continuous degassing time
Make-up >
023
•Maximum make-up time …min.
024
•Maximum make-up cycles … /2 h.
•Frequency of make-up cycles in 2 hours.
024
•Make-up pressure
–Standard = Make-up pressure ˃2.3 bar.
–Setting range 1.3 –2.3 bar.
–< 1.3 bar.
027
•With contact water meter "Yes/'No".
–If "Yes", continue with 028.
–If "No", continue with 007.
028
•Reset make-up quantity "Yes/No".
–If "Yes", reset to "0".
029
•Maximum make-up quantity ... l
030
•Water treatment "Softening / Desalination / None".
–If "Softening", continue with 031.
–If "Desalination", continue with the next point
–If "None", continue with 007.
With conductivity monitoring "Yes/'No".
031
•Shut off make-up "Yes/No" (if water capacity is exhausted).

Controller
Servitec 35-95 with Touch controller —01.04.2022
English —17
PM
code
Description
032
•Soft water capacity ... l
–Calculation required before input.
•Fillsoft I + softening:
Soft water capacity = 6000 l / hardness reduction.
•Fillsoft I + desalination:
Soft water capacity = 3000 l / hardness reduction.
•Fillsoft II + softening:
Soft water capacity = 12000 l / hardness reduction.
•Fillsoft II desalination:
Soft water capacity = 6000 l / hardness reduction.
033
•Hardness reduction … °dH = GHactual –GHtarget
–Can be called when softening or desalination is active.
–Calculate the required reduction in overall hardness
GH before input.
034
•replacement interval… months (for softening cartridges
according to manufacturer).
007
Maintenance interval… months
008
Floating contact
•Message selection >
•Message selection: only messages marked with "√"
are output.
•All messages: All messages are output.
Fault memory > History of all messages
Parameter memory > History of parameter input
Display settings > Brightness, screen saver
Information >
•Position of the "PV" 2-way motorized ball valve at the
pressure side of the pump.
–Position in %
•Software version
10.1.1.2 Setting the customer menu - "Time" example
The setting of system-specific values is explained below using the setting of the
time as example.
To adjust the system-specific values, proceed as follows:
1. Press "Settings".
–The controller switches to the setting area.
2. Press "Customer >".
–The controller opens the Customer menu.
3. Press the required area.
–The controller switches to the selected area.
–Use the scroll bar to navigate through the list.
4. Set the system-specific values for the individual areas.
•Use the "Left" and "Right" buttons to select the display value.
•Use the "Up" and "Down" buttons to change the display value.
•Confirm your entries with "OK".
–Press "i" to display a help text for the selected area.
–Press "X" to cancel your input without saving the new settings. The
controller automatically opens again the list.
10.1.2 Service menu
This menu is protected with a password. It can be accessed only by the Reflex
Customer Service. A partial summary of the settings stored in the Service menu
is proved in the Chapter Default settings.
10.1.3 Default settings
The device controller is shipped with the following default settings. Use the
Customer menu to adjust these values to local conditions. In specific cases, it is
possible to further adjust the values in the Service menu.
Customer menu
Parameter
Setting
Remarks
Language
EN
Display language
Time
Date
Servitec
Magcontrol
For systems with diaphragm-
type expansion vessel
Minimum operating
pressure p0
1.5 bar
Only Magcontrol
Safety valve, pressure
3.0 bar
Actuating pressure of the
system’s heat generator safety
valve
Degassing
Degassing programme
Continuous
degassing
Continuous degassing
time
24 hours
Make-up
Maximum make-up
quantity
0 Litres
Only if controller with "With
water meter yes"
Maximum make-up time
20 minutes
Magcontrol and Levelcontrol
Maximum make-up cycles
3 cycles within
2 hours
Magcontrol and Levelcontrol
Softening (only if "Water treatment with Softening")
Shut off make-up
No
In the case of soft water
residual capacity = 0
Hardness reduction
8°dH
= Target –Actual
Soft water capacity
0 Litres
Attainable water capacity
Cartridge replacement
18 months
Replace cartridge
Desalination (only if "Water treatment" with Desalination")
Conductivity monitoring
No
Shut off make-up
No
In the case of soft water
residual capacity = 0
Hardness reduction
8°dH
= Target –Actual

Controller
18 —English
Servitec 35-95 with Touch controller —01.04.2022
Parameter
Setting
Remarks
Soft water capacity
0 Litres
Attainable water capacity
Cartridge replacement
18 months
Replace cartridge
Next maintenance
12 months
Time left to the next due
maintenance
Volt-free contact
YES
Only the messages marked in
the "Messages" list
Service menu
Parameter
Setting
Remarks
Make-up
Pressure differential,
"NSP" make-up
0.1 bar
Only Magcontrol
Pressure differential,
filling pressure PF –P0
0.2 bar
Only Magcontrol
Maximum filling duration
10 h
Only Magcontrol
Degassing
Idling times between
degassing intervals
10 hours
Idling times between the
degassing intervals
Number of degassing
cycles for each interval
n = 8
Number of degassing cycles in
one interval
Daily start
08:00 h
Start of the daily degassing
intervals
10.1.4 Degassing programmes –overview
You can choose between 3 degassing programs:
Continuous degassing
•Usage:
–For device commissioning.
–For degassing of the water after a device or facility system repair.
•Activation:
–An automatic activation occurs after completion of the start routine
during initial commissioning.
•Times:
–The time can be set in the Customer menu.
–The default setting is 24 hours. Subsequently, the system
automatically switches to Interval degassing.
In continuous degassing, the degassing cycles are sequentially performed for 24
hours.
Interval degassing
•Usage:
–For continuous operation of the device.
•Activation:
–Automatic activation occurs after the ending of continuous
degassing.
•Times:
–8 degassing cycles per interval is set in the Service menu.
–After 8 intervals there is an idling time of 12 hours.
–The times for interval degassing are stored in the Service menu.
–The daily start of interval degassing is at 8:00 a.m.
Interval degassing is preset in the customer menu as the default setting.
Make-up degassing
•Usage:
–For gas-rich water from the make-up.
–For summer operation when the circulating pumps of the facility
system are shut down, see chapter 9.1.4 "Summer operation" on
page 16 .
–If the facility system water is not to be degassed.
•Activation:
–Automatic activation occurs at every water make-up.
•During continuous degassing.
•During interval degassing.
•Times:
–The make-up water is degassed for as long as it is supplied, see
chapter 10.1.1 "Customer menu" on page 16 .

Note!
Manual activation of the degassing program takes place in the customer
menu.
10.1.5 Setting degassing programmes
1. Press "Settings".
–The controller switches to the setting area.
2. Press "Customer >".
–The controller opens the Customer menu.
3. Press "Degassing >".
–The controller switches to the selected area.
–Use the scroll bar to navigate "up" and "down" through the list.
4. Press "(012) Degassing programme".
–The controller opens the list of degassing programmes.
5. To select a menu item, press the "Up" or "Down" scroll bar until this menu
item is displayed.
•Press the desired button.
–"Continuous degassing" is selected in this example.
–Interval degassing is deactivated.
–Make-up degassing is deactivated.
•Confirm your selection with "OK".
Continuous degassing is activated.

Controller
Servitec 35-95 with Touch controller —01.04.2022
English —19
6. Press "(013) Time, continuous degassing".
7. Set the time for continuous degassing.
•Use the "Left" and "Right" buttons to select the display value.
•Use the "Up" and "Down" buttons to change the display value.
•Confirm your entries with "OK".
The time for continuous degassing is set.
–Press "i" to display a help text for the selected area.
–Press "X" to cancel your input without saving the new settings. The
controller automatically opens again the list.
10.2 Messages
The messages indicate impermissible deviations from the normal operating state
of the Servitec. They are output either via the RS-485 interface or via two floating
message contacts.
The controller displays the messages with a help text. By selecting the fault
memory in the Customer menu, you display the last 24 messages. Message
causes can be eliminated by the operator or a specialist workshop. If required,
please contact the Reflex Customer Service.

Note!
Messages identified with "OK" must be confirmed with the "OK" button
on the display. The device operation is otherwise interrupted. The
readiness for operation is maintained for all other messages. They are
displayed.

Note!
If necessary, you can set the output of messages via a floating contact
in the Customer menu.
To reset a fault message, proceed as follows:
1. Touch the display.
–The current fault messages are displayed.
2. Touch a fault message.
–The system displays the possible causes for the fault.
3. When the fault is eliminated, confirm the fault with "OK".
ER
Code
Alarm
Causes
Remedy
Alarm
reset
01
Minimum pressure
For "Magcontrol" setting only.
•Set value not reached
•Water loss in the system.
•Pump fault.
•Expansion vessel defective.
•Check set value in the customer or service menu.
•Check water level.
•Check pump.
•Check expansion vessel.
–
02.1
Low water
Dry run protection: Low water switch
•Defective.
•Not cabled.
•Triggered for too long.
•Check low water switch.
•Open the degassing line.
•Clean the dirt trap.
•Replace the degassing valve.
"OK"
02.2
Low water
Low water switch has actuated too often.
•Clean the dirt trap.
•Replace the degassing valve.
"OK"
04.1
Pump
Pump disabled.
•Pump jammed.
•Pump motor defective.
•Fuse defective.
•Rotate the pump with screwdriver.
•Electrically test the pump motor
•Replace the 10 A fuse.
"OK"
06
Make-up time
•Set value exceeded.
•Water loss in the system.
•Make-up line not connected.
•Make-up output insufficient.
•Check set value in the customer or service menu.
•Check water level.
•Connect make-up line.
"OK"
07
Make-up cycles
Continuous water loss in the system.
•Check set value in the customer or service menu.
•Seal the leakage in the system.
"OK"
08
Pressure
measurement
Controller receives incorrect signal.
•Check/connect the plug connection at the pressure
transmitter.
•Check the cable for damage.
•Check the pressure sensor.
"OK"

Controller
20 —English
Servitec 35-95 with Touch controller —01.04.2022
ER
Code
Alarm
Causes
Remedy
Alarm
reset
10
Maximum pressure
For "Magcontrol" setting only.
•Set value exceeded.
•Check set value in the customer or service menu.
•Set the actuating pressure of the safety valve.
"OK"
11
Make-up quantity
"With water meter" must be activated in the Customer menu.
•Set value exceeded.
•Severe water loss in the system.
•Check set value in the customer or service menu.
•Check the water loss and correct, if necessary.
"OK"
12
Filling time
Set value for the maximum filling duration has been
exceeded.
•Check set value in the customer or service menu.
•Check the water loss and correct, if necessary.
"OK"
13
Filling volume
Set value exceeded
•Check set value "Max. Fill Contact (128)" in the service
menu.
•Check the water loss and correct, if necessary.
"OK"
14
Discharge time
•Set value exceeded.
•"DC" degassing line closed.
•Dirt trap clogged.
•Check set value in the customer or service menu.
•Open the degassing line.
•Clean the dirt trap.
"OK"
15
Make-up valve
Contact water meter measures without make-up request.
Check the 2-way motor ball valve (WV) for leak tightness.
"OK"
16
Power failure
No voltage supply available.
Connect to voltage supply.
–
18
Parameter
Setting parameter not entered correctly.
Check setting parameter and correct if necessary.
–
19
Stop ˃4 hours
Longer than 4 hours in stop mode.
Set the controller to Automatic mode.
–
20
Maximum make-up
quantity
Set value exceeded.
Reset the "Make-up quantity" meter in the Customer menu.
"OK"
21
Maintenance
recommended
Set value exceeded.
Carry out maintenance.
"OK"
22
Blow-off time
Blow-off time outside the set value. (Only if appropriate
sensors are used.)
Check set value in the Customer or Service menu.
"OK"
24
Water treatment
•Water capacity set value exceeded.
•Time interval for replacement of the cartridge
exceeded.
•Replace water treatment cartridge.
•Confirm cartridge replacement in the customer menu by
pressing the "OK" button twice in the "Make-up" menu →
"Soft water capacity (032)"
–
25
Datalogger
•No SD card inserted
•The SD card is write-protected
•The SD card has not been recognised
•Insert a FAT16 or FAT32-formatted SD card.
•Disable write-protection.
–
26
Conductivity
measurement
Measured value outside the measuring range.
•Check set value in the customer or service menu.
•Check the sensor and cabling.
–
27
Conductivity
exceeded
•Set value exceeded.
•Cartridge capacity expired.
•Check set value in the Customer or Service menu.
•Replace the cartridge.
"OK"
29
Communication
Master-slave communication or master controller faulty
Check connection.
–
30
I/O module fault
•I/O module defective.
•Connection between option card and controller faulty.
•Option card defective.
•I/O module activated but not present.
•Replace the I/O module.
•Check the connection between option card and
controller.
•Replace the option card.
–
31
EEPROM defective
•EEPROM defective.
•Internal calculation error.
Inform Reflex Customer Service.
–
32
Under voltage
Supply voltage not achieved.
Check voltage supply.
–
33
Adjustment
parameter
EEPROM parameter memory defective.
Inform Reflex Customer Service.
–
34
Main board
communication
faulty
•Connection cable between display and I/O circuit
board defective.
•Main board defective.
Inform Reflex Customer Service.
–
35
Digital limit switch
voltage faulty
Short-circuit of limit switch voltage.
Check the wiring at the digital inputs (water meter, for
example).
–
36
Analogue limit
switch voltage faulty
Short-circuit of limit switch voltage.
Check the wiring at the analogue inputs
(pressure/conductivity).
–
37
Limit switch voltage
MBV1
Short-circuit of limit switch voltage.
Check the wiring at the 2-way motorized ball valve.
–
39
Pressure jumper
Main board jumper does not match configuration.
Check jumper (J1) position.
–
40
Level jumper
Main board jumper does not match configuration.
Check jumper (J1) position.
–
41
Replace battery
Battery discharged.
Replace backup battery in control unit.
–
42
Bus module
Bus module was not detected.
•Check the set values.
•Check the bus module.
–
43
Outside operating
range
Operating range exceeded.
•Lower the system pressure.
•Check ball valves on pump discharge side.
–