Regency Fireplace Products Bellavista B41XTCE User manual

B41XTCE Gas Fireplace
Model B41XTCE-NG10 B41XTCE-LP10
Fuel Type Natural Gas Propane
Minimum Supply Pressure 5” W.C./C.E. (1.25 kPa) 11” W.C./C.E. (2.74 kPa)
Manifold Pressure - High 3.5” W.C./C.E. (0.87 kPa) 10” W.C./C.E. (2.49 kPa)
Manifold Pressure - Low 1.6” W.C./C.E. (0.40 kPa) 6.4” W.C./C.E. (1.60 kPa)
Orice Size -Altitude 0-4500 ft. #30 DMS #49 DMS
Minimum Input
Altitude 0-4500 ft. (0-1372m)
30,000 BTU/h
(8.79 kW)
29,500 BTU/h
(8.65 kW)
Maximum Input
Altitude 0-4500 ft. (0-1372m)
42,500 BTU/h
(12.45 kW)
37,500 BTU/h
(10.99 kW)
Q
P
U
V
T
Openingfor gas
connection
11"(279mm)
dia. Hole through
wall Vent.
Non-Combustible
Header
(steel stud) on edge
Drywall
(orother
facing)
W
Non-CombustibleFacing
S
S
R
Non-combustible
Header
(steel stud
on edge)
M
N
L
O
** Important: Framing height requires consideration of the hearth depth.
Dimension N = N + the thickness of the installed hearth.
Approved Venting Systems
Flex Vent Systems: FPI AstroCap™ Flex Vent
Rigid Pipe Vent Systems: Simpson Direct Vent Pro®
Selkirk Direct-Temp™
Metal-Fab® Sure Seal
ICC Excel Direct Vent
Framing
Dimensions
Description B41XTCE
M Framing Width 47-1/4"(1200mm)
N Framing Height 49-1/2" (1257mm)
O (Rear Vent) Framing Depth - Rear Vent 26-1/2" (673mm)
O (Top Vent) Framing Depth - Top Vent 25-7/8" (657mm)
P Corner Facing Wall Width 65-1/4" (1657mm)
Q Corner Facing Wall Width 91-11/16" (2329mm)
R (Rear Vent) Framed Chase Ceiling - Rear 49-1/2" (1257mm)
R (Top Vent) Framed Chase Ceiling - Top 54-1/2" (1384mm)
S (Rear Vent) Vent Centerline Height - Rear 28-1/2" (724mm)
S (Top Vent) Vent Centerline Height - Top 47-1/2" (1207mm) Rigid / Flex
TGas Connection Height 1-1/2" (38mm)
UGas Connection Inset 5" (127mm)
VGas Connection Width 3-1/4" (82mm)
WNon-Combustible Top Height 13-1/2" (343mm)

B41XTCE Gas Fireplace
Caution Requirements
The top, back and sides of the fireplace are defined by
standoffs. The metal ends of the standoff may NOT
be recessed into combustible construction.
WARNING
Fire hazard is an extreme risk
if these clearances (air space) to combustible materials are not
adhered to. It is of greatest importance that this replace and vent
system be installed only in accordance with these instructions.
CLEARANCES
The clearances listed below are Minimum distances unless otherwise stated:
A major cause of chimney related res is failure to maintain required clearances (air space) to combustible materials. It is of the greatest
importance that this replace and vent system be installed only in accordance with these instructions.
Clearance: Dimension Measured From:
A: Mantel Height (min.) 17-9/16" (446mm) Top of Fireplace Opening
B: Sidewall 9" (229mm) Side of Fireplace Opening
C: Ceiling 36-5/8" (930mm) Top of Fireplace Opening
D: Mantel Depth (max.) 12" (304mm) 25-13/16" (651mm)
from Top of Fireplace Opening
E: Alcove Width 60" (1524mm) Wall to Wall (Minimum)
F: Alcove Depth 36" (914mm) Front to Back Wall (Maximum)
Notes: 0" No Hearth Required
B41 XTCE Clearance Requirements
C
D
A
E
F
C
Close to Ceiling
F
E
Alcove
E
FHorizontal Top 3" (76mm)
Horizontal Side 2 " (51mm)
Horizontal Bottom 2" (51mm)
Vertical Vent 2" (51mm)
Minimum Vent Clearances
to Combustibles

B41XTCE Gas Fireplace
MANTEL CLEARANCES
Note: Ensure the paint that is used on the mantel
and the facing is "heat resistant" or the
paint may discolour.
MANTEL LEG CLEARANCES
Due to the extreme heat this replace emits, the
mantel clearances are critical. Combustible mantel
clearances from top of front facing are shown in the
diagram on the right.
Note: A non-combustible mantel may be
installed at a lower height if the framing
is made of metal studs covered with a
non-combustible board.
Combustible
Mantel Clearances
2
0
12 64
810
0
Top of
Fireplace
Opening
12
1"
7
A
BC
Non-combustible
Header
(steel stud)
on edge
14
To Floor
12
24
Inches
D
6 Non-combustible
Standoff
Mantel Clearances
B41XTCE
A B C D
From Top of
Fireplace Opening
32-11/16"
(830mm)
25-13/16"
(656mm)
22-1/16"
(560mm)
17-9/16"
(446mm)
9 Side Wall
(Measured from side of
Fireplace Opening)
7
4
Mantel leg
Mantel leg
Allowable mantel leg
projection.
3"
1-1/2"

FRAMING & FINISHING
B41XTCE Gas Fireplace
1. Frame in the enclosure for the unit with framing material.
Note: When constructing the framed opening, please ensure there is access to install the gas lines when the unit is installed.
2. For exterior walls, insulate the enclosure to the same degree as the rest of the house; apply vapour barrier and drywall, as per local installation codes.
(Do not insulate the replace itself.)
WARNING: Failure to insulate and add vapor barriers to the inside of the exterior wall will result in operational and performance problems
including, but not limited to: excessive condensation on glass doors, poor ame package, carbon, blue ames etc. These are not product
related issues.
3. The unit does not have to be completely enclosed in a chase. You must maintain clearances from the vent to combustible materials: See "Clearances"
section. Combustible materials can be laid against the side and back standoffs and the stove base.
4. Tile Finish Option 1: Drywall may be installed onto the unit as shown below to create a surface to apply finishing materials such as tile, slate, etc.
Drywall cannot extend beyond the metal surface of the unit.
5. Tile Finish Option 2: If applying a non-combustible finishing material (tile,slate,etc) the material can be installed directly onto the metal surface (clean
front) of the unit in the area shown below.
CLEAN FINISH
6. If applying a non-combustible facing it may be installed over the metal surface (clean front) of the unit in the area shown below.
Combustible and Non-combustible Facing and
Finishing Materials around unit.
38-7/16"
976mm
29"
[737mm]
Combustible
Material
Non-combustible
Finishing Materia
l(ie. tile)
Non-combustible Material (6" x 46-11/16")
Finishing Material
(ie. tile)
Nailing Strip -1/2" back from unit face
Combustible
Material
Non-combustible Supplied with Unit
1-1/2
(38mm)
Ensure finished
material is
brought to lip
1/2" DRYWALL
NON-COMBUSTIBLE FACING
FOR CLEAN LOOK (ie. painted finish)
(SUPPLIED BY OTHERS)
46-11/16"
[1186mm]
1/2" DRYWALL
DO NOT EXTEND
DRYWALL ONTO METAL
SURFACE OF UNIT.
WOOD STUD
44-1/4"
[1124mm]
6"
[152mm] NON COMBUSTIBLE BOARD SUPPLIED W/UNIT
Combustible
Material
Non-combustible
Finishing Material
Non-combustible Material (6" x 46-11/16")
Finishing Material Nailing Strip-flush with unit face
Combustible
Material
Non-combustible Supplied with Unit
1-1/2
(38mm)
Ensure finished
material is
brought to lip
NOTE: The 6" x 46-11/16" non combustible material supplied with this unit can be replaced if trying to achieve a clean finish. A large piece of non
combustible material (ie. 4' x 8' x 1/2" can be used to eliminate taped seams on or near unit.
TILE FINISH

B41XTCE Gas Fireplace
32-7/8"
835mm
25-5/8"
[651mm]
NO FACING OR
FINISHING MATERIAL
IN THIS AREA
No Combustible
Materials in this Area
41-5/8"
[1057mm]
40-5/8"
[1031mm]
4-1/8"
[105mm]
8-3/8"
[213mm]
3-7/8"
[98mm]
3-1/2"
[89mm]
Non combustible - supplied w/unit
J Style trim or metal
corner bead may be
used to finish edges
No Combustible
Materials in this Area
29"
[737mm]
38-7/16"
976mm
7. Non-combustible material (ie. tile, slate, etc) may be brought up to the edge of the glass door of the unit. Minimum clearances must be adhered to, this
will assure ease of glass door removal and access to the lower panel.
NOTE: Non-combustible finishing materials may be of any thickness desired.
Minimum Clearances for Finishing Materials Trim materials
Note: All non-combustible facing material should butt up cleanly
to the flanges around the firebox opening.
Rough edges may be visible from an angle.
To maintain a clean finished edge - facing material edges
may be finished with a J-style trim or metal cornerbead (both
materials available at your local building or hardware store).
IMPORTANT: Materials used must be NON-COMBUSTIBLE.
IMPORTANT FINISHING DETAIL NOTE:
Before placing unit into nal position - it is important to know the total
thickness / height of nished hearth (tile, carpet, etc.) The base of the
replace, 4 sided faceplate or mantel should be level or higher than the
nished hearth height.

B41XTCE Gas Fireplace
The diagrams show all allowable combinations of vent runs with 5" x 8" venting using the Regency direct vent system or rigid vent system.
A vent guard should be used whenever the termination is lower than the specied minimum or as per local codes.
For horizontal terminations the Regency Direct Vent Flex System may be used for installations upto a maximum continuous vent length of 10ft (3.0m).
Note: Must use optional rigid pipe adaptor (Part # 770-994) when using Rigid Pipe vent systems.
• Maintain clearance to combustibles.
• Horizontal vent must be supported every 3 feet.
• Firestops are required at each oor level and whenever passing through a wall.
2
0
12
6
4
8
10
2
0 6
48
Vertical Height (Feet)
Rigid or Flex
47-1/2"
(1.2m)
Horizontal (Feet)
Max. 36(0.9m)
2
0
6
4
8
2
0 6
48
Vertical Height (Feet)
28 -
1/2"(0.7m)
Horizontal (Feet)
Max. 36"(0.9m)
Vent Restrictor - Set 1 Factory Setting - No Restrictor Required
VENTING ARRANGEMENTS FOR HORIZONTAL TERMINATIONS
FLEX VENT OR RIGID PIPE 5" X 8"
REAR VENTING DEFLECTOR INSTALLATION
FOR REAR VENTED HORIZONTAL TERMINATIONS
Rear Venting Deector
The Rear Vent Deector comes with the unit. When the unit is shipped
the deector is slightly tucked underneath the top nailing strips located
at the top of the rebox.
NOTE: The Rear Venting Deector must be installed before the unit is
put in place.
IMPORTANT
Must use Rear Venting Deector packaged with unit in
rear vent horizontal termination applications.
Rear Venting
Deflector
1) Secure the rear venting
deector to the wall thimble
using 2 screws as shown.
Ensure to use the same screw
holes as the wall thimble.

B41XTCE Gas Fireplace
16
2
2
0
0
12
12
6
6
18
4
47-1/2"
(1207mm)
Minimum
Height
Requirement
4
14
8
8
10
10 14 16 18 20
Vertical Height (Feet)
Horizontal (Feet)
Restrictor 1-1/2 Open
Set 3
Restrictor 2-1/2 Open
Set 2
Restrictor 3-1/2 Open
Set 1
VENTING ARRANGEMENTS
FOR HORIZONTAL TERMINATIONS
The diagram shows all allowable combinations of vertical runs with horizontal
terminations, using one 90o(two 45o elbows equal one 90oelbow).
• Maintain clearances to combustibles as listed in "Clearances" section
• Horizontal vent must be supported every 3 feet.
• Firestops are required at each oor level and whenever passing through
a wall.
• A wall thimble is mandatory for all horizontal terminations due to high
temperatures.
VENTING ARRANGEMENTS
FOR VERTICAL TERMINATIONS
The shaded area in the diagram shows all allowable combinations of straight
vertical and o󰀨set to vertical terminations, using two 90oelbows, with Rigid
Pipe Venting Systems for Propane and Natural Gas. Two 45o elbows
equal to one 90oelbow. Maximum of four 45oelbows allowed.
Minimum
8 (2.4m)
Min. 47-1/2
(1.2m)
0
2
4
6
40
8
10
12
14
16
18
20
22
24
26
28
30
Vertical Height (Feet)
32
34
36
38
68
Horizontal (Feet)
2
0
4 10 12
Restrictor 1-1/2 Open
Maximum 10 Centerline to Centerline
Restrictor 2-1/2 Open
Maximum 8 Centerline to Centerline
Restrictor 3-1/2 Open
Set 2
Set 3
Set 1
• Vent must be supported at o󰀨sets.
• Firestops are required at each oor level and whenever
passing through a wall.
• Maintain clearances to combustibles as listed in the
"Clearances" section.
• Refer to the "Vent Restrictor Position" section for
details on how to change the vent restrictor from the
factory setting to 2-1/4" opening ,1-5/8"opening and
to 1-1/16" opening.
Note: Must use optional ue adapter when using Rigid
Pipe (Part # 770-994..