Reiner P1-MP2-RD User manual

GB
P1-MP2-RD
Operating Manual

7
1
Weld seam
2
Zip fastening
3
Clip
4
Print head
5
Clip arms
6
Print head nozzles
7
Print head contacts
AD
B
C
E
1
2
3
4
5
6
7
3
3
4
5
7

8
GB
For your safety
DANGER Warnings about risks where non-observance
of the measures may directly cause death or
serious injury.
WARNING Warnings about risks where non-observance
of the measures may cause death or serious
injury.
CAUTION Warnings about risks where non-observance of
the measures may cause injury.
PLEASE NOTE Warnings about risks where non-observance of
the measures may cause material damage.
Instructions and tips
Safety instructions for MP ink
WARNING
Special ink is highly flammable. Risk of burns!
„Store at 10 °C - 20 °C.
„Do not expose to direct sunlight.
WARNING
If in eyes.
„Rinse cautiously with water for several minutes.
„Remove contact lenses, if present and easy to do.
„Continue rinsing. Immediately call a POISON CENTER
or doctor/physician.

9
1. Making the print head ready for use
1.1. Opening the pack _Fig. A
The aluminium pouch has a resealable zip fastening
2
.
„With scissors, cut open the top of the pack between
the weld seam
1
and the zip fastening
2
.
„Unzip
2
the pack.
„Take out the print head
4
.
1.2. Releasing the clip _Fig. B+ C
The print head
4
is supplied with a reusable clip
3
.
„Place the print head
4
on a firm surface at an angle
of about 45° as shown in figure C.
„Hold the red clip
3
by the point with one hand.
„With the other hand, press the print head
4
down firmly. The
clip arms
5
will spring out and the print head
4
will slide
away from the clip
3
.
2. Printing material
For the best results, use material that is clean, non-greasy, dry
and at the same temperature as the print head.
Before carrying out a large print job, perform a test print.

10
GB
3. Storage _Fig. A+ D
MP ink is fast-drying. The time it takes the print head
nozzles
6
to dry up depends on the ambient temperature
and the humidity.
- If the printing break will probably take more than 5 minutes,
the print head
4
should be protected with the clip
3
.
- If the printing break will probably take more than 2 hours,
the print head
4
with the clip
3
should be stored in the
air-tight aluminium pouch.
„Remove the print head
4
out of the device.
„Place the print head
4
with the clip
3
on a smooth and solid
surface as shown in figure D.
„Press the print head
4
down until it snaps in the clip
3
.
„Place the print head
4
into the aluminium pouch and close
the zip fastening completely.
Use the print head within four weeks after opening.

11
4. Environmental Conditions
Temperature for storage 10°C to +20°C
Temperature for transport -20 °C to +40 °C (up to 24 hours)
5. Troubleshooting
Dried ink on the print head nozzles
6
may result in streaks
or reduced print quality.
5.1. Automatic cleaning
„Read the information about the cleaning of the print head
nozzles
6
in the manual for the electronic stamp.
5.2. Cleaning the print head nozzles manually
If the automatic cleaning of the nozzles
6
does not produce the
desired result, we recommend proceeding as follows:
„To remove dried ink, press a soft cloth, if necessary lightly
soaked in ethanol (spirits), against the print head nozzles
6
for about 3 seconds.
„Dab off the dissolved ink and wipe the nozzles dry.

12
GB
5.3. Reactivating the print head
If ink has dried inside the print head
4
it may be necessary
to reactivate it.
„Lay the print head down on a firm surface protected by
a lint-free cloth or piece of material.
„Place the syringe supplied firmly against the opening on top
of the print head
4
and carefully inject a small amount of air
(approx. 0.5 ml).
PLEASE NOTE
Risk of staining from discharged ink.
„Wipe up discharged ink with a lint-free cloth or piece of
material.
5.4. Cleaning the print head contacts
In rare cases, dirt on the print head contacts
7
may result in
inferior printing results.
„Clean the contacts on the print head
4
and in the device with
a soft cloth or cotton bud, if necessary lightly soaked
in ethanol (spirits).
Disposal
Directive 2002/96/EC (WEEE)
Electrical and electronic equipment and batteries
should not be disposed of along with domestic
or general waste. Dispose of equipment in an
environmentally friendly way.

37
Notes

Ernst Reiner GmbH & Co. KG
Baumannstr. 16
78120 Furtwangen
Phone [phone]
Fax [phone]
[e-mail]
www.reiner.de
Award for
Operational
Excellence
|ZN-791061-001 F|02-2014
Danger
REINER MP2 RD
4 ml
Flammable liquid and vapour.
Causes serious eye damage.
H318H226
Acid Red 52Ethanol