REITEL DUSTY MINI User manual

Operating Instructions
LABORATORY EQUIPMENT
REITEL Feinwerktechnik GmbH
Senfdamm 20 | 49152 Bad Essen
Phone: [phone] | Fax: [phone]
www.reitel.com | [email protected]
DUSTY MINI

II
Dear Customer!
The suction levels of the DUSTY-series are perfectly suited for the removal of dust and
contaminants at the workbench or production units in the laboratory. The DUSTY MINI with
filter bag and fleece filter basket is a dry vacuum cleaner with excellent suction power and
extremely quiet 62 dB(A) noise emission.
Any other use or use beyond this is deemed improper. For resulting damage the
user/operator of this device is solely responsible.
Prior to installation of the device operating instructions and especially the safety instructions
must be read and followed by all personnel who use this device.
After having unpacked the device, please check carefully whether transportation damages of
any kind have occurred. If that is the case, the carrier or manufacturer must be notified within
3 days. The company will not be responsible for any damages found after that.
These operating instructions must be read and followed by all personnel who use this device.
To ensure quick access we recommend to keep it at a safe place near the device. In case of
loss it can be ordered at a nominal fee from the manufacturer.
This document is protected by the copyright law. Passing on or duplication of this document
or extracts thereof, evaluation and communication of its contents are not authorised. In case
of loss it can be ordered from the manufacturer.

III
INDEX
EQUIPMENT................................................................................................................. 4
BASIC EQUIPMENT....................................................................................................... 4
SPECIAL ACCESSORIES................................................................................................ 4
OPERATING ELEMENTS................................................................................................ 5
TECHNICAL DATA......................................................................................................... 6
SAFETY NOTES........................................................................................................... 7
GENERAL SAFETY NOTES ............................................................................................ 7
SPECIFIC SAFETY NOTES............................................................................................. 8
INSTALLATION ............................................................................................................ 9
INSTALLATION.............................................................................................................. 9
HOSE INSTALLATION .................................................................................................... 9
FILTER INSTALLATION .................................................................................................. 9
CONNECTION OF POWER TOOLS ................................................................................... 9
NOTES FOR THE USER..............................................................................................10
HOW TO START THE SUCTION UNIT...............................................................................10
REPLACING FINE DUST FILTER,FILTER BAG AND FLEECE FILTER BASKET.........................10
TROUBLESHOOTING .................................................................................................11
MAINTENANCE...........................................................................................................12
WARRANTY.................................................................................................................13
DISPOSAL REGULATIONS ........................................................................................16
SPARE PARTS LIST ...................................................................................................17
EC CONFORMITY DECLARATION.............................................................................18

4
Equipment
Basic Equipment
•DUSTY MINI single workplace suction
•3,0 m suction hose
•10 m cable
•Fleece filter basket (1 piece)
•Filter bag (1 piece)
•Fine filter fleece (1 piece)
Special Accessories
•Order-No.: 22905000 Filter bag DUSTY MINI (5 pieces/pack)

5
Operating Elements
1 On/off switch
2 Inlet fitting
3 Suction hose
4 Handle with cable receptacle
5 Upper section of the suction unit (light grey)
6 Suction power control switch
7 Retaining clamps
8 Dirt tank (dark grey)
Device view
1
2
3
6
4
8
5
7
Detail 1
Detail 2
Detail 4
Detail 3
Detail 5
Detail 6
Inlet fitting
Upper section of suction
Fleece filter basket
Interior of the unit
Fine dust filter fleece
Upper section of suction

6
Technical Data
Line voltage
230 V/50–60 Hz
Current consumption
1.250 W
Height/width/depth
400/290/405 mm
Weight
5 kg
Dust collection
95 % (class M)
Sound level
62 db(A)
Tank volume
13 l
Housing
plastic
Order-No.:
12900000
Made in Germany (Subject to modifications)

7
Safety Notes
General Safety Notes
•All equipment undergoes final inspection and testing before leaving our factory. However,
if equipment is damaged during shipping or through any other circumstances, it must not
be used in service. Please check the device regularly for damages. Damaged parts
should be replaced immediately.
•All power/air/water/gas sources should be rated for the demands of the device as listed in
the technical data sheets. Maximum ratings must not be exceeded. All VDE (Verein
Deutscher Elektro-Ingenieure) standards should be followed. Equipment should be
grounded according to standards.
•Adherence to valid regulations regarding necessary checks (e.g. according to Accident
Prevention & Insurance or electrical equipment) is exclusively taken over by the
buyer/user of this product.
•This device has been designated to be used only for its intended purpose. All other
applications must be prohibited for safety reasons as otherwise the manufacturer’s
warranty expires.
•The device should be set-up in a clean, well-ventilated room, if necessary under a hood.
•Supporting surfaces should be straight, flat and adequately stable.
•Don’t place anything on top of the machine.
•To avoid injury, appropriate protection should be worn (e.g. gloves, safety glasses, safety
shoes, hearing protection etc.)
•If the machine is defective or working improperly it must be taken out of service. In case
of further use of the machine the owner will be held responsible for any consequential
damage.
•To prevent accidents from water, fire or explosion, all power/air/water/gas sources should
be turned off after working hours and during breaks, and secured against unauthorized
access.
•When carrying out maintenance works or repairs or when opening the device always turn
off the main power switch and unplug the whole unit.
•Repairs should be carried out only by the manufacturer or by qualified and certified
personnel appointed according to chapter 7 –warranty.
•In case of leaking water out of housing or tank shut down device and call service.
•Check all hose joints for tightness, if necessary fasten clamps.

8
Specific Safety Notes
•This device is exclusively designed to pick up dry dust.
•Don’t pick up any explosive, burnable or aggressive fluids or dust with the suction unit.
•This suction is not suitable for picking up harmful dust, risking to damage the filter
element (e.g. glass splinters, metal etc.).
•This machine is not suitable for continuous operation.
•Always turn the machine off and unplug it before carrying out any maintenance work or
cleaning.
•User accessories provided for filling and/or maintenance.
•Don’t perform any other maintenance work than listed in the operating instructions. Any
operation not listed in the operating instructions may bear risks.
•Always insert a filter bag and/or fleece filter basket prior to dry dust pick up.
•Do not damage the mains power lead (e.g. by driving over it, pulling or crushing it).
•Using an extension cable the minimum cross-sections must be in compliance with
requirements (up to 20 m →1,5 mm²; 20 until 50 m →2,5 mm²).

9
Installation
The equipment delivered is ready for immediate use. The sealed plug can be connected
directly to the mains supply 230 V/16 A. For installation please refer to safety notes in
chapter 2.
Installation
1. Ensure that the suction is switched off with the on/off switch (1).
2. Plug the power cable into a properly installed and fused socked with earthing contact.
Hose installation
1. Introduce the hose coupling (3) into the inlet fitting (2) of the suction (see Detail 1).
2. Check tight fit of the suction hose (3).
Filter Installation
1. Open the retaining clamps (7) and remove the upper section of the suction unit (5) (see
Detail 2).
2. Take the fleece filter basket (Detail 3) out of the lower section of the suction unit.
3. Put the filter bag properly on the inlet fitting in the dirt tank (see Detail 4).
4. Reinsert the fleece filter basket (Detail 3).
5. Reinstall upper section of the suction unit (5) and close the retaining clamps (7) (see
Detail 6).
Connection of power tools
Note:
To comply with regulations, only approved dust producing tools may be connected. The
maximum power consumption of the connected electrical appliance is stated in “Technical
data chapter 9. The operating instructions incl. safety instructions for the connected tool
have to be adhered to.
1. Ensure that the suction is switched off with the on/off switch (1).
2. Switch off the power tool.
3. Put the end of the suction hose (3) with the coupling bush to the power tool.

10
Notes for the User
The DUSTY MINI is a silent and powerful dry suction unit. Using both fleece filter basket and
filter bag, high level filtration is achieved for picking up dry substances.
How to start the suction unit
1. Switch off suction with on/off switch (1). The suction’s motor starts. Now switch on power
tool.
2. After work is completed switch off the power tool and then the suction with the on/off
switch (1).
3. Roll up the cable receptacle at the handle (4) for storage.
Replacing fine dust filter, filter bag and fleece filter basket
1. Open the retaining clamps (according to chapter 3.3) and remove the upper section of
the suction unit.
2. Take out the fleece filter basket (see Detail 3).
3. Remove the old filter bag from the inlet fitting and reinsert the new filter bag (see Detail
4). Pay attention to tight fit of the filter bag (dispose of the filter bag in compliance with
legal regulations).
4. Turn around the upper part of the suction unit and remove the fine dust filter fleece (see
Detail 5) in the upper section of the suction unit. Use suction to remove dust from fine
dust filter fleece or if necessary replace it (dispose of the fine dust filter fleece according
to legal regulations).
5. Reinsert the fleece filter basket.
6. Reinsert the upper section of the suction and close the retaining clamps.

11
Troubleshooting
Device cannot be switched on (motor
doesn’t start).
a. Check the fuse of the building.
b. Overload protection is activated (switch
off the suction and allow it to cool for
approx. 5 minutes).
Low suction capacity.
a. Clogged suction hose or nozzle→clean
suction hose / nozzle.
b. Gasket between tank and upper section
of suction unit is dirty → clean gasket.
c. Full filter bag →Replace it.
d. Fleece filter basket or fine filter fleece is
dirty →clean fleece filter basket or fine
filter fleece.

12
Maintenance
•Regularly check the device state. Pay attention to visible damage to housing or power
cord.
•Regularly replace the filter bag (see chapter 4.2 Replacing fine dust filter, filter bag and
fleece filter basket).
•Regularly empty or clean the fleece filter basket (see chapter 4.2 Replacing fine dust
filter, filter bag and fleece filter basket).
•Regularly clean the housing with a damp cloth.

13
Warranty
We, REITEL Feinwerktechnik GmbH, offer a 1 year’s warranty beginning from the proven
date of purchase. This warranty covers all defects traceable to materials, design or
workmanship. The following warranty regulations are applicable:
Within the warranty period Reitel Feinwerktechnik GmbH or an authorized distributor agrees
at its sole option, to perform repair or replace this product at no charge covering all defects
traceable to materials, design or workmanship. Warranty only applies to appropriate use and
regular maintenance of this product according to the operating instructions. Claims under
warranty are restricted to complementary performance. Additional claims, especially claims
for indemnifications, are not covered by this warranty.
1.
Warranty claims have to be addressed to the distributor the product was purchased from or
directly to our service department.
Contact:
REITEL Feinwerktechnik GmbH
Senfdamm 20
49152 Bad Essen
Germany
Phone: [phone] (Service Department)
Phone: [phone] (Reception)
Fax-No: [phone]
2.
In case of warranty claim application the sales receipt or your purchase invoice showing the
date of purchase of the product and the serial number must be furnished. Securely pack and
ship the device, freight charges prepaid, at your own risk to us, along with a report describing
the defect. We reserve the right to decline warranty if this information has been removed or
modified after purchase of the product or if they are not included in case of warranty claims.
3.
Warranty repairs have to performed by REITEL Feinwerktechnik GmbH or by authorised
distributors. Repairs performed by non-authorised companies will void the claim for refund
since damages to the product resulting hereof are not covered by warranty.
4.

14
If the unit sent in for repair or replacement is still under the original warranty then warranty is
to the end of the original 1 year warranty.
5.
If the unit is destined to be operated in another country than originally intended and
manfactured for, modifications to the product might be necessary to comply to special
technical and /or safety standards of that specific country. Such modifications are no defects
traceable to materials, design or workmanship. and are therefore expressly excluded from
warranty claims.
Modification costs or damages arising from operation of the product under deviating
conditions are not covered by warranty.
6.
Exclusions from warranty:
−Service and maintenance work as well as repair and replacement of consumables
according to our consumables‘ list
−Transportation cost of the machine or installation and dismounting expenses incurred
−Damages due to use of the product other than for its intended purpose
−Damages due to faulty installation or insufficient maintenance of the product (e.g.
decalcification)
−Damages due to natural disaster e.g. lightning, water, fire, act of nature beyond
control, war, inadequate line voltage, insufficient ventilation, no decalcification,
insufficient care and cleaning or non-adherence to operation and maintenance
instructions according to the accompanying operation guide.
−Damage due to use of the product other than in accordance with the instructions
provided by REITEL Feinwerktechnik GmH;
−The warranty does not cover the cost of removal and replacement of parts and
accessories, unless supplied as original equipment by REITEL Feinwerktechnik
GmbH
−All kind of damages occurred not directly at the device as well as consequential
damages (e.g. damages to furniture due to a lack of water, downtime of the machine,
material, lost working hours, wages and other consequential damages).
This warranty shall be rendered null and void if:
−the product has been subject to any modification, repair or replacement other than as
authorised by REITEL Feinwerktechnik GmbH
−the product is continued to be operated despite a functional defect

15
7.
The warranty is device specific and may be claimed, within the warranty period, by any
person who has legally acquired the device.
8.
Consumables are excluded from warranty. Spare parts are subject to a warranty coverage of
6 months against all defects traceable to materials, design or workmanship according to
these warranty regulations.
9.
Legal default claims on the part of the purchaser remain unaffected by this warranty.
10.
We reserve the right to charge a fee if repair of the device is rejected and the device is
destined to be sent back unrepaired.
11.
Please note:
Upon repair or replacement of this unit, personal data and settings might get lost or
damaged. We don’t accept liability for all kind of data loss. The customer is advised to
backup essential programs and data before sending for service.
12.
This warranty shall be interpreted in accordance with German law to the exclusion of UN
sales law. Place of jurisdiction is our business location.
13.
If any provisions of this warranty are judged to be illegal or unenforceable, the continuation in
full force and effect of the remaining provisions will not be prejudiced. The provisions of this
warranty judged to be illegal or unenforceable shall be construed so as to give effect to the
intent manifested by the provision held invalid, illegal or unenforceable and to give effect to
section 13 hereof.
14.
Should you need to borrow a device while your device is being repaired, please contact
Messrs. REITEL or your distributor. These loans are a service for which availability cannot
necessarily be guaranteed. After the warranty period, a free may be charged for loan
equipment as well as for shipping and packaging.

16
Disposal Regulations
According to valid laws our devices are properly disposed of according to B2B–
Regulations for proper disposal. Pls. contact your local dealer for additional
information.

17
Spare Parts List
Best.-Nr.:
Ref.:
Menge
Qty.
ME
Unit
E7811500
Absaugschlauch, 3 m
Suction hose, 3 m
1
Stck
piece
E7874200
Ring für Absaugschlauch
Ring for hose adapter
1
Stck
piece
E7874100
Überwurfmuffe
Lock brush
1
Stck
piece
E7294000
Werkzeugadapter
Tool Adapter
1
Stck
piece

18
EC Conformity Declaration

19

We manufacture in compliance with Quality Management ISO 9001:2015, incorporating
established standards.
REITEL Feinwerktechnik GmbH
Senfdamm 20 | 49152 Bad Essen
Tel.: [phone] | Fax: [phone]
www.reitel.com | [email protected]
062019