REITEL ERGORET CLASSIC User manual

Operating Instructions
LABORATORY EQUIPMENT
IN STAINLESS STEEL
ERGORET CLASSIC
REITEL Feinwerktechnik GmbH
Senfdamm 20 | 49152 Bad Essen
Tel.: [phone] | Fax: [phone]
www.reitel.com | [email protected]

II
Dear customer!
The ERGORET CLASSIC workstation keeps the water and dirt in a closed system while
working with zirconia or other materials. The hood made of stainless steel and safety glass is
used in the processing of gypsum, plastic, metal alloys and prevents flying grinding chips
around. Gases and harmful odors remain in the interior, or are transported away from there
by means of an extraction unit. A bright work light illuminates the area well for you.
Any other use or usage beyond this scope is considered unintended use. The manufacturer
shall not be responsible for any damages that may result thereby. Prior to installation of the
device operating instructions and especially the safety instructions must be read and
followed by all personnel who use this device.
After having unpacked the device, please check carefully whether transportation damages of
any kind have occurred. If that is the case, the carrier or manufacturer must be notified within
3 days. The company will not be responsible for any damages found after that.
These operating instructions must be read and followed by all personnel who use this device.
To ensure quick access we recommend to keep it at a safe place near the device. In case of
loss it can be ordered from the manufacturer.

III
INDEX
TECHNICAL DESCRIPTION......................................................................................... 4
BASIC EQUIPMENT ....................................................................................................... 4
DEVICE COMPONENTS.................................................................................................. 5
TECHNICAL DATA......................................................................................................... 7
SAFETY NOTES........................................................................................................... 7
GENERAL SAFETY NOTES ............................................................................................ 7
SPECIFIC SAFETY NOTES............................................................................................. 8
INSTALLATION............................................................................................................ 8
INSTALLATION.............................................................................................................. 8
CHANGING COLLAR OF HAND-THROUGHPUT................................................................... 9
OPERATION................................................................................................................. 9
TROUBLESHOOTING .................................................................................................. 9
MAINTENANCE............................................................................................................ 9
WARRANTY.................................................................................................................10
DISPOSAL REGULATIONS ........................................................................................13
SPARE PARTS LIST ...................................................................................................13
EC CONFORMITY DECLARATION.............................................................................14

4
Technical description
Basic equipment
•Workstation ERGORET CLASSIC incl. lighting
•Adapter for suction hose
•External power supply

5
Device components
1 Lid opener
2 Glass lid (safety glass)
3 Hand-throughput (collar with trim ring)
4 Opening for handpiece (collar with trim ring)
5 Fixing screws of the openings
6 Trim ring
7 Main switch
8 Connection for external power supply
9 Power supply
10 LED lamp (inside the housing)
11 Suction tube
Fig.: Side view
Fig.: LED lamp
1
3
4
5
9
6
10
7
2

6
Fig.: Rear view
8
11
9

7
Technical data
Line voltage
230 V/50–60 Hz
Current consumption
26 W
Height / Width / Depth
260+240/460/430 mm
Weight
8 kg
Sound level
≤70 dB(A)
Housing
Stainless steel
Order-No.:
16901001
Made in Germany (Subject to modifications)
Safety Notes
General Safety Notes
•All equipment undergoes final inspection and testing before leaving our factory. However,
if equipment is damaged during shipping or through any other circumstances, it must not
be used in service. Please check the device regularly for damages. Damaged parts
should be replaced immediately.
•All power / air / water / gas sources should be rated for the demands of the device as
listed in the technical data sheets. Maximum ratings must not be exceeded. All VDE
(Verein Deutscher Elektro-Ingenieure) standards should be followed. Equipment should
be grounded according to standards.
•Adherence to valid regulations regarding necessary checks (e.g. according to Accident
Prevention & Insurance or electrical equipment) is exclusively taken over by the
buyer/user of this product.
•This device has been designated to be used only for its intended purpose. All other
applications must be prohibited for safety reasons as otherwise the manufacturer’s
warranty expires.
•The device may only be used by persons who have been instructed in the handling and
are expressly commissioned with the operation.
•The device should be set-up in a clean, well-ventilated room, if necessary under a hood.
•Supporting surfaces should be straight, flat and adequately stable.
•No objects may be placed on the device.
•To avoid injury, appropriate protection should be worn (as gloves, safety glasses, safety
shoes, hearing protection etc.)

8
•If the machine is defective or working improperly it must be taken out of service. In case
of further use of the machine the owner will be held responsible for any consequential
damage.
•To prevent accidents from water, fire or explosion, all power/air/water/gas sources should
be turned off after working hours and during breaks, and secured against unauthorized
access.
•When carrying out maintenance works or repairs or when opening the device always turn
off the main power switch and unplug the whole unit.
•Repairs should be carried out only by the manufacturer or by qualified and certified
personnel appointed according to chapter 7 –warranty.
•In case of leaking water out of housing or tank shut down device and call service.
•Check all hose connections for leak tightness, if necessary tighten hose clamps again
Specific Safety Notes
•The workstation is sensitive to alcohol, chemicals, concentrated mineral acids, aromatic
hydrocarbons and chlorinated hydrocarbons, esters, ethers and ketones!
•The device may only be cleaned with solvent-free cleaners.
Installation
The electrical equipment is ready for immediate use. The sealed plug can be connected
directly to the mains supply 230 V/16 A. For installation please refer to safety notes in
chapter 2.
Installation
1. Establish the power supply with the plug-in power supply. The jack plug is inserted into
the junction box (below) on the back of the device.
2. Plug the supplied adapter onto the suction tube (11),
3. Connect an extraction unit or a water drain when the unit is used under wet conditions
(both not included).

9
Changing collar of hand-throughput
1. Order a new hand-throughput collar from your dealer (see spare parts list).
2. Remove the screws (5) on the corresponding trim ring (6).
3. Remove the trim rings and replace the old collar.
4. 4. Close the rings with the screws. Make sure the collar is seated properly.
Operation
1. Switch on the lighting with the main switch (7).
2. Use the inlet of the hand-throughput (3) and the opening for the handpiece (4).
3. Switch off the lighting after completing the machining process.
Troubleshooting
Lighting does not work.
a. Check main fuse.
b. Check the device fuse. (The fuse holder
is located at the power connector of the
device.)
c. Power supply plugged in?
d. Replace light
Suction power too low.
Check the extraction unit for blockages.
Maintenance
•When used under wet conditions, clean the device regularly with a damp cloth to prevent
bacterial contamination and bad odors. (see chapter 2.2)
Note
Clean and protect your device at regular intervals with the REITEL stainless steel care
spray (order -no.: 90405000) to remove lime, plaster and dust as well as other
contaminants from the surface of the equipment and to prevent corrosion. The spray
creates a lasting, water repellent protective film which helps keep the equipment clean.

10
Warranty
We, REITEL Feinwerktechnik GmbH, offer a 1 year’s warranty beginning from the proven
date of purchase. This warranty covers all defects traceable to materials, design or
workmanship. The following warranty regulations are applicable:
Within the warranty period Reitel Feinwerktechnik GmbH or an authorized distributor agrees
at its sole option, to perform repair or replace this product at no charge covering all defects
traceable to materials, design or workmanship. Warranty only applies to appropriate use and
regular maintenance of this product according to the operating instructions. Claims under
warranty are restricted to complementary performance. Additional claims, especially claims
for indemnifications, are not covered by this warranty.
1.
Warranty claims have to be addressed to the distributor the product was purchased from or
directly to our service department.
Contact:
REITEL Feinwerktechnik GmbH
Senfdamm 20
49152 Bad Essen
Germany
Phone: [phone] (Service Department)
Phone: [phone] (Reception)
Fax-No: [phone]
2.
In case of warranty claim application the sales receipt or your purchase invoice showing the
date of purchase of the product and the serial number must be furnished. Securely pack and
ship the device, freight charges prepaid, at your own risk to us, along with a report describing
the defect. We reserve the right to decline warranty if this information has been removed or
modified after purchase of the product or if they are not included in case of warranty claims.
3.
Warranty repairs have to performed by REITEL Feinwerktechnik GmbH or by authorised
distributors. Repairs performed by non-authorised companies will void the claim for refund
since damages to the product resulting hereof are not covered by warranty.
4.

11
If the unit sent in for repair or replacement is still under the original warranty then warranty is
to the end of the original 1 year warranty.
5.
If the unit is destined to be operated in another country than originally intended and
manufactured for, modifications to the product might be necessary to comply to special
technical and /or safety standards of that specific country. Such modifications are no defects
traceable to materials, design or workmanship. and are therefore expressly excluded from
warranty claims.
Modification costs or damages arising from operation of the product under deviating
conditions are not covered by warranty.
6.
Exclusions from warranty:
Service and maintenance work as well as repair and replacement of consumables according
to our consumables‘ list
Transportation cost of the machine or installation and dismounting expenses incurred
Damages due to use of the product other than for its intended purpose
Damages due to faulty installation or insufficient maintenance of the product (e.g.
decalcification)
Damages due to natural disaster e.g. lightning, water, fire, act of nature beyond control, war,
inadequate line voltage, insufficient ventilation, no decalcification, insufficient care and
cleaning or non-adherence to operation and maintenance instructions according to the
accompanying operation guide.
Damage due to use of the product other than in accordance with the instructions provided by
REITEL Feinwerktechnik GmH;
The warranty does not cover the cost of removal and replacement of parts and accessories,
unless supplied as original equipment by REITEL Feinwerktechnik GmbH
All kind of damages occurred not directly at the device as well as consequential damages
(e.g. damages to furniture due to a lack of water, downtime of the machine, material, lost
working hours, wages and other consequential damages).
This warranty shall be rendered null and void if:
the product has been subject to any modification, repair or replacement other than as
authorised by REITEL Feinwerktechnik GmbH

12
the product is continued to be operated despite a functional defect
7.
The warranty is device specific and may be claimed, within the warranty period, by any
person who has legally acquired the device.
8.
Consumables are excluded from warranty. Spare parts are subject to a warranty coverage of
6 months against all defects traceable to materials, design or workmanship according to
these warranty regulations.
9.
Legal default claims on the part of the purchaser remain unaffected by this warranty.
10.
We reserve the right to charge a fee if repair of the device is rejected and the device is
destined to be sent back unrepaired.
11.
Please note:
Upon repair or replacement of this unit, personal data and settings might get lost or
damaged. We don’t accept liability for all kind of data loss. The customer is advised to
backup essential programs and data before sending for service.
12.
This warranty shall be interpreted in accordance with German law to the exclusion of UN
sales law. Place of jurisdiction is our business location.
13.
If any provisions of this warranty are judged to be illegal or unenforceable, the continuation in
full force and effect of the remaining provisions will not be prejudiced. The provisions of this
warranty judged to be illegal or unenforceable shall be construed so as to give effect to the
intent manifested by the provision held invalid, illegal or unenforceable and to give effect to
section 13 hereof.
14.
Should you need to borrow a device while your device is being repaired, please contact
Messrs. REITEL or your distributor. These loans are a service for which availability cannot
necessarily be guaranteed. After the warranty period, a fee may be charged for loan
equipment as well as for shipping and packaging.

13
Disposal Regulations
According to valid regulations our devices are properly disposed of according
to B2B –Regulations for proper disposal. Please contact your local dealer for
further information.
Spare parts list
Best.-Nr.
Reference
Stck/ME
Qty.
ME
Unit
E7219200
Dichtung Handdurchführung (Set)
Sealing for hand insert
2
Stck
piece
E7210000
Dichtung Handstück
Sealing for handpiece motor
1
Stck
piece
E7336220
LED Lampe, mit Clips, ohne Trafo
LED lamp, incl. Clips and end caps
1
Stck
piece
E7019910
Schalter EIN/AUS
ON/OFF switch
1
Stck
piece
E7214200
U-Profil Dichtung
U-profile seal
1
m

14
EC Conformity Declaration

15

We manufacture in compliance with Quality Management ISO 9001:2015 incorporating
established standards.
REITEL Feinwerktechnik GmbH
Senfdamm 20 | 49152 Bad Essen
Tel.: [phone] | Fax: [phone]
www.reitel.com | [email protected]
012021