REITEL SANDUBLAST 3 User manual

Operating Instructions
LABORATORY EQUIPMENT
IN STAINLESS STEEL
SANDUBLAST 2 / 3
REITEL Feinwerktechnik GmbH
Senfdamm 20 | 49152 Bad Essen
Phone: [phone] | Fax: [phone]
www.reitel.com | [email protected]

II
Dear Customer!
The devices of the SANDUBLAST series are available either as recycling sandblasting
device SANDUBLAST or as combined units SANDUBLAST 2 or 3 (cover image shows
SANDUBLAST 3). The SANDUBLAST is a manual sandblaster. SANDUBLAST 2 or 3 are
combining a recycling sandblasting device for blasting model castings with a Microfine jet
blaster with two or three chambers. All the advantages of microblasting and recycling
sandblasting technology are combined in one unit, suitable for the following applications:
cleaning, buffing and polishing as well as removing oxide layers and special surface finishing
with sandblasting beads. The special blasting principle and the heated chambers offer a
constant flow of the abrasive that result in a smooth surface being created. Of course, the
maintenance-free quick stop valve is integrated in the blasting unit as well, to provide precise
and economic use of abrasives. Heated chambers prevent abrasive agglomeration leading to
blocked nozzles. Different kind of abrasive graining and adjustable amounts per tank enable
various surface qualities. All commercial abrasives from 25 to 250 my are applicable.
Prior to installation of the device operating instructions and especially the safety instructions
must be read and followed by all personnel who use this device.
After having unpacked the device, please check carefully whether transportation damages of
any kind have occurred. If that is the case, the carrier or manufacturer must be notified within
3 days. The company will not be responsible for any damages found after that.
These operating instructions must be read and followed by all personnel who use this device.
To ensure quick access we recommend to keep it at a safe place near the device. In case of
loss it can be ordered at a nominal fee from the manufacturer.

III
CONTENTS
EQUIPMENT................................................................................................................. 4
BASIC EQUIPMENT....................................................................................................... 4
SPECIAL ACCESSORIES................................................................................................ 4
DEVICE COMPENENTS ................................................................................................. 5
TECHNICAL DATA......................................................................................................... 8
CHAMBERS AND NOZZLES ............................................................................................ 9
SAFETY NOTES..........................................................................................................10
GENERAL SAFETY NOTES ...........................................................................................10
SPECIFIC SAFETY NOTES............................................................................................11
INSTALLATION ...........................................................................................................12
RECYCLING SANDBLASTER INSTALLATION ....................................................................12
RECYCLING SANDBLASTER AND MICROFINE JET BLASTER INSTALLATION ........................12
OPERATION................................................................................................................13
TROUBLESHOOTING .................................................................................................14
MAINTENANCE...........................................................................................................15
WARRANTY.................................................................................................................16
DISPOSAL REGULATIONS ........................................................................................19
SPARE PARTS LIST ...................................................................................................20
EC CONFORMITY DECLARATION.............................................................................22

4
Equipment
Basic Equipment
•SANDUBLAST 2 and 3 are combining a recycling sandblaster with a Microfine jet blaster
with 2 or 3 chambers (to be specified in the purchase order)
•Set of carbide nozzles (dependent on the number of chambers, see chart on page 5)
•Pair of abrasion resistant gloves, medium size (size 9)
•Filling funnel for abrasive material
•Assembly tool for changing tubes
•Power cord / plug
•Foot switch
Special Accessories
•Order-No.: 12900000 DUSTY MINI
•Order-No.: 17902000 DUSTY COMFORT
•Order-No.: 24604100 Pair of abrasion resistant gloves (size 7, small)
•Order-No.: 24604000 Pair of abrasion resistant gloves (size 9, medium)
•Order-No.: 24604200 Pair of abrasion resistant gloves (size 10, large)
•Various carbide nozzles
(see chart on page 5 –please indicate flow size upon placement of order)

5
Device Compenents
1 Power switch
2 Glass pane with protection film
3 Rubber seal (under glass pane)
4 Suction adapter
5 Fuse (with spare fuse)
6 Socket for power supply
7 Socket for foot switch
8 Socket for extraction unit
9 Compressed air outlet
10 Carrying handle
11 Interior light (LED)
12 Screw for opening the glass pane
13 Leather gauntlets
14 Screw plug for abrasive chamber
15 Seal of the abrasive chamber
16 Plexiglass lid of the abrasive chamber
17 Nozzle head (in the abrasive chamber)
18 Abrasive chamber
19 Sealing plug for abrasive chamber outlet
20 Pressure regulator
21 Valve for residual water evacuation
22 Water separator
23 Sand sieve
24 Blast nozzle
25 Nozzle holder
26 Nozzle
27 Nozzle pen
28 Selector switch for abrasive media
29 Abrasive hose (nozzles)
30 Recycling nozzle
31 Angled screws for continuous angle adjustment of the recycling nozzle
32 Abrasive hose (recycling nozzle)
33 Opening in the base tray
34 Hose coupling recycling sandblaster (bottom side)
35 Funnel
36 Foot switch