REITEL SANDUBLAST User manual

Operating Instructions
LABORATORY EQUIPMENT IN
STAINLESS STEEL
SANDUBLAST
REITEL Feinwerktechnik GmbH
Senfdamm 20 | 49152 Bad Essen
Phone: [phone] | Fax: [phone]
www.reitel.com | [email protected]

II
Dear Customer!
The SANDUBLAST is a high-performance re-circulation sandblasting unit for fast and
economic devestment.The nozzle can be fixed at any angle for continuous blasting.
Extremely bright and shadowfree LED lighting ensures that the object being blasted is
perfectly illuminated. The nozzle can be fixed at any angle for continuous blasting.
Any other use or use beyond this is deemed improper. For resulting damage the
user/operator of this device is solely responsible.
Prior to installation of the device operating instructions and especially the safety instructions
must be read and followed by all personnel who use this device.
After having unpacked the device, please check carefully whether transportation damages of
any kind have occurred. If that is the case, the carrier or manufacturer must be notified within
3 days. The company will not be responsible for any damages found after that.
These operating instructions must be read and followed by all personnel who use this device.
To ensure quick access we recommend to keep it at a safe place near the device. In case of
loss it can be ordered at a nominal fee from the manufacturer.
This document is protected by the copyright law. Passing on or duplication of this document
or extracts thereof, evaluation and communication of its contents are not authorised. In case
of loss it can be ordered at a nominal fee from the manufacturer.

III
INDEX
EQUIPMENT................................................................................................................. 4
BASIC EQUIPMENT....................................................................................................... 4
SPECIAL ACCESSORIES................................................................................................ 4
OPERATING ELEMENTS................................................................................................ 5
TECHNICAL DATA......................................................................................................... 7
SAFETY NOTES........................................................................................................... 8
GENERAL SAFETY NOTES ............................................................................................ 8
SPECIFIC SAFETY NOTES............................................................................................. 9
INSTALLATION ...........................................................................................................10
RECYCLING SANDBLASTER INSTALLATION....................................................................10
OPERATION................................................................................................................11
CHRONOLOGICAL RUN OF OPERATION..........................................................................11
TROUBLESHOOTING .................................................................................................12
MAINTENANCE...........................................................................................................13
WARRANTY.................................................................................................................14
DISPOSAL REGULATIONS ........................................................................................17
SPARE PARTS LIST ...................................................................................................18
EC CONFORMITY DECLARATION.............................................................................19

4
Equipment
Basic Equipment
•SANDUBLAST Recycling sandblaster
•One pair of abrasion resistant gloves, (size 9, medium)
•Tool for hose replacement
Special Accessories
•Order-No.: 12900000 DUSTY MINI
•Order-No.: 17902000 DUSTY COMFORT
•Order-No.: 24604100 one pair of abrasion resistant gloves (size 7, small)
•Order-No.: 24604000 one pair of abrasion resistant gloves (size 9, medium)
•Order-No.: 24604200 one pair of abrasion resistant gloves (size 10, large)

5
Operating Elements
1 Power switch
2 Glass pane
3 Protective film (on the glass pane)
4 Rubber seal (under the glass pane)
5 Suction adapter
6 Fuse
7 Socket for suction (power supply)
8 Compressed air connection
9 Carrying handle
10 Interior light (LED)
11 Screw for glass pane opening
12 Leather gauntlets
13 Foot switch
14 Sand sieve
15 Blasting nozzle
16 Nozzle holder
17 Blasting nozzle
18 Angled screws for continuous nozzle adjustment
19 Abrasive hose
20 Compressed air hose
21 Opening in the base tray
22 Base tray
23 Hose coupling recycling sandblaster
24 Power plug
25 Connection for foot switch

6
Device view
Blasting Chamber
14
15
16
17
18
19
20
Foot switch
2, 3
4
1
5
10
6
7
8
9
11
12
24
25
13

7
Base Tray Hose coupling
Technical Data
Line voltage
230 V/50-60 Hz
Current consumption
100 W
Height/width/depth
360+190/480/440 mm
Weight
13 kg
Air consumption
approx. 80 l/min.
Pressue blaster
max. 6 bar
Sound level
65 dB(A)
Housing
Stainless steel
Order-No.:
14604000
Made in Germany (Subject to modifications)
21
23
22

8
Safety Notes
General Safety Notes
•All equipment undergoes final inspection and testing before leaving our factory. However,
if equipment is damaged during shipping or through any other circumstances, it must not
be used in service. Please check the device regularly for damages. Damaged parts
should be replaced immediately.
•All power/air/water/gas sources should be rated for the demands of the device as listed in
the technical data sheets. Maximum ratings must not be exceeded. All VDE (Verein
Deutscher Elektro-Ingenieure) standards should be followed. Equipment should be
grounded according to standards.
•Adherence to valid regulations regarding necessary checks (e.g. according to Accident
Prevention & Insurance or electrical equipment) is exclusively taken over by the
buyer/user of this product.
•This device has been designated to be used only for its intended purpose. All other
applications must be prohibited for safety reasons as otherwise the manufacturer’s
warranty expires.
•The device should be set-up in a clean, well-ventilated room, if necessary under a hood.
•Supporting surfaces should be straight, flat and adequately stable.
•Don’t place anything on top of the machine.
•To avoid injury, appropriate protection should be worn (e.g. gloves, safety glasses, safety
shoes, hearing protection etc.)
•If the machine is defective or working improperly it must be taken out of service. In case
of further use of the machine the owner will be held responsible for any consequential
damage.
•To prevent accidents from water, fire or explosion, all power/air/water/gas sources should
be turned off after working hours and during breaks, and secured against unauthorized
access.
•When carrying out maintenance works or repairs or when opening the device always turn
off the main power switch and unplug the whole unit.
•Repairs should be carried out only by the manufacturer or by qualified and certified
personnel appointed according to chapter 7 –warranty.
•In case of leaking water out of housing or tank shut down device and call service.
•Check all hose joints for tightness, if necessary fasten clamps.

9
Specific Safety Notes
Note:
It is prohibited to use fluids and gaseous media. Application only according to
manufacturer’s instructions.
•Always keep the glass pane closed during operation. Connect the device to an
appropriate suction.
•To avoid injury wear abrasion resistant gloves, goggles and a mask.
•The device may only be operated with non-hazardous commercially available powdered
abrasives.
•No harmful abrasives, gases or fluids may be used.
•No other gases than compressed air shall be used with the device.
•The blasting jet may only be directed to objects to be cleaned, never at living beings.
•Do not install any dust-sensitive devices near the sandblaster.

10
Installation
The electrical equipment is being delivered fully installed. The sealed plug can be connected
directly to the mains supply 230 V/16 A. For installation please refer to chapter 2.
Recycling Sandblaster Installation
Establish compressed air connection (3,5–6 bar).
Connect the suction as follows:
−Put the suction’s plug in the socket outlet (7),
−Secure suction tube to adapter (5),
−Activate the suction.
Use the angled screws (18) to fix the blasting nozzle (17) at any angle.
Fill the base tray (22) of the recycling sandblaster with a sufficient quantity of abrasive
media.

11
Operation
Chronological run of operation
Turn the unit on with the power switch (1).
The sandblaster requires air compression. Set the pressure to 6 bar. (Never exceed the
max. pressure of 6 bar –danger of bursting hoses).
Blasting is initiated with the foot switch (13).
Use the jet nozzle (15) to remove residual abrasives from objects.
After finishing work turn the unit off with the power switch (1).

12
Troubleshooting
Jet becomes irregular.
a. Abrasive might be dirty →change
abrasive.
b. Insufficient quantity of abrasive in the
tank →refill abrasive.
Clumped abrasive.
Only use dry abrasive.
Very dusty working area.
a. Insufficient suction power →Increase
suction power.
b. Filter bag of the suction is full →if
necessary replace filter bag.
c. If necessary clean suction →e.g.
change motor filter.
LED Lamp (10) doesn’t shine.
a. Unplug power cord, check it and
reinsert it.
b. Lamp defective →check it and if
necessary replace it.
Trouble with footswitch (13).
Check the power cord and connect it
properly.

13
Maintenance
•Please check the device regulary for damage. Pay attention to visible damages to the
housing, cable or pressure hoses.
•Worn sandblast hoses need replacing. They are not covered by warranty but considered
normal wear and tear. Hoses in the interior work area are replaced with standard tools.
Worn hoses inside the device have to be replaced by your distributor or REITEL.
•Remove abrasive material in the interior of the unit and clean it regularly. Disconnect the
hose coupling at the bottom of the recycling sandblaster (23) and let the abrasive run out
through the opening in the base tray (22). Dispose of waste abrasive according to
manufacturer’s instructions.
•Clean or replace the suction’s filter regularly.
•Clean the housing regularly with a damp cloth and polish it with the REITEL stainless
steel spray.

14
Warranty
We, REITEL Feinwerktechnik GmbH, offer a 1 year’s warranty beginning from the proven
date of purchase. This warranty covers all defects traceable to materials, design or
workmanship. The following warranty regulations are applicable:
Within the warranty period Reitel Feinwerktechnik GmbH or an authorized distributor agrees
at its sole option, to perform repair or replace this product at no charge covering all defects
traceable to materials, design or workmanship. Warranty only applies to appropriate use and
regular maintenance of this product according to the operating instructions. Claims under
warranty are restricted to complementary performance. Additional claims, especially claims
for indemnifications, are not covered by this warranty.
1.
Warranty claims have to be addressed to the distributor the product was purchased from or
directly to our service department.
Contact:
REITEL Feinwerktechnik GmbH
Senfdamm 20
49152 Bad Essen
Germany
Phone: [phone] (Service Department)
Phone: [phone] (Reception)
Fax-No: [phone]
2.
In case of warranty claim application the sales receipt or your purchase invoice showing the
date of purchase of the product and the serial number must be furnished. Securely pack and
ship the device, freight charges prepaid, at your own risk to us, along with a report describing
the defect. We reserve the right to decline warranty if this information has been removed or
modified after purchase of the product or if they are not included in case of warranty claims.
3.
Warranty repairs have to performed by REITEL Feinwerktechnik GmbH or by authorised
distributors. Repairs performed by non-authorised companies will void the claim for refund
since damages to the product resulting hereof are not covered by warranty.
4.

15
If the unit sent in for repair or replacement is still under the original warranty then warranty is
to the end of the original 1 year warranty.
5.
If the unit is destined to be operated in another country than originally intended and
manufactured for, modifications to the product might be necessary to comply to special
technical and /or safety standards of that specific country. Such modifications are no defects
traceable to materials, design or workmanship. and are therefore expressly excluded from
warranty claims.
Modification costs or damages arising from operation of the product under deviating
conditions are not covered by warranty.
6.
Exclusions from warranty:
−Service and maintenance work as well as repair and replacement of consumables
according to our consumables‘ list
−Transportation cost of the machine or installation and dismounting expenses incurred
−Damages due to use of the product other than for its intended purpose
−Damages due to faulty installation or insufficient maintenance of the product (e.g.
decalcification)
−Damages due to natural disaster e.g. lightning, water, fire, act of nature beyond
control, war, inadequate line voltage, insufficient ventilation, no decalcification,
insufficient care and cleaning or non-adherence to operation and maintenance
instructions according to the accompanying operation guide.
−Damage due to use of the product other than in accordance with the instructions
provided by REITEL Feinwerktechnik GmH;
−The warranty does not cover the cost of removal and replacement of parts and
accessories, unless supplied as original equipment by REITEL Feinwerktechnik
GmbH
−All kind of damages occurred not directly at the device as well as consequential
damages (e.g. damages to furniture due to a lack of water, downtime of the machine,
material, lost working hours, wages and other consequential damages).
This warranty shall be rendered null and void if:
−the product has been subject to any modification, repair or replacement other than as
authorised by REITEL Feinwerktechnik GmbH
−the product is continued to be operated despite a functional defect

16
7.
The warranty is device specific and may be claimed, within the warranty period, by any
person who has legally acquired the device.
8.
Consumables are excluded from warranty. Spare parts are subject to a warranty coverage of
6 months against all defects traceable to materials, design or workmanship according to
these warranty regulations.
9.
Legal default claims on the part of the purchaser remain unaffected by this warranty.
10.
We reserve the right to charge a fee if repair of the device is rejected and the device is
destined to be sent back unrepaired.
11.
Please note:
Upon repair or replacement of this unit, personal data and settings might get lost or
damaged. We don’t accept liability for all kind of data loss. The customer is advised to
backup essential programs and data before sending for service.
12.
This warranty shall be interpreted in accordance with German law to the exclusion of UN
sales law. Place of jurisdiction is our business location.
13.
If any provisions of this warranty are judged to be illegal or unenforceable, the continuation in
full force and effect of the remaining provisions will not be prejudiced. The provisions of this
warranty judged to be illegal or unenforceable shall be construed so as to give effect to the
intent manifested by the provision held invalid, illegal or unenforceable and to give effect to
section 13 hereof.
14.
Should you need to borrow a device while your device is being repaired, please contact
Messrs. REITEL or your distributor. These loans are a service for which availability cannot
necessarily be guaranteed. After the warranty period, a free may be charged for loan
equipment as well as for shipping and packaging.

17
Disposal Regulations
According to valid laws our devices are disposed of according to B2B-
Regulations for proper disposal. Pls. contact your local dealer for additional
information.

18
Spare Parts List
Best.-Nr.
Reference
SANDUBLAST (46.5)
Ersatzteilliste / Spare parts list 03/2019
Stck.
Qty.
VE
Unit
E7930500
Behälterdeckel farblos
Transparent blast chamber cover
1
Stck
piece
E7992600
Behälterknopf zum Verschließen Deckel
Chamber lid locking knob
1
Stck
piece
E6189400
Fußtaster 1-pol. mit Kabel 1,65 m + Kaltgerätestecker
Foot switch 1-pole
1
Stck
piece
E6230200
Glasscheibe, inkl. Folie und Klebepunkte
Glass panel, with protection foil
1
Stck
piece
E6230600
Handdurchführung, 2 St. incl. Ledereinsatz für Lochd. 130mm
Gauntlets, 2 pcs., made of genuine leather
1
Paar
24604200
Handschuhe für Sandstrahlarbeiten Größe 10
Pair of Gloves for sandblasting units, Size L
1
Paar
24604100
Handschuhe für Sandstrahlarbeiten Größe 7
Pair of Gloves for sandblasting units, Size S
1
Paar
24604000
Handschuhe für Sandstrahlarbeiten Größe 9
Pair of Gloves for sandblasting units, Size M
1
Paar
E6230700
Kunststoff-Schutzfolie, 5 St.
Plastic protection foil, 5 pcs.
1
Pack
E7336210
LED Lampe, mit Clips und Endkappe, ohne Trafo
LED lamp, incl. Clips and end caps, without transformer
1
Stck
piece
20280000
Lupe, mit Saugnapf, D75mm
1
Stck
piece
E6202030
O-Ring 65 x 2,5 mm für Behälter ( aussen )
Sealing 65 x 2,5 mm for chamber ( outside )
1
Stck
piece
E7854500
O-Ring für Kammerdeckel 65x3,55
Sealing for chamber lid
1
Stck
piece
E7336100
Rohr Acryl LED-Schutzrohr mit 1 Endkappe 240mm
LED acrylic lamp protection, incl. 1 end cap 240mm
1
Stck
piece
E7872900
Rohrclips 12 mm - Halter für Messingrohr im Behälter
Tube clips 12 mm - Halter für Strahlgriffel
1
Paar
two pcs
E6064800
Schalter mit Lampe grün 2pol.
Power switch incl. green lamp (2 poles)
1
Stck
piece
E6074310
Schlauch, H-PU-8/6 blau
1
m
m
E7049500
Sicherung 10 Amp.
Fuse 10 Amp.
1
Stck
piece
E6283400
Strahldüse Umlaufstrahl, Trichterdüse mit Trennung an
Madenschraube
1
Stck
piece
E7299000
Umlaufstrahldüse komplett (Mischkammer mit Düsen)
Mixing chamber with nozzles (assy)
1
Stck
piece
E6207810
Ventil 2/2-nw4-24VAC ( für Umlaufstrahl )
1
Stck
piece

19
EC Conformity Declaration

We manufacture in compliance with Quality Management ISO 9001:2015 incorporating
established standards.
REITEL Feinwerktechnik GmbH
Senfdamm 20 | 49152 Bad Essen
Phone: [phone] | Fax: [phone]
www.reitel.com | [email protected]
062019