Renesas R0E510Y47LVB00 User manual

User's Manual
R20UT2886EJ0100 Rev.1.00 Page 1 of 9
Jan 20, 2014
R0E510Y47LVB00
Low voltage OCD Board for RL78/G10 Groups
1. Overview
R0E510Y47LVB00 is a debug board for R5F10Y47ASP, R5F10Y46ASP, R5F10Y44ASP, R5F10Y17ASP, R5F10Y16ASP,
R5F10Y14ASP in RL78/G10 groups, which is enabled to effective debug of hardware and software on low voltage user system.
This product is used with E1 emulator. And a box connector of 2.45mm pitch is needed to connecting user system.
Also refer to E1/E20 Emulator Additional Document for User's Manual (Notes on Connecting RL78), when you use this product.
USB interface cable
User interface cable
Host machine
User system
RE510Y47LVB00
E1 emulator
* Do not mount target device on user system.
If target device is mounted, the signals are shorted between
this product and target device on user system.
Figure 1 System Configuration
2. Specifications
Table 1 shows the functional specifications of this product.
Table 1Specifications of this product
Item
Specification
Target MCU
R5F10Y17ASP, R5F10Y16ASP, R5F10Y14ASP (10pin SSOP)
R5F10Y47ASP, R5F10Y46ASP, R5F10Y44ASP (16pin SSOP)
Support Emulator
E1 emulator (E20 emulator is not supported )
Target I/F
8510-4500 : 10-pin type connecter, Sumitomo 3M Limited
8516-4500 : 16-pin type connecter, Sumitomo 3M Limited
Power supply for this product
Emulator or Target system*1
Operating voltage
2.0V to 5.0V*2
Operating temperature
5 to 35
°C
(No condensation)
Storage temperature
-15 to 60°C (No condensation)
Dimensions
65mm * 70mm (Does not include projection) Refer to figure2.
Weight
22g
Note*1: If the user system power supply is turned on be before starting debugger, this product uses 150mA current
from user system.
Note*2: It is different from target devices. The operation voltage range of this product is 5.0V(max.)
R20UT2886EJ0100
Rev.1.
00
Jan 20, 2014

R0E510Y47LVB00 User's Manual
R20UT2886EJ0100 Rev.1.00 Page 2 of 9
Jan 20, 2014
3. Dimensions of This Product
Figure 2Dimensions of this product (R0E510Y47LVB00)

R0E510Y47LVB00 User's Manual
R20UT2886EJ0100 Rev.1.00 Page 3 of 9
Jan 20, 2014
4. Internal Circuit
P00(6pin)
P01(7pin)
P02(8pin)
P03(9pin)
P04(10pin)
P137(3pin)
P40(1pin)
P125/RESET(2pin)
VDD(5pin)
VSS(4pin)
P00,P01,P02,P03,P04,P137
P40
P125/RESET
VDD
VSS
To the emulator
NC7SZ66P5X
NC7SZ66P5X
NC7SZ66P5X
P1
Short pad
（Default is short)
To the emulator
100KΩ
TVDD TVDD
VDD
Connector for the user
system (CN2)
R5F10Y47ASP
2MΩ
2MΩ2MΩ
2MΩ
10uF0.1uF
P00(9pin),P01(10pin),
P02(11pin),P03(12pin),
P04(13pin),P137(4pin)
P05(14pin),P06(15pin),
P122(5pin),P41(1pin)
P07(16pin),P121(6pin),
P40(2pin)
P125/RESET(3pin)
VDD(8pin)
VSS(7pin)
TVDD
Connector for the user
system (CN3)
2MΩ
2MΩ
P05,P06,P07,P121,P122,P41
NC7SZ66P5X
P1
TVDD
VDD
5V
The selector circuit for
microcontroller power supply
1MΩ
TVDD
5V
The power supply
from the emulator TVDD
5V power supply circuit
Figure 3Internal circuit of this product (R0E510Y47LVB00)

R0E510Y47LVB00 User's Manual
R20UT2886EJ0100 Rev.1.00 Page 4 of 9
Jan 20, 2014
5. Connecting Low voltage OCD board with user system
For connecting Low voltage OCD board with user system, need to mount a connector on user system.
Refer to this chapter and user manual of devices, when you design your system.
5.1 The connector for connecting user system and mounting connector
Figure 4The connector for mounting user system and mounting connector
(Target MCU: R5F10Y17ASP, R5F10Y16ASP, R5F10Y14ASP)
Figure 5The connector for mounting user system and mounting connector
(Target MCU: R5F10Y47ASP, R5F10Y46ASP, R5F10Y44ASP)

R0E510Y47LVB00 User's Manual
R20UT2886EJ0100 Rev.1.00 Page 5 of 9
Jan 20, 2014
5.2 Pin assignments of the connector on the user system
Table 2Pin assignments of the connector (Target MCU: R5F10Y17ASP, R5F10Y16ASP, R5F10Y14ASP)
Pin No. Pin Name Input/Output* Remarks
1 P40 - P40 is connected with target
power supply through 100k ohm.
2 P125/RESET Output -
3 P137 Output -
4 VSS - -
5 VDD - -
6 P00 Input / Output -
7 P01 Input / Output -
8 P02 Input / Output -
9 P03 Input / Output -
10 P04 Input / Output -
Note* As seen from this product (R0E510Y47LVB00）
Table 3Pin assignments of the connector (Target MCU: R5F10Y47ASP, R5F10Y46ASP, R5F10Y44ASP)
Pin No. Pin Name Input/Output* Remarks
1 P41 Input / Output -
2 P40 - P40 is connected with target
power supply through 100k ohm.
3 P125/RESET Output -
4
P137
Output -
5 P122/X2/EXCLK Input -
6 P121/X1 Input -
7
VSS
- -
8 VDD - -
9 P01 Input / Output -
10 P02 Input / Output -
11 P03 Input / Output -
12 P04 Input / Output -
13 P05 Input / Output -
14 P06 Input / Output -
15
P07
Input / Output -
Note* As seen from this product (R0E510Y47LVB00）

R0E510Y47LVB00 User's Manual
R20UT2886EJ0100 Rev.1.00 Page 6 of 9
Jan 20, 2014
6. Use procedure
Use this product (R0E510Y47LVB00) by the following procedure.
Connecting this product with emulator.
Connect CN1 of this product with user interface connector of E1 emulator using 14-pin user interface cable.
↓
Connecting this product with user system
Connect CN2 or CN3* of this product with user system.
(Note* Choose by Target MCU.)
↓
Connecting the emulator with host machine
Connect the emulator with host machine using USB cable.
↓
Starting debugger
Start debugger and download user program.
(When you start debugger, you set a setting for using low voltage OCD board.
About the method of detail setting, refer to user’s manual of debugger)
↓
Turning on the power supply of user system
Turn on the power supply of user system. You can start debug.
↓
Turning off the power supply of user system
After finishing the debug, turn off the power supply of user system while user program stop.
(After turn off the power supply, do not operate anything besides exiting debugger)
↓
Exiting debugger
Exit debugger.
↓
Disconnecting the emulator from host machine
Disconnect USB cable from the emulator and host machine.
↓
Disconnecting this product from user system
Disconnect CN2 or CN3 of this product from user system.
↓
Disconnecting this product from the emulator
Disconnect user interface cable from this product and the emulator.

R0E510Y47LVB00 User's Manual
R20UT2886EJ0100 Rev.1.00 Page 7 of 9
Jan 20, 2014
7. Notes on Usage
Read the following notes before using this product. Incorrect operation will damage this product, the user system and
the user program.
Note on the operation voltage:
•The operation voltage range is different from target devices.
The operation voltage range of this product is 5.0V(max.).
Notes on Connecting the Low voltage OCD board:
•Cables must not be connected or disconnected while the user system power is on.
•Before connecting this product with the user system, check that the pin 1 locations on both sides.
Note on Rewriting the Flash Memory:
•The number of MCU’s flash memory rewriting on this product is limited.
If an erasing error occurs during debugging, replace this product.
Notes on Debugging:
•P40 is not connected microcontroller for debug on this product.
It is not possible to debug of P40 port function in this product.
Note on the Flash Programming Software Products (Renesas Flash Programmer, etc.):
•Do not use the flash programming software products for this product.
Note on the RESET:
•After resetting, It occurs the break of hundreds msec for internal debugger process
Note on the data retention power supply voltage:
•Minimum value of the data retention power supply voltage differs from target devises.
The data retention power supply voltage of this product is 1.8V(typ.) / 2.0V(max.).
Note on the A/D Converter:
•The characteristic of the A/D converter differs from target devices because there are some analog
selectors and other devices between the MCU and the user system.

R0E510Y47LVB00 User's Manual
R20UT2886EJ0100 Rev.1.00 Page 8 of 9
Jan 20, 2014
Appendix Compliance Sheet
CAUTION
This is a Test- and Measurement equipment with possibility to be significantly altered by user through hardware
enhancements/modifications and/or test or application software. Thus, with respect to Council Directive
2004/108/EC (Directive on compliance with the EMC protection requirements), this equipment has no autonomous
function. Consequently this equipment is not marked by the CE-symbol.
EEDT-ST-005-20
CAUTION
This equipment should be handled like a CMOS semiconductor device. The user must take all precautions to avoid
build-up of static electricity while working with this equipment. All test and measurement tool including the
workbench must be grounded. The user/operator must be grounded using the wrist strap. The connectors and/or
device pins should not be touched with bare hands.
EEDT-ST-004-10
For customers in the European Union only
The WEEE (Waste Electrical and Electronic Equipment) regulations put responsibilities on
producers for the collection and recycling or disposal of electrical and electronic waste.
Return of WEEE under these regulations is applicable in the European Union only.
This equipment (including all accessories) is not intended for household use. After use the
equipment cannot be disposed of as household waste, and the WEEE must be treated, recycled
and disposed of in an environmentally sound manner. Renesas Electronics Europe GmbH can
take back end of life equipment, register for this service at http://www.renesas.eu/weee
Device files and sample code download(*1)
For target boards the device files and ready-to-use sample
Application(s) are available for download from the Renesas
TOOLWEB,www.renesas.eu/update.
Please mark “Target-Board/Adapter” as tool type and then
Select your target board from the list of products. *1: Applicable in the European Union Only.

Notice
1. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for
the incorporation of these circuits, software,and information in the design of yourequipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising fromthe
use of these circuits, software, or information.
2. Renesas Electronics has used reasonable care in preparing the information included in this document, butRenesas Electronics does notwarrantthatsuch information is error free. Renesas Electronics
assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions fromthe information included herein.
3. Renesas Electronics does not assume any liability for infringement ofpatents, copyrights,or other intellectual property rights ofthird parties by or arising from the use of Renesas Electronics products or
technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents,copyrights orotherintellectual property rights ofRenesas Electronics or
others.
4. You should not alter, modify,copy, orotherwise misappropriate any Renesas Electronics product, whether in whole or in part. Renesas Electronics assumes no responsibility for any losses incurred by you or
third parties arising from such alteration, modification, copy or otherwise misappropriation ofRenesas Electronics product.
5. Renesas Electronics products are classified according to the following two quality grades:"Standard" and "High Quality". The recommended applications foreach Renesas Electronics productdepends on
the product's quality grade,as indicated below.
"Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic
equipment; and industrial robots etc.
"High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; and safety equipment etc.
Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a directthreat to human life or bodily injury (artificial life supportdevices or systems, surgical
implantations etc.), or may cause serious property damages (nuclear reactor control systems,military equipment etc.). You mustcheck the quality grade of each Renesas Electronics product before using it
in a particular application. You may not use any Renesas Electronics product for any application for which it is not intended. Renesas Electronics shall not be in any way liable for any damages orlosses
incurred by you orthird parties arising from the use of any Renesas Electronics productfor which the product is notintended by Renesas Electronics.
6. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respectto the maximumrating, operating supply voltage
range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the
use of Renesas Electronics productsbeyond such specified ranges.
7. Although Renesas Electronics endeavors to improve the quality and reliability ofits products,semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and
malfunctions under certain use conditions. Further,Renesas Electronics products are notsubject to radiation resistance design. Please be sure to implementsafety measures to guard them against the
possibility ofphysical injury,and injury or damage caused by fire in the event ofthe failure of a Renesas Electronics product,such as safety design forhardware and software including but notlimited to
redundancy,fire control and malfunction prevention, appropriate treatment for aging degradation or any otherappropriate measures. Because the evaluation of microcomputersoftware alone is very difficult,
please evaluate the safety ofthe final products orsystems manufactured by you.
8. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility ofeach Renesas Electronics product. Please use Renesas Electronics
products in compliance with all applicable laws and regulations thatregulate the inclusion or use of controlled substances,including without limitation, the EU RoHS Directive. Renesas Electronics assumes
no liability fordamages orlosses occurring as a result ofyour noncompliance with applicable laws and regulations.
9. Renesas Electronics products and technology may notbe used foror incorporated into any products or systems whose manufacture, use,or sale is prohibited under any applicable domestic or foreign laws or
regulations. You should not use Renesas Electronics products ortechnology described in this document for any purpose relating to military applications or use by the military,including but notlimited to the
development ofweapons of mass destruction. When exporting the Renesas Electronics products or technology described in this document, you should comply with the applicable exportcontrol laws and
regulations and follow the procedures required by such laws and regulations.
10. Itis the responsibility ofthe buyeror distributor ofRenesas Electronics products,who distributes,disposes of,or otherwise places the productwith a third party,to notify such third party in advance of the
contents and conditions set forth in this document,Renesas Electronics assumes no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics
products.
11. This document may not be reproduced orduplicated in any form, in whole or in part,without prior written consentof Renesas Electronics.
12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document orRenesas Electronics products, orif you have any other inquiries.
(Note 1) "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries.
(Note 2) "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics.
http://www.renesas.com
Refer to "http://www.renesas.com/" for the latest and detailed information.
Renesas Electronics America Inc.
2880 Scott Boulevard Santa Clara, CA 95050-2554, U.S.A.
Tel: [phone], Fax: [phone]
Renesas Electronics Canada Limited
1101 Nicholson Road, Newmarket, Ontario L3Y 9C3, Canada
Tel: [phone], Fax: [phone]
Renesas Electronics Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K
Tel: [phone], Fax: [phone]
Renesas Electronics Europe GmbH
Arcadiastrasse 10, 40472 Düsseldorf, Germany
Tel: [phone], Fax: [phone]
Renesas Electronics (China) Co., Ltd.
7th Floor, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100083, P.R.China
Tel: [phone], Fax: [phone]
Renesas Electronics (Shanghai) Co., Ltd.
Unit 301, Tower A, Central Towers, 555 LanGao Rd., Putuo District, Shanghai, China
Tel: [phone], Fax: [phone]
Renesas Electronics Hong Kong Limited
Unit 1601-1613, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong
Tel: [phone], Fax: [phone]
Renesas Electronics Taiwan Co., Ltd.
13F, No. 363, Fu Shing North Road, Taipei, Taiwan
Tel: [phone], Fax: [phone]
Renesas Electronics Singapore Pte. Ltd.
80 Bendemeer Road, Unit #06-02 Hyflux Innovation Centre Singapore 339949
Tel: [phone], Fax: [phone]
Renesas Electronics Malaysia Sdn.Bhd.
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: [phone], Fax: [phone]
Renesas Electronics Korea Co., Ltd.
12F., 234 Teheran-ro, Gangnam-Gu, Seoul, 135-080, Korea
Tel: [phone], Fax: [phone]
SALES OFFICES
© 2013 Renesas Electronics Corporation. All rights reserved.
Colophon 3.0
Renesas Tools Website http://www.renesas.com/tools
All trademarks and registered trademarks are the property
of their respective owners.
If the requirements shown in the "CAUTION"
sentences are ignored,
the equipment may cause
personal injury or damage to the products.
© 2014 Renesas Electronics Corporation and Renesas Solutions Corp.
Colophon 3.0