Renfert Waxlectric light I User manual
#FEJFOVOHTBOMFJUVOH
*OTUSVDUJPONBOVBM߭.PEFEtFNQMPJ
*TUSV[JPOJEߤVTP߭*OTUSVDDJPOFTQBSBFMTFSWJDJP
ᜪ◅一⥢⩌߭瞦綣砞煿砖
.BEFJO(FSNBOZ
Waxlectric light I + II
Nr. 2150 / 2151
2011-08 21-6510 A
Ideas for dental technology
4FSJFOOVNNFS)FSTUFMMEBUVNVOE(FS¤UF7FSTJPOCFGJOEFOTJDIBVGEFN(FS¤UF5ZQFOTDIJME
4FSJBMOVNCFSBOEEBUFPGNBOVGBDUVSJOHBSFTIPXOPOUIFUZQFQMBUFPGUIFVOJU
-FOVN©SPEFT©SJFFUMBEBUFEFGBCSJDBUJPOTFUSPVWFOUTVSMBQMBRVFTJHOBM©UJRVFEFM࣌BQQBSFJM
*MOVNFSPEJTFSJFFMBEBUBDPTUSV[JPOFTJUSPWBOPTVMMBUBSHIFUUBEFMM࣌BQQBSFDDIJP
&MOºNFSPEFTFSJFZMBGFDIBEFGBCSJDBDJ³OFTU¡OJOEJDBEPTFOMBQMBDBJEFOUJGJDBEPSBEFMBQBSBUP
ᄴᅧᄟᅨ历㈓Ⴅ朙渼䐁აᄎჹ曡嶊ჴᅍᅵᄵᅤᅰჵ曡嶊ჴ㖧历㈓ᅦᅖᅨჱ栴津მᄒწᄄჟႦ
饝逭鰽螙錅麝黱鷽鸑銐蒱蒱錅麅鷁蒱蒱鷙鄆ꦑ鱑ꫝ饝誙鰵鸉餶襉襥
1 2
43
5 6
7 8
9 10
11 12
13 14
15 16
1817
2019
2221
23 24
1. Introduction
We are pleased with your decision to purchase
the Waxlectric light I or
Waxlectric light II-
dard with regard to functionality,
performance and safety.
Please read the following operating
instructions carefully and observe the
information they contain in order to
ensure a long and trouble-free service
life.
increases your safety during your daily work
with the Waxlectric light.
Waxlectric light is
its heater which is located directly in the mod-
elling tips. This allows the tips to react more
rapidly to temperature changes. The knife’s
friendly. The modelling tip surfaces are not
fault, only the tip need be replaced.
The wax knife no. 2155-0112, Large
Wax Knife (refer to “Accessories”)
may NOT be reground or
re-sharpened.
2. Application Area
The Waxlectric light is an electronically
2.1 Ambient Conditions
in Accordance with DIN EN 61010
The unit may only be operated:
-
proportionally in order to ensure operational readiness (e.g.,
-
3. Hazard Information
3.1 Symbology
Danger
This indicates a direct risk of injury.
Electrical current
This indicates a hazard due to
electrical current.
Attention
Hot surfaces.
Attention
Failure to observe the associated
information can result in damage to
the unit.
Note
This provides the operator with useful
information to make working with the
unit easier.
Only intended for indoor use.
Waxlectric light I + II
No. 2150 / 2151
ENGLISH
- 13 -
Observe the operating instructions.
3.2 Hazard Information
maximum operating temperature of 200°C
[392°F].
handle becomes very hot.
burns!
attention that the cables do not encounter
hot parts.
-
mable surface or cover it! Fire hazard!
-
ing modelling waxes.
hazards to the user!
-
vision
only designed for dry applications and
may not be operated or stored outdoors
or under wet conditions.
lines or other defects must be taken out of
service immediately.
-
eration.
moisture.
during operation (a rolled cord represents
an overheating hazard in case of short
circuits).
unit!
3.3 Liability Exclusion
for damages or warranty if:
-
es other than those cited in the operating
instructions;
than those alterations described in the
operating instructions;
authorized facility or if any but Renfert
despite obvious safety faults or
damage;
impacts or is dropped.
holder you must mount them on the control
unit:
-
- Tip holder:
Hook the retainer tabs of the tip holder into
the openings on the back of the control unit
-
ted on the underside of the control unit.
handpieces are connected to the correct
sockets. The handpieces are marked with
can also be found on the control unit’s opera-
The pins must audibly snap into the
sockets.
actual temperature at the
modelling tip.
5.4 Storing the Modelling Tips and
Handpieces
NEVER insert the handpieces into the
tip holder (Figure 15). This can dam-
age both the tip holder as well as the
control unit.
-
mable surface or cover it! Fire hazard!
-
Tips and Notes
-
-
-
through the guide rings towards the front of
control unit. The connecting socket is located
on the underside of the control unit (Figure
transformer to the mains power supply (Fig-
unit!
5. Operation
5.1 Operating Elements
(Figure 12)
(Waxlectric light II
5.2 Switching the Unit ON / OFF
switched on.
5.3 Temperature Adjustment
temperature setting.
NEVER attempt to heat the tips more
rapidly by holding them in an open
-
ling tip after heating up!
However, manufacturing tolerances
may result in minor differences
between the set temperature and the
- 15 -
Never rinse the unit off with water!
Do not use steam to clean the unit!
Hot steam penetrating the unit can
damage it.
from time-to-time.
Never use cleansers containing
solvents!
from burning onto the tip and maintain the tip’s
optimal heat conducting properties.
6.1 Changing Tips
Burn hazard!
The modelling tips may be hot. Always
allow the tips to cool before changing
them.
seated (Figure 17), the O-ring
provides a seal against the wax.
Modelling tips which are not being used can
be safely and handily stored in the tip holder
6.2 Cork Replacement
6.3 Cleaning the Quiver and Tip
Holder
-
installation instructions.
Refer to the spares list at the end of this manual
for numbers of wearing and replacement parts.
8. Disposal instructions for
countries in the EU
the recycling of raw materials, the European
the manufacturer to accept the return of elec-
trical and electronic units for proper disposal or
recycling.
symbol should not therefore be disposed of in
unsorted domestic waste:
For more information regarding proper disposal
please apply at your local authorities.
9. Warranty
wear, Renfert warrants the all components of
the Waxlectric light for a period of 3 years.
Warranty claims may only be made upon
presentation of the original sales receipt from
- 16 -
cleaning, maintenance, and connection instruc-
tions; in case of independent repairs or repairs
by unauthorized personnel; if spare parts from
other manufacturers are employed, or in case
-
pliance with the utilization instructions.
original warranty.
10. Technical
5 W (Waxlectric light I)
10 W (Waxlectric light II)
Min. operating temperature: 50°C [122°F]
Transformer:
11. Standard Delivery
1 Control unit
1 Handpiece (or 2 handpieces with the Wax-
lectric light II)
(for Waxlectric light I
(for Waxlectric light II)
1 Transformer
12. Delivery Versions
Waxlectric light I
Waxlectric light I
Waxlectric light II
Waxlectric light II
13. Accessories
Waxlectric
2155
-0101 -0102 -0103 -0104 -0105 -0106 -0107 -0108 -0109 -0110 -0111 -0112
14. Troubleshooting
Error Corrective action
LED B (Figure 12)
fails to go on.
switched on.
interrupted.
in the control unit.
required.
in place.
--> Replace with spare
Unit operating, but
no temperature at
the tip.
screwed in.
contaminated.
properly plugged into
the control unit.
cable shows signs of
corrosion.
socket until the cable locks in place.
required.
The tip fails to
reach the desired
temperature.
to the tip because the
supply unit is not being
used.
- 18 -
Other manuals for Waxlectric light I
8
This manual suits for next models
3
Table of contents
Other Renfert Laboratory Equipment manuals
Renfert
Renfert Basic Master Operating and installation instructions
Renfert
Renfert Twister pro User manual
Renfert
Renfert BASIC eco User manual
Renfert
Renfert SILENT EC2 Installation guide
Renfert
Renfert hotty User manual
Renfert
Renfert Silent TS2 User manual
Renfert
Renfert Catalyser 2300-0001 User manual
Renfert
Renfert Bijou 90 Series User manual
Renfert
Renfert Vario 3 User manual
Renfert
Renfert lay:art Mixing palette crystal User manual
Renfert
Renfert MT premium User manual
Renfert
Renfert Basic Quattro User manual
Renfert
Renfert Easyclean TEC Repair manual
Renfert
Renfert MT plus User manual
Renfert
Renfert MT3 User manual
Renfert
Renfert MT plus User manual
Renfert
Renfert MT premium User manual
Renfert
Renfert Safety Burner eco User manual
Renfert
Renfert 1826 User manual
Renfert
Renfert Catalyser 2300-0001 User manual
