Retekess T113S User manual

Queue Wireless Calling System
User Manual
T113S

Retekess T113S
Queue Wireless Calling System User Manual
200mAh
DC3.7V(200mAh Li-polymer battery)

DC 12V/2A power adapter

Button B
Button A
1. Use Operation
First, connect the host to power source by adapter, then insert the receiver into the charger slot.
Please program after 10min charging at least.
2. Program
Press button B while power on, LED2 and LED5 both light. Then input number on the keyboard,
and press “CALL”. The receiver beeps twice to indicate program is done.
3. Change Receiver’s Number
Repeat step 2, the original number will be replaced with new number. Previous number will be
cleared.
4. Remind Time
The remind time of the receiver is 30s.
5. Receiver Power ON/OFF
Hold button B till the receiver vibrates and indicator off, then release, receiver is power off. Press
button B or insert the receiver to host both can power on again.
Input 999 on the host and press button “CALL”, all charging receivers will be off. Unplug the host
power and re-power on again, all charging receivers will be on.
6. Change the pagers’ calling mode to silent mode
When the pagers are in the charging state, press the “998” button and the call button on the
keypad. The pagers in the charging state now are in the silent mode, it only flash and vibrate
when keypad call them. Press the "997" button and the call button on the keypad. The calling
mode of pagers which in the charging state will change to the ringing mode. When keypad call
them, the pagers flash, vibrate and beep.
Instructions
LED4
LED5
LED3
LED2

7. Working State of Receiver
Power Off State: All LED off.
Charging State: LED1 always on. Charging indicator is on when battery is full.
Standby State: LED1 flashes.
Reminding State: 5 LEDs flash, receiver vibrates and beeps. Press button A to stand by again.

RF ENERGY EXPOSURE AND PRODUCT SAFETY GUIDE
This radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications
between two or more users over a distance. RF energy, which when used improperly, can cause
biological damage.
All Retekess radios are designed, manufactured, and tested to ensure they meet government-established
RF exposure levels. In addition, manufacturers also recommend specific operating instructions to users
of the radios. These instructions are important because they inform users about RF energy exposure
and provide simple procedures on how to control it.
Please refer to the following websites for more information on what RF energy exposure is and how to
control your exposure to assure compliance with established RF exposure limits: http://www.who.int/en/
Local Government Regulations
When radios are used as a consequence of employment, the Local Government Regulations requires
users to be fully aware of and able to control their exposure to meet occupational requirements.
Exposure awareness can be facilitated by the use of a product label directing users to specific user
awareness information. Your Retekess radio has a RF Exposure Product Label. Also, your Retekess
user manual, or separate safety booklet includes information and operating instructions required to
control your RF exposure and to satisfy compliance requirements.
Radio License (if appropriate)
Governments keep the radios in classification, business radios operate on radio frequencies that are
regulated by the local radio management departments (FCC, ISED, OFCOM, ANFR, BFTK,
Bundesnetzagentur...).To transmit on these frequencies, you are required to have a license issued by
them. The detailed classification and the use of your radios, please contact the local government radio
management departments.
Use of this radio outside the country where it was intended to be distributed is subject to government
regulations and may be prohibited.
Precautions
Before using this radio, read this guide which contains important
operating instructions for safe usage and RF energy awareness
and control for compliance with applicable standards and regulations.

Unauthorized modification and adjustment
Changes or modifications not expressly approved by the party responsible for compliance may void the
user’s authority granted by the local government radio management departments to operate this radio
and should not be made. To comply with the corresponding requirements, transmitter adjustments
should be made only by or under the supervision of a person certified as technically qualified to perform
transmitter maintenance and repairs in the private land mobile and fixed services as certified by an
organization representative of the user of those services.
Replacement of any transmitter component (crystal, semiconductor, etc.) not authorized by the local
government radio management departments equipment authorization for this radio could violate the
rules.
FCC Requirements:
• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
• This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CE Requirements:
• (Simple EU declaration of conformity) Henan Eshow Electronic Commerce Co.,Ltd declares that the
radio equipment type is in compliance with the essential requirements and other relevant provisions of
RED Directive 2014/53/EU and the ROHS Directive 2011/65/EU and the WEEE Directive 2012/19/EU;
the full text of the EU declaration of conformity is available at the following internet address:
www.retekess.com.
• Disposal
The crossed-out wheeled-bin symbol on your product, literature, or packaging reminds you
that in the European Union, all electrical and electronic products, batteries, and accumulators
(rechargeable batteries) must be taken to designated collection locations at the end of their
working life. Do not dispose of these products as unsorted municipal waste. Dispose of them
according to the laws in your area.
IC Requirements:
Licence-exempt radio apparatus
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation
6

of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
RF Exposure Information
• DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may
also cause you to exceed RF exposure limits. A proper antenna is the antenna supplied with this radio
by the manufacturer or an antenna specifically authorized by the manufacturer for use with this radio,
and the antenna gain shall not exceed the specified gain by the manufacturer declared.
• DO NOT transmit for more than 50% of total radio use time, more than 50% of the time can cause RF
exposure compliance requirements to be exceeded.
• During transmissions, your radio generates RF energy that can possibly cause interference with other
devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to
do so.
• The device complies with RF specifications when the device used at 5mm from your body. Third-party
belt-clips, holsters, and similar accessories used by this device should not contain any metallic
components. Body-worn accessories that do not meet these requirements may not comply with RF
exposure requirements and should be avoided.
• DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as
hospitals, aircraft, and blasting sites.
Avoid Choking Hazard
Small Parts. Not for children under 3 years.
Protect your hearing:
• Use the lowest volume necessary to do your job.
• Turn up the volume only if you are in noisy surroundings.
• Turn down the volume before adding headset or earpiece.
• Limit the amount of time you use headsets or earpieces at high volume.
• When using the radio without a headset or earpiece, do not place the radio's speaker
directly against your ear
• Use careful with the earphone maybe possible excessive sound pressure
from earphones and headphones can cause hearing loss
Note: Exposure to loud noises from any source for extended periods of time may
temporarily or permanently affect your hearing. The louder the radio's volume, the less
time is required before your hearing could be affected. Hearing damage from loud
noise is sometimes undetectable at first and can have a cumulative effect.
Avoid Burns
Antennas
• Do not use any portable radio that has a damaged antenna. If a damaged antenna
comes into contact with the skin when the radio is in use, a minor burn can result.
WARNING
7

Batteries (If appropriate)
• When the conductive material such as jewelry, keys or chains touch exposed
terminals of the batteries, may complete an electrical circuit (short circuit the battery)
and become hot to cause bodily injury such as burns. Exercise care in handling any
battery, particularly when placing it inside a pocket, purse or other container with
metal objects
Long transmission
• When the transceiver is used for long transmissions, the radiator and chassis will
become hot.
Safety Operation
Forbid
• Do not use charger outdoors or in moist environments, use only in dry locations
/conditions.
• Do not disassemble the charger, that may result in risk of electrical shock or fire.
• Do not operate the charger if it has been broken or damaged in any way.
• Do not place a portable radio in the area over an air bag or in the air bag deployment
area. The radio may be propelled with great force and cause serious injury to
occupants of the vehicle when the air bag inflates.
To reduce risk
• Pull by the plug rather than the cord when disconnecting the charger.
• Unplug the charger from the AC outlet before attempting any maintenance or cleaning.
• Contact Retekess for assistance regarding repairs and service.
• The adapter shall be installed near the equipment and shall be easily accessible
• Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
• Adapter shall be installed near the equipment and shall be easily accessible.
• The plug considered as disconnect device of adapter.
• The operating temperature of the EUT can’t exceed the specified range.
Approved Accessories
• This radio meets the RF exposure guidelines when used with the Retekess
accessories supplied or designated for the product. Use of other accessories may
not ensure compliance with the RF exposure guidelines and may violate regulations.
• For a list of Retekess-approved accessories for your radio model, visit the following
website: http://www.Retekess.com
WARNING
WARNING
WARNING
EU Importer：
Name：Germany Retevis Technology GmbH
Address：Uetzenacker 29,38176 wendeburg
8