RFI CSA20-41-DIN User manual

COMPONENTS
BEFORE ASSEMBLING YOUR ANTENNA PLEASE ENSURE THAT ALL THE COMPONENTS BELOW ARE
INCLUDED IN THE KIT.
148-174 MHz
CSA20-41-DIN
M-8567
SCREEN CENTRE
QTY: 1
M-8567
SCREEN SIDES
QTY: 2
CORNER BRACKET
QTY: 12
M8x80 HEX HEAD BOLT
M8 FLAT WASHER
M8 FLAT WASHER
M8 SPRING WASHER
M8 HEX NUT
M8x80 BOLT ASSEMBLY
QTY: 24
LARGE CLAMP PLATE
QTY: 4
0A-20-41-DIN
DIPOLE ASSEMBLY
QTY: 1
M16 HEX NUT
M16 SPRING WASHER
M16 FLAT WASHER
M16x330 THREADED ROD
M16 STUD ASSEMBLY
QTY: 4
INS-40101-3 ©RF Industries Pty Ltd 2009
www.bird-technologies.com
PAGE 1 OF 4

148-174 MHz
SIDE SCREEN
SIDE SCREEN
CENTRE SCREEN
M8x80 BOLT ASSEMBLY
CORNER BRACKET
0A-20-41-DIN
DIPOLE ASSEMBLY
CENTRE SCREEN
M16 STUD ASSEMBLY
130
300
2MM (11.8")
TOP OF BOOM TO
TOP OF SCREEN
CSA20-41-DIN
ANTENNA ASSEMBLY
STEP 1:
ASSEMBLE THE 2 SIDE SCREENS TO THE CENTRE SCREEN AS DEPICTED BELOW USING THE 8 CORNER
BRACKETS AND THE 16 M8x80 BOLT ASSEMBLIES INCLUDED IN THE KIT.
TIGHTEN THE M8 BOLTS TO 25Nm (19 lbf.ft)
STEP 2:
ASSEMBLE THE DIPOLE TO THE CENTRE SCREEN AS DEPICTED BELOW USING THE 2 LARGE CLAMP PLATES
AND THE 4 M16 STUD ASSEMBLIES INCLUDED IN THE KIT. TIGHTEN THE M16 NUTS TO 70Nm (50 lbf.ft). LEAVE
APPROXIMATELY 130mm PROTRUDING OUT THE BACK SIDE.
INS-40101-3 ©RF Industries Pty Ltd 2009
www.bird-technologies.com
PAGE 2 OF 4

148-174 MHz
CSA20-41-DIN
MOUNTING TUBE
(NOT INCLUDED)
LARGE CLAMP PLATE
ANTENNA MOUNTING HARDWARE HAS BEEN
DESIGNED TO ACCEPT MOUNTING TUBE
DIAMETERS IN THE RANGE OF 75-115mm (3"- 4.5")
MOUNTING TUBE LENGTH TO BE SIZED BY
INSTALLER TO SUIT INSTALLATION METHOD.
PLEASE NOTE: MOUNTING POLE NOT SUPPLIED.
INS-40101-3 ©RF Industries Pty Ltd 2009
www.bird-technologies.com
PAGE 3 OF 4
ASSEMBLY INSTRUCTIONS continued
STEP 3:
WITH THE ANTENNA ASSEMBLY LOCATED ON THE MOUNTING TUBE ATTACH THE REMAINING 2 LARGE
CLAMP PLATES AND TIGHTEN THE M16 NUTS CLAMPING THE ANTENNA ASSEMBLY TO THE MOUNTING
TUBE. TIGHTEN TO 70Nm (50 lbf.ft)

148-174 MHz
CSA20-41-DIN
SCREENED ARRAY IS DESIGNED TO BE
FIXED TO A TOWER MOUNTED POLE
AND IS SUPPLIED WITH ALL NECESARY
HARWARE. (EXCLUDING THIS POLE AND
IT'S MOUNTING HARDWARE)
ENSURE THIS MOUNTING POLE, IT'S
CLAMPS AND THE MOUNTING
STRUCTURE ARE APPROPRIATELY SIZED
TO SUIT LOCAL WIND AND ICE
INSTALLATION CONDITIONS.
SCREENED ARRAY ASSEMBLY
CSA-20-41-DIN
MOUNT POLE
OUTRIGGER
TOWER
TOWER CLAMPS
STRAIN RELIEVE FEED CABLE BACK
TO SUPPORT STRUCTURE.
SEAL CONNECTOR WITH A SUITABLE
SELF AMALGAMATING TAPE.
TYPICAL
INSTALLATION
SIDE VIEW
THESE ITEMS
NOT INCLUDED
IN ANTENNA KIT:
ASSEMBLY INSTRUCTIONS continued
TYPICAL INSTALLATION
INS-40101-3 ©RF Industries Pty Ltd 2009
www.bird-technologies.com
PAGE 4 OF 4