RFI FSA10-41-DIN User manual

COMPONENTS
ASSEMBLY INSTRUCTIONS
Before assembling your antenna please confirm all the components below are included in the kit.
148-174 MHz
FSA10-41-DIN
SMALL CLAMP PLATE
QTY:1
M16x250 THREADED ROD
M16 FLAT WASHER
M16 HEX NUT
M16 SPRING WASHER
M16 STUD ASSEMBLY
QTY: 4
LARGE CLAMP PLATE
QTY: 2
M-8568
SCREEN
QTY: 1
M-8648
DIPOLE ASSEMBLY
QTY: 1
M8 FLAT WASHER
M8x130 HEX HEAD BOLT
M8 FLAT WASHER
M8 SPRING WASHER
M8 HEX NUT
M8x130 BOLT ASSEMBLY
QTY: 2
INS-40101-6 ©RF Industries Pty Ltd 2009
PAGE 1 OF 4
www.
RFIAmericas.com

148-174 MHz
M-8648
DIPOLE ASSEMBLY
DRAIN HOLE
SMALL CLAMP
PLATE
M8x130 BOLT
ASSEMBLY
243 +/-2MM (9.5")
SET DIPOLE
POSITION
M16 THREADED BAR
ASSEMBLY
150
FSA10-41-DIN
ANTENNA ASSEMBLY
STEP 1:
ASSEMBLE THE DIPOLE TO THE SCREEN AS DEPICTED BELOW ENSURING THE DIPLOLE TO SCREEN
SPACING IS SET CORRECTLY AND THE DRAIN HOLE IS FACING DOWNWARDS.
USING 2 OF THE 4 LARGE CLAMP PLATES AND THE 4 M16 STUD ASSEMBLIES INCLUDED IN THE KIT. TIGHTEN
THE M16 NUTS TO 70Nm (50 lbf.ft). LEAVE APPROXIMATELY 130mm PROTRUDING OUT THE BACK SIDE.
INS-40101-6 ©RF Industries Pty Ltd 2009
PAGE 2 OF 4
www.
RFIAmericas.com

ASSEMBLY INSTRUCTIONS continued
STEP 2:
WITH THE ANTENNA ASSEMBLY LOCATED ON THE MOUNTING TUBE ATTACH THE 2 LARGE CLAMP PLATES
AND TIGHTEN THE M16 NUTS CLAMPING THE ANTENNA ASSEMBLY TO THE MOUNTING TUBE. TIGHTEN TO
70Nm (50 lbf.ft)
148-174 MHz
FSA10-41-DIN
MOUNTING TUBE
(NOT INCLUDED)
LARGE CLAMP PLATE
ANTENNA MOUNTING HARDWARE HAS BEEN
DESIGNED TO ACCEPT MOUNTING TUBE
DIAMETERS IN THE RANGE OF 75-115mm (3"-4.5")
MOUNTING TUBE LENGTH TO BE SIZED BY
INSTALLER TO SUIT INSTALLATION METHOD.
PLEASE NOTE: MOUNTING POLE NOT SUPPLIED.
INS-40101-6 ©RF Industries Pty Ltd 2009
PAGE 3 OF 4
www.
RFIAmericas.com

148-174 MHz
FSA10-41-DIN
STRAIN RELIEVE FEED CABLE BACK
TO SUPPORT STRUCTURE.
SEAL CONNECTOR WITH A SUITABLE
SELF AMALGAMATING TAPE.
TOWER
OUTRIGGER
TOWER CLAMPS
MOUNT POLE
(THESE ITEMS NOT
SUPPLIED WITH ANTENNA)
SCREENED ARRAY ASSEMBLY
FSA-10-41-DIN
SCREENED ARRAY IS DESIGNED
TO BE FIXED TO A TOWER MOUNTED
POLE OR TOWER LEG.
ENSURE THAT MOUNTING POLE,
CLAMPS AND MOUNTING STRUCTURE
IS APPROPRIATELY SIZED TO SUIT
LOCAL
WIND AND ICE INSTALLATION
CONDITIONS.
TYPICAL
INSTALLATION
SIDE VIEW
ASSEMBLY INSTRUCTIONS continued
TYPICAL INSTALLATION
INS-40101-6 ©RF Industries Pty Ltd 2009
PAGE 4 OF 4
www.
RFIAmericas.com