RFI CSA20-67-DIN User manual

406-512 MHz
CSA20-67-DIN
M-8564
SCREEN CENTRE
QTY: 1
M-8564
SCREEN SIDES
QTY: 2
CORNER BRACKET
QTY: 8
0A-20-67-DIN
DIPOLE ASSEMBLY
QTY: 1
LARGE CLAMP PLATE
QTY: 4
M6 FLAT WASHER
M6x65 HEX HEAD BOLT
M6 FLAT WASHER
M6 SPRING WASHER
M6 HEX NUT
M6x65 BOLT ASSEMBLY
QTY: 24
M12 STUD ASSEMBLY
QTY: 4
M12 HEX NUT
M12 SPRING WASHER
M12 FLAT WASHER
M12x250 THREADED ROD
INS-40101-4 ©RF Industries Pty Ltd 2009
www.bird-technologies.com
PAGE 1 OF 4
COMPONENTS
BEFORE ASSEMBLING YOUR ANTENNA PLEASE ENSURE THAT ALL THE COMPONENTS BELOW ARE
INCLUDED IN THE KIT.

406-512 MHz
SIDE SCREEN
CENTRE SCREEN
SIDE SCREEN
M6x65 BOLT ASSEMBLY
CORNER BRACKET
0A-20-67
DIPOLE ASSEMBLY
CENTRE SCREEN
M12 STUD ASSEMBLY
90°
2.5
110
145
2MM (5.7")
TOP OF BOOM
TO TOP OF SCREEN
CSA20-67-DIN
ANTENNA ASSEMBLY
STEP 1:
ASSEMBLE THE 2 SIDE SCREENS TO THE CENTRE SCREEN AS DEPICTED BELOW USING THE 8 CORNER
BRACKETS AND THE 16 M6x65 BOLT ASSEMBLIES INCLUDED IN THE KIT. TIGHTEN THE M6 BOLTS TO 15Nm
(11 lbf.ft)
STEP 2:
ASSEMBLE THE DIPOLE TO THE CENTRE SCREEN AS DEPICTED BELOW USING THE 2 LARGE CLAMP PLATES
AND THE 4 M12 STUD ASSEMBLIES INCLUDED IN THE KIT. TIGHTEN THE M12 NUTS TO 55Nm (40 lbf.ft). LEAVE
APPROXIMATELY 110mm PROTRUDING OUT THE BACK SIDE.
INS-40101-4 ©RF Industries Pty Ltd 2009
www.bird-technologies.com
PAGE 2 OF 4

406-512 MHz
CSA20-67-DIN
MOUNTING TUBE
(NOT INCLUDED)
ANTENNA MOUNTING HARDWARE HAS BEEN
DESIGNED TO ACCEPT MOUNTING TUBE
DIAMETERS IN THE RANGE OF 50-75mm (2-3")
MOUNTING TUBE LENGTH TO BE SIZED BY
INSTALLER TO SUIT INSTALLATION METHOD.
PLEASE NOTE MOUNTING POLE NOT SUPPLIED.
LARGE CLAMP PLATE
INS-40101-4 ©RF Industries Pty Ltd 2009
www.bird-technologies.com
PAGE 3 OF 4
ASSEMBLY INSTRUCTIONS continued
STEP 3:
WITH THE ANTENNA ASSEMBLY LOCATED ON THE MOUNTING TUBE ATTACH THE REMAINING 2 LARGE
CLAMP PLATES AND TIGHTEN THE M12 NUTS CLAMPING THE ANTENNA ASSEMBLY TO THE MOUNTING
TUBE. TIGHTEN TO 55Nm (40 lbf.ft)

406-512 MHz
CSA20-67-DIN
SCREENED ARRAY IS DESIGNED TO BE
FIXED TO A TOWER MOUNTED POLE OR
TOWER LEG.
ENSURE THAT MOUNTING POLE,
CLAMPS AND MOUNTING STRUCTURE IS
APPROPRIATELY SIZED TO SUIT LOCAL
WIND AND ICE INSTALLATION
CONDITIONS.
TYPICAL
INSTALLATION
SIDE VIEW
STRAIN RELIEVE FEED CABLE BACK
TO SUPPORT STRUCTURE. SEAL
CONNECTOR WITH A SUITABLE SELF
AMALGAMATING TAPE.
TOWER
OUTRIGGER
TOWER CLAMPS
MOUNT POLE
SCREENED ARRAY ASSEMBLY
CSA-20-41-DIN
THESE ITEMS
NOT INCLUDED
IN ANTENNA KIT:
ASSEMBLY INSTRUCTIONS continued
TYPICAL INSTALLATION
INS-40101-4 ©RF Industries Pty Ltd 2009
www.bird-technologies.com
PAGE 4 OF 4