RH Baby&child AVALON STORAGE BUNK BED FULL OVER FULL User manual

Made in Vietnam
Distributed in the U.S.A. by:
Restoration Hardware Baby & Child
11640 Harrel St. Suite B
Mira Loma, CA 91752
www.rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7
WARNING: Read all instructions before assembling this product.
KEEP INSTRUCTIONS FOR FUTURE USE.
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to the address above. Include the
product model number, color, and a brief description of the part.
Call 1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft, dry cloth. Blot spills immediately and wipe
with a clean damp cloth. If the crib is to be stored, store in a cool dry place and carefully package all original hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Wrench (included)
Screwdriver (not included)
Note: It may be easier to assemble product with two people.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 12- 34of a turn. After bunks is
completely assembled, return to each bolt and tighten. Use wax or soap on all bolts to facilitate assembly.
AVALON FULL OVER FULL BUNK BED INSTRUCTIONS
RHBABY&CHILD
Page 1 of 9

IMPORTANT SAFETY INFORMATION FOR BUNK BED
1. Follow the information on the WARNINGS appearing on the upper bunk
end structure and on the carton.
2. Always use the specified size mattress, mattress support, or both to help
prevent the likelihood of entrapment or falls.
3. Surface of mattress must be at least 5 inches below the upper edge of
guardrails on top bunk.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
6. Periodically check and ensure that the guardrails, ladder, and other
components are in their proper position, free from damage, and that all
connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the
bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact Restoration Hardware for
replacement parts.
10.Use of a night light may provide added safety precaution for a child using
the upper bunk.
11.Use guardrails on both sides of the upper bunk.
12.If the bunk bed will be placed next to a wall, the guardrail that runs the full
length of the bed should be placed against the wall to prevent entrapment
between the bed and the wall.
13. The use of water flotation mattress is prohibited.
14.STRANGULATION HAZARD - Never attach or hang items to any part of
the bunk bed that are not designed for use with the bed: for example, but
not limited to, hooks, belts, and jump ropes
15.Keep these instructions for future reference.
7Flat Head Phillips Screw
(M4 x 20) 4 pcs.
NO. ITEM DESCRIPTION QTY.
1Threaded Rod 16 pcs.
2Curved Washer 16 pcs.
3Lock Washer 16 pcs.
4
5Wrench 1 pc.
Hex Nut 16 pcs.
6Round Head Screw
(M4 x 21mm) 68 pcs.
Page 2 of 9
WARNING
To help prevent serious or fatal injuries from entrapment
of falls:
·Never allow a child under 6 years on upper bunk.
·Use only mattress which is 74"-75" long and 52
1
2"-53 1 2" wide on upper bunk.
·Ensure thickness of mattress does not exceed 6"
and mattress is at least 5" below upper edge of
guardrails.
·Use guardrails on both sides of upper bunk.
·Prohibit horseplay on or under bed(s).
·Prohibit more than one person on upper bunk.
·Use ladder for entering and leaving upper bunk.
·STRANGULATION HAZARD - Never attach or
hang items to any part of the bunk bed that are not
designed for use with the bed; for example, but not
limited to, hooks, bells, and jump ropes.
DO NOT REMOVE THIS LABEL

COMPONENT IDENTIFICATION AND HARDWARE
E [10] BED SLATS
F [4] PLATFORM PANELS
G [1] LADDER
H [1] TRUNDLE
PARTS INCLUDED
A [1] HEADBOARD
B [1] FOOTBOARD
C [2] LOWER SIDE RAILS
D [2] UPPER SIDE RAILS
Page 3 of 9
B

ASSEMBLY INSTRUCTIONS
1. Lay the headboard (A) and the footboard (B) on a flat surface.
2. Attach the threaded rod (1) into the fixed nut in the post of the headboard/footboard by turning it manually. See FIGURE 1 and FIGURE 2.
IMPORTANT
These bed parts can be cumbersome and heavy to some people, therefore the assistance of two or more people is recommended in order to prevent
personal injury and ensure the bed parts are not damaged during the assembly process.
Page 4 of 9
Fig. 1
Fig. 1
Fig. 2
Fig. 2
Fig. 1
Fig. 1
Fig. 2
Fig. 2
FIGURE 1
1
FIGURE 2
1
A
B

FIGURE 4
2
3
4
5
2
3
4
5
FIGURE 3
Page 5 of 9
C
A
D
Fig. 3
Fig. 4
Fig. 3
Fig. 4
Honeycomb with total
thickness ~230mm
3. Hold the headboard (A) upright in the position you wish the bed to be in when fully assembled.
4. Align the threaded rods (1) on the headboard to the bore holes in the end of the lower side rail (C). Push the lower side rail up against the
headboard. On the other end of the lower side rail, insert honeycomb (total thickness is approximately 230mm) to level the lower side rail. You
may use honeycomb from packing material. The combination of 2 layers honeycomb 90thk and 1 layer honeycomb 50thk is recommended.
5. Install the hex nuts (4), curved washers (2) and the lock washers (3) on the threaded rods (1) to secure the lower side rail to the headboard. See
FIGURE 3.
6. Repeat step 4 and step 5 to attach the other lower side rail to the headboard.
7. Attach the upper side rails (D) to the headboard as per illustration in FIGURE
4. KEEP HOLDING THE UPPER SIDE RAILS WHILE DOING NEXT STEP.

8. Align the threaded rods (1) on the footboard (B) to the corresponding holes in the end of the lower side rails (C) and the upper side rails (D). Push
the footboard up against the side rails.
9. Repeat step 5, 6, and 7 to attach the side rails to the footboard.
Page 6 of 9
B
C
D
A
Honeycomb with total
thickness ~230mm

10. Set the bed slats (E) on the slat holders of the lower side rails (C) and the upper side rails (D). Secure each slat by using screw (6) provided.
See FIGURE 5.
11. Place the platform panels (F) on the lower bunk and the upper bunk, then fix them with screws (6). See FIGURE 6.
FIGURE 5
FIGURE 6
6
6
Page 7 of 9
E
Fig. 5
E
F
F
F
Fig. 6

NOTE: For the default setting, the ladder will be attached on the right side of the footboard (so
the guard rail is pre-attached on the left side of the footboard). If you want to attach the ladder on
the left side please unscrew and move the guard rail to right side of the footboard. Re-install the
screws and metal bracket to secure the guard rail. See illustration in FIGURE 7 and FIGURE 8.
FIGURE 7
FIGURE 8
Metal bracket
Page 8 of 9
Fig. 7
Fig. 8
Fig. 8
Fig. 8
Fig. 8
Fig. 7
Guard rail

12. Hook the ladder (G) on the footboard then secure it with screws (7) as per illustration in FIGURE 9 and FIGURE 10.
13. Slide the trundle (H) underneath the bunk bed as in FIGURE 11. Assembly is complete.
OPTION 1 OPTION 2
7
FIGURE 9
no screw
FIGURE 10
7
H
FIGURE 11
Page 9 of 9
Fig. 9
Fig. 10
G