RH Baby&child 487026 User manual

HAND-CARVED DISPLAY SHELF - LARGE
PARTS ENCLOSED:
(A) Hand-Carved Display Shelf - Large
(B) [3] Plastic Anchor – (1 Extra Included)
(C) [3] Screw – (1 Extra Included)
IMPORTANT SAFTEY INSTRUCTIONS:
•Stud mounting recommended. Use proper hardware
for your wall type (such as plastic anchors for dry
walls). When in doubt, consult your local hardware
store.
•For your safety, it is strongly recommended that
two people hang this product.
•These instructions are provided for your safety. It is
important that they are read carefully and completed
before installation of the fixture.
TO ASSEMBLE:
1. Unpack all parts and place them on a protected
work surface.
2. Hold product at desired location. With a pencil,
mark on wall the top outside corners. These marks
will be used to determine the location of your
mounting hardware.
3. Measure down from top of the Hand-carved
Display Shelf to the top of both keyhole notches.
Record these measurements on the wall, using the
marks in step one as a guide.
4. Measure in from the side of the Hand-carved
Display Shelf to the top of both keyhole notches.
Again, record these measurements on the wall.
Align the two measurements until they intersect.
This is the insertion point of your mounting
hardware. Use a level to ensure the item will be
straight.
5. Insert screws into wall, leaving approximately ½”
between the back of the screw head and the wall.
6. Align keyhole notches over the screw heads.
7. Slide Hand-carved Display Shelf down until the top
keyhole rests on the screws. Tighten or loosen
screws as needed to fit them snugly against wall.
CARE INSTRUCTIONS:
•To clean, wipe gently with a soft dry cloth.
•Avoid the use of harsh chemicals or abrasive
cleaners as they may damage the finish.

HAND-CARVED DISPLAY SHELF - MEDIUM
PARTS ENCLOSED:
(A) Hand-Carved Display Shelf - Medium
(B) [3] Plastic Anchor – (1 Extra Included)
(C) [3] Screw – (1 Extra Included)
IMPORTANT SAFTEY INSTRUCTIONS:
•Stud mounting recommended. Use proper hardware
for your wall type (such as plastic anchors for dry
walls). When in doubt, consult your local hardware
store.
•For your safety, it is strongly recommended that
two people hang this product.
•These instructions are provided for your safety. It is
important that they are read carefully and completed
before installation of the fixture.
TO ASSEMBLE:
1. Unpack all parts and place them on a protected
work surface.
2. Hold product at desired location. With a pencil,
mark on wall the top outside corners. These marks
will be used to determine the location of your
mounting hardware.
3. Measure down from top of the Hand-carved
Display Shelf to the top of both keyhole notches.
Record these measurements on the wall, using the
marks in step one as a guide.
4. Measure in from the side of the Hand-carved
Display Shelf to the top of both keyhole notches.
Again, record these measurements on the wall.
Align the two measurements until they intersect.
This is the insertion point of your mounting
hardware. Use a level to ensure the item will be
straight.
5. Insert screws into wall, leaving approximately ½”
between the back of the screw head and the wall.
6. Align keyhole notches over the screw heads.
7. Slide Hand-carved Display Shelf down until the top
keyhole rests on the screws. Tighten or loosen
screws as needed to fit them snugly against wall.
CARE INSTRUCTIONS:
•To clean, wipe gently with a soft dry cloth.
•Avoid the use of harsh chemicals or abrasive
cleaners as they may damage the finish.

HAND-CARVED DISPLAY SHELF - SMALL
PARTS ENCLOSED:
(A) Hand-Carved Display Shelf - Small
(B) [3] Plastic Anchor – (1 Extra Included)
(C) [3] Screw – (1 Extra Included)
IMPORTANT SAFTEY INSTRUCTIONS:
•Stud mounting recommended. Use proper hardware
for your wall type (such as plastic anchors for dry
walls). When in doubt, consult your local hardware
store.
•For your safety, it is strongly recommended that
two people hang this product.
•These instructions are provided for your safety. It is
important that they are read carefully and completed
before installation of the fixture.
TO ASSEMBLE:
1. Unpack all parts and place them on a protected
work surface.
2. Hold product at desired location. With a pencil,
mark on wall the top outside corners. These marks
will be used to determine the location of your
mounting hardware.
3. Measure down from top of the Hand-carved
Display Shelf to the top of both keyhole notches.
Record these measurements on the wall, using the
marks in step one as a guide.
4. Measure in from the side of the Hand-carved
Display Shelf to the top of both keyhole notches.
Again, record these measurements on the wall.
Align the two measurements until they intersect.
This is the insertion point of your mounting
hardware. Use a level to ensure the item will be
straight.
5. Insert screws into wall, leaving approximately ½”
between the back of the screw head and the wall.
6. Align keyhole notches over the screw heads.
7. Slide Hand-carved Display Shelf down until the top
keyhole rests on the screws. Tighten or loosen
screws as needed to fit them snugly against wall.
CARE INSTRUCTIONS:
•To clean, wipe gently with a soft dry cloth.
•Avoid the use of harsh chemicals or abrasive
cleaners as they may damage the finish.