RH Baby&child 355-95 User manual

NOTE:
- Bed must be assembled by at least two people.
- Please read instruction carefully before
assembling bed.
- Use the parts and fittings list to identify each
component.
- Keep all packing materials until assembly is
complete to avoid loss of smaller parts.
- Do not completely tighten all bolts until all
steps are finished.
PARTS INCLUDED:
A
B
C
D
E
TOOLS NEEDED:
Phillips-head screwdriver (not included)
SIDE FRAME
SLAT ROLL
SIDE RAIL
CENTER STRETCHER
SIDE STRETCHER
[2]
[1]
[2]
[1]
[2]
Page 1 of 5
1
2
3
4
5
6
7
8
9
Long Bolt 5/16”x 2-1/4”
Multi Wrench 12mm
2 pcs.
2 pcs.
2 pcs.
4 pcs.
1 pc.
4 pcs.
1 pc.
4 pcs.
4 pcs.
Flat Washer 5/16”
Spring Washer 5/16”
Hex Nut 5/16”x 12mm
Allen Key 4mm
Screws 8 x 30mm
10
11
6 pcs.
2 pcs.
Extra Metal Bracket
Extra Long Screws
7 x 35mm
Threaded Rod
5/16”x2-3/4”
NO. ITEM DESCRIPTION QTY.
ASSEMBLY INSTRUCTIONS:
STEP 1:
Insert the Threaded Rods (5) into the posts of the Side
Frames (A).
Curved Slotted Washer
35 x 16 x 12 x 3 mm
COLE FRAMED TWIN/FULL BED – ASSEMBLY INSTRUCTIONS
Model No: 355 - 95/96

Page 2 of 5
STEP 2:
- Slide the Side Rails (C) onto the Side Frames (A).
- Insert Curved Slotted Washer (8), and Hex Nut (7), and
tighten with Multi Wrench (9).
- Do not tighten bolts completely at this time, in
order to leave room for installation of Stretcher (E)
hooks (next step).
STEP 3:
2 people are needed to assemble Stretcher (E). At the
same time, insert the 2 stretchers into the metal
brackets on the post of Side Frame (A). Slightly push
the stretchers down to be flush with posts.
DO NOT MOVE THE BED AT THIS STAGE.
Please always have 2 people move the bed at the same
time if it needs moving.
COLE FRAMED TWIN/FULL BED – ASSEMBLY INSTRUCTIONS
Model No: 355 - 95/96

Page 3 of 5
EE
E
(10)
(11)
E
Phillips-head
screwdriver.
Phillips-head
screwdriver.
INSTRUCTIONS TO REPLACE METAL BRACKETS IF NEEDED:
If the metal bracket malfunctions or becomes damaged, please replace it with an extra metal bracket.
Unscrew the wooden screws with a Phillips-head screwdriver, then remove the damaged Metal Bracket.
Install the new Metal Bracket (11) to the top of
Side Stretcher (E) using new Wood Screws (10).
Tighten the screws with a Phillips-head screwdriver.
COLE FRAMED TWIN/FULL BED – ASSEMBLY INSTRUCTIONS
Model No: 355 - 95/96

Page 4 of 5
STEP 4:
Insert the Center Stretcher (D) onto the top of Side Frames
(A) by using Long Bolts (1), Spring Washers (2), Flat
Washers (3), and use Allen Key (4) to tighten.
Also tighten all side rail bolts.
STEP 5:
Lay the Slat Roll (B) between the Side Rails (C) and
attach using Screws (6) with Phillips-head screwdriver
(not provided).
COLE FRAMED TWIN/FULL BED – ASSEMBLY INSTRUCTIONS
Model No: 355 - 95/96

Page 5 of 5
STEP 6:
If needed, adjust the levelers underneath the posts of
the Side Frame (A).
Note: Maximum loading
- Single/Twin 500 lbs.
- Queen/King/Full 800 lbs
COLE FRAMED TWIN/FULL BED – ASSEMBLY INSTRUCTIONS
Model No: 355 - 95/96
CARE INSTRUCTIONS:
1. DUST OFTEN USING A CLEAN, SOFT, DRY LINT- FREE CLOTH.
2. BLOT SPILLS IMMEDIATELY AND WIPE WITH A CLEAN, DAMP CLOTH.
3. DO NOT USE CHEMICAL CLEANSERS, ABRASIVES OR FURNITURE POLISH ON THE LACQUERED FINISH.