RH Baby&child KEEGAN TWIN User manual

Page 1 of 13
KEEGAN TWIN/FULL LOW BUNK BED
Made in Vietnam
Model No: 0337 - 8/9
Distributed in the U.S.A by:
RH Baby&Child
2900 N MACARTHUR DRIVE
TRACY, CA 95376
www.rhbabyandchild.com
Distributed in Canada by:
RH Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia
V6E4N7
WARNING: Read all
Instructions before assembling
this product.
KEEP INSTRUCTIONS FOR
FUTURE USE.
CUSTOMER SERVICE
If you are missing partsor have any questions about this product, contact us first. You can also order parts by writing to
the address above. Include the product model number, color, and a brief descriptionof the part.Or call 1-800-762-1751.
CARE AND CLEANING
TOOLS AND INSTALLATION
Tools needed: Key Wrench (included).
Two people are recommended for assembly.
When inserting bolts, turn clockwise until tight. Then loosen 1/2-3/4 of aturn. After bed is completely assembled,
return to each bolt and tighten.
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning.If the crib is to be stored, store in a cool,
dry place and carefully package all original hardware to protect from loss.

KEEGAN TWIN/FULL LOW BUNK BED
Page 2 of 13
IMPORTANT SAFETY INFORMATION FOR BUNK BED
-
1. Follow the information on the WARNINGS appearing on the upper bunk end structure and on the
carton. DO NOT REMOVE WARNING LABEL FROM BED.
2. Always use the specified size mattress or mattress support, or both to help prevent the likelihood of
entrapment or falls.
3. Surface of mattress must be at least 5 inches below the upper edge of guardrails on top bunk.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
6. Periodically check and ensure that the guardrails, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact Restoration Hardware for replacement parts
10. Use of a night light may provide added safety precaution for a child using the upper bunk.
11. Use guardrails on both sides of the upper bunk.
12. If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed
should be placed against the wall to prevent entrapment between the bed and the wall.
13. The use of water flotation mattresses is prohibited.
14. STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are
not designed for use with the bed: for example, but not limited to, hooks, belts, and jump ropes.
15. Keep these instructions for future reference.
TO HELP PREVENT SERIOUS OR FATAL INJURIES FROM
ENTRAPMENT OR FALLS
1. Never allow a child under 6 years on upper bunk.
2. - If bunk is Twin/Twin:
Use only mattress which is 75" long and 38" wide and 7" height on upper bunk,
and mattress which is 75" long and 38" wide and 7" height on lower bunk.
- If bunk is Full/Full:
Use only mattress which is 75" long and 53" wide and 7" height on upper bunk,
and mattress which is 75" long and 53" wide and 7" height on lower bunk.
3. Ensure thickness of mattress does not exceed 7"and mattress surface is at least
5 inches below upper edge of guardrails. Thickness for lower bunk is 7” high.
4. Use guardrails on both sides of upper bunk.
5. Prohibit horseplay on or under bed(s).
6. Prohibit more than one person on upper bunk.
7. Use ladder for entering and leaving upper bunk.
8. If the bunk bed will be placed next to a wall the guardrails that run the full length
of the bed should be placed against the wall to prevent entrapment between
the bed and the wall.
STRANGULATION HAZARD
9. Never attach or hang items to any part of the bunk bed that are not designed for
use with the bed, for example, but not limited to hooks, belts, and jump ropes.
DO NOT REMOVE THIS LABEL
WARNING

HARDWARE INCLUDED
1
2
3
4
4 pcs.
Long Bolt 5/16" x 2-3/4"
1 pc.
1 pc.
4 pcs.
Key Wrench 4mm
Key Wrench 5mm
NO. ITEM DESCRIPTIONQTY.
PARTS IDENTIFICATION
Page 3 of 13
(A) Headboard/ Footboard
(x2 pieces)
(E) Front Side Rail (x2 pieces)
(H) Slat Roll (x1 set)
(F) Stretcher Bars (x4 pieces)
(G) Top Platform Panels (x2 pieces)
(B) Ladder (x1 piece)
(C) Long Side Rails (x1 piece) (D) Short Side Rail (x1 piece)
Half Moon Washer
KEEGAN TWIN/FULL LOW BUNK BED

Page 4 of 13
TOOLS NEEDED
Phillips-head screwdriver (not included)
5
6
7
8
9
10
11
12
14
13
6 pcs.
6 pcs.
Twin = 28 pcs.
Full = 32 pcs.
48 pcs.
8 pcs.
8 pcs.
8 pcs.
1 pc.
Short Screw 8 x 20mm
Long Screw 8 x 30mm
4 pcs.
Middle Screw 8 x 25mm
3 pcs.Metal Bracket
Connecting Bolt
Camlock Wheel
Threaded Rod 5/16"x 3"
Hex Nut 5/16"x 12mm
Hex Wrench 12mm
Curved Slotted Washer 5/16"
KEEGAN TWIN/FULL LOW BUNK BED – ASSEMBLY INSTRUCTIONS
Model No: 0337 - 8/9

ASSEMBLY INSTRUCTIONS
Note: - Bed must be assembled by at least two people.
- Please read instructions carefully before assembling bed.
- Use the parts and fittings list to identify each component.
- Keep all packing materials until assembly is complete to avoid loss of smaller parts.
- Do not completely tighten all bolts until all steps are finished.
NOTE:
The bunk has total of 2 orientations. Ladder (B) can be attached to left or right of the bunk bed, depending on where you would
like the Ladder (B) to be positioned (use options below).
SHORT SIDE RAIL CAN BE CONVERT TO LEFT OR RIGHT OF THE BUNK:
Page 5 of 13
D
Orientation 1 Orientation 2
Orientation 1 Orientation 2
D
D
D
B
B
KEEGAN TWIN/FULL LOW BUNK BED

Page 6 of 13
D
TO CONVERT THE SHORT SIDE RAIL, FOLLOW THESE BELOW STEPS:
1. Remove the panel from the Short Side Rail (D),
by unscrew the bolt/screws found on the side rail.
2. Then remove metal bracket from the panel by
unscrew the screws found on the panel.
3. Re-attach the metal bracket to the panel
by the original screws, as seen below.
KEEGAN TWIN/FULL LOW BUNK BED
1

Page 7 of 13
STEP 1:
4. Re-attach the panel to the Side Rail by the
original bolt/screws.
- Tighten all bolt/screws using Allen Key (1) and
Phillips-head screwdriver (not included).
7
A
A
7
KEEGAN TWIN/FULL LOW BUNK BED
Insert the Threaded Rod (7) into
the Headboard/Footboard (A).
1

Slide the Long Side Rail (C) and Front Side Rails (E)
to either the Headboard/Footboard (A).
Insert Curved Slotted Washers (8), and Hex Nut (9),
and tighten with Multi Wrench (10).
Page 8 of 13
STEP 2:
7
10
8
9
A
C
A
E
E
KEEGAN TWIN/FULL LOW BUNK BED

Page 9 of 13
STEP 3:
STEP 4:
Secure the Stretcher Bars (F) to the Long/Short
Side Rails (C, D) aligning Connecting Bolt (5) into
the hole of assembling insert on the Stretcher
Bars (F).
Assembling insert
D
F
C
C
D
5
5
KEEGAN TWIN/FULL LOW BUNK BED
Insert the Connecting Bolts (5) into the
Long/Short Side Rails (C, D).

STEP 5:
Page 10 of 13
Attach the Long/Short Side Rails (C, D)
to the Headboard/Footboard (A) by using
Long Bolt (2), Half Moon Washer (3) and
tighten with Allen Key (1).
STEP 6:
Attach Metal Brackets (14) to the Long/Short
Side Rails (C, D) and Headboard/Footboard (A)
using Short Screws (11), and tighten with
Phillips-head screwdriver (not included).
14
3
1
2
11
KEEGAN TWIN/FULL LOW BUNK BED