RH Teen KIERAN 0288-12/13 User manual

KIERAN STUDY LOFT BED
Page 1 of 11
Made in Vietnam
Model No: 0288 - 12/13
Distributed in the U.S.A by:
RH Baby&Child
2900 N MACARTHUR DRIVE
TRACY, CA 95376
www.rhbabyandchild.com
Distributed in Canada by:
RH Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia
V6E4N7
WARNING: Read all
Instructions before assembling
this product.
KEEP INSTRUCTIONS FOR
FUTURE USE.
CUSTOMER SERVICE
If you are missing partsor have any questions about this product, contact us first. You can also order parts by writing to
the address above. Include the product model number, color, and a brief descriptionof the part.Or call 1-800-762-1751.
CARE AND CLEANING
TOOLS AND INSTALLATION
Tools needed: Key Wrench (included).
Two people are recommended for assembly.
When inserting bolts, turn clockwise until tight. Then loosen 1/2-3/4 of aturn. After bed is completely assembled,
return to each bolt and tighten.
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning.If the crib is to be stored, store in a cool,
dry place and carefully package all original hardware to protect from loss.

Page 2 of 11
-
KIERAN STUDY LOFT BED
-
IMPORTANT SAFETY INFORMATION FOR BUNK BED
1. Follow the information on the WARNINGS label appearing on the upper bunk end structure and on the
box. DO NOT REMOVE WARNING LABEL FROM BED.
2. Always use the specified mattress size, or mattress support, or both to help prevent the likelihood of
entrapment or falls.
3. Surface of mattress must be at least 5 inches below the upper edge of guardrails on top bunk.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
6. Periodically check and ensure that the guardrails, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact Restoration Hardware for replacement parts.
10. Use of a nightlight may provide added safety precaution for a child using the upper bunk.
11. Use guardrails on both sides of the upper bunk.
12. If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed
should be placed against the wall to prevent entrapment between the bed and the wall.
13. The use of water flotation mattresses is prohibited.
14. STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are
not designed for use with the bed, such as hooks, belts, and jump ropes.
15. Keep these instructions for future reference.
TO HELP PREVENT SERIOUS OR FATAL INJURIES FROM
ENTRAPMENT OR FALLS
1. Never allow a child under 6 years of age on upper bunk.
2. - If bunk is Twin/Twin:
Only use a mattress that is 75" long, 38" wide and 7" high on upper bunk,
and a mattress that is 75" long, 38" wide and 10" high on lower bunk.
- If bunk is Full/Full:
Only use a mattress that is 75" long, 53" wide and 7" high on upper bunk,
and a mattress that is 75" long, 53" wide and 10" high on lower bunk.
3. Ensure thickness of mattress does not exceed 7" and mattress surface is at least
5" below upper edge of guardrails. Thickness for lower bunk is 10" high.
4. Use guardrails on both sides of upper bunk.
5. Prohibit horseplay on or under bed(s).
6. Prohibit more than one person on upper bunk.
7. Use ladder for entering and leaving upper bunk.
8. If the bunk bed will be placed next to a wall, the guardrails that run the full length
of the bed should be placed against the wall to prevent entrapment between
the bed and the wall.
STRANGULATION HAZARD
9. Never attach or hang items to any part of the bunk bed that are not designed for
use with the bed, such as hooks, belts, and jump ropes.
DO NOT REMOVE THIS LABEL
WARNING

PARTS IDENTIFICATION
Page 3 of 11
(B) Footboard (x1 piece)
(A) Headboard (x1 piece)
(E) Shelf Panels (x4 pieces)
(C) Long Guard Rail (x1 piece) (D) Front Guard Rail (x1 piece)
(F) Support Bars (x4 pieces)
(G) Top Platform Panels (x2 pieces) (H) Ladder (x1 piece)
KIERAN STUDY LOFT BED

Page 4 of 11
HARDWARE INCLUDED
TOOLS NEEDED
Phillips-head screwdriver (not included)
ASSEMBLY INSTRUCTIONS
Note: - Bed must be assembled by at least two people.
- Please read instructions carefully before assembling bed.
- Use the parts and fittings list to identify each component.
- Keep all packing materials until assembly is complete to avoid loss of smaller parts.
- Do not completely tighten all bolts until all steps are finished.
1
2
3
4
5
6
7
8
9
10
3 pieces
1 piece
28 pieces
Long Bolt 5/16"x 2-1/2"
4 pieces
4 pieces
4 pieces
48 pieces
1 piece
4 pieces
Long Screw 8 x 30mm
Short Screw 7 x 15mm
2 pieces
Middle Screw 8 x 19mm
Key Wrench 4mm
NO. ITEM DESCRIPTIONQTY.
Small Bolts 1/4"x 5/8"
Threaded Rod 5/16"x 2-1/2"
Curved Slotted Washer
5/16"x 30 x 15 x 2mm
Hex Nut
5/16"x 12 x 12mm
12 mm Hex Wrench 12mm
KIERAN STUDY LOFT BED

Page 5 of 11
STEP 2:
STEP 1:
E
A
B
A
B
KIERAN STUDY LOFT BED
Lay the Shelf Panels (E) into the Headboadr (A)
and the Footboard (B) (as seen below).
Insert the Threaded Rods (4) into the posts of
Headboard/Footboard (A, B), (as seen below).
4
4
45mm

Page 6 of 11
STEP 3:
STEP 4:
C
D
4
Lay the Long Guard Rail (C), Front Guard Rail (D),
to the posts of the headboard /footboard
(as seen below).
KIERAN STUDY LOFT BED
Attach the Shelf panels (E) to the
Headboadr (A) and the Footboard (B)
using 28 Short Screws (9), and
tighten with Phillips-head screwdrive
(not included).
9 (x28 pcs.)

Page 7 of 11
STEP 5:
2
1
654
3
1
10
Attach the Long Guard Rail (C) and Front Guard
Rail (D) on top the posts of headboard/footboard,
using Small Bolts (2) and tighten with Allen Key (1).
STEP 6:
Insert Long Bolts (3) and tighten with Allen Key (1).
Then, insert Curved Slotted Washers (5), and Hex
Nut (6) to Threaded Rod (4), and tighten with Hex
Wrench (10) (as seen below).
KIERAN STUDY LOFT BED
CD

STEP 7:
Page 8 of 11
Position the Ladder (H) in the opening between
the Front Guard Rail (D) and Footboard (B).
Hook the Ladder (H) over the cross bar of Front
Guard Rail (D) and Right Leg of Footboard (B).
Insert the 2 Middle Screws (8), and tighten
with Phillips-head screwdrive (not included).
8
H
B
HD
B
H
KIERAN STUDY LOFT BED

STEP 9:
Page 9 of 11
STEP 8:
Lay the Support Bars (F) between the Long
Guard Rail (C) and Front Guard Rail (D), using
Long Screws (7) and tighten with Phillips -
head screwdriver (not included).
Phillips-head
screwdriver.
F
7
F
G
Lay the Top Platform Panels (G) on top of the
Support Bars (F) and attach using Qty.40 pcs
Long Screws (7) with Phillips-head screwdriver.
7 (x40 pcs.)
KIERAN STUDY LOFT BED

Page 10 of 11
After the bunk bed is completely assembled,
return to each bolt and tighten to snug fit.
DO NOT over tighten.
WARNING:
Can be adjusted
by using leveler.
KIERAN STUDY LOFT BED

Page 11 of 11
KIERAN STUDY LOFT BED
STEP 10:
INSTALL MATTRESS
UPPER BUNK MATTRESS DIAGRAM
MATTRESS
MATTRESS SPECIFICATIONS FOR TOP BUNK:
The following size mattress and foundation are specified for use with this bunk bed:
MATTRESS DIMENSION SPECIFICATIONS FOR TOP BUNK
Twin-Over-Twin bunk: 75" long x 38" wide x 7" high
Full-Over-Full bunk: 75" long x 53" wide x 7" high
MATTRESS DIMENSION SPECIFICATIONS FOR LOWER BUNK
Twin-Over-Twin bunk: 75" long x 38" wide x 10" high
Full-Over-Full bunk: 75" long x 53" wide x 10" high
PLATFORM :
- Twin-Over-Twin bunk: Upper bed consists of 2 platform pieces 37 3/4" long x 38 3/4" wide x 3/4" high and bottom bed consists of
14 slats 38 3/4" long x 2 1/2" wide x 3/4" high.
- Full-Over-Full Bunk: Upper bed consists of 2 platform pieces 37 3/4" long x 53 7/8" wide x 3/4" high and bottom bed consists of
14 slats 53 7/8" long x 2 1/2" wide x 3/4" high.
**Note: MATTRESS THICKNESS MUST NOT EXCEED 7" HEIGHT FOR TOP BUNK.
Be sure to adhere to these MATTRESS SPECIFICATIONS in order to avoid the possibility of falling or entrapment.
THESE SPECIFICATIONS MUST BE STRICTLY ADHERED TO!
5" MINIMUM DISTANCE
FROM TOP OF MATTRESS
TO TOP OF GUARD RAIL
7" MAXIMUM
THICKNESS
SIDE RAIL
PLATFORM
CARE INSTRUCTIONS
Dust often using a clean, soft, dry, lint-free cloth.
Blot spills immediately, and wipe with a clean, damp cloth.
Do not use chemical cleansers, abrasives or furniture polish on the lacquered finish.