RH Teen KIERAN STUDY BUNK 0288-12 User manual

Made in Vietnam
Distributed in the U.S.A by:
Restoration Hardware Baby & Child
11640 Harrel St. Suite B
Mira Loma, CA 91752
www.rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7
Model No: 0288 - 12/ 13
KIERAN STUDY BUNK BED TWIN/ FULL
WARNING: Read all
Instructions before assembling
this product.
KEEP INSTRUCTIONS FOR
FUTURE USE.
Page 1 of 11
CUSTOMER SERVICE
If you are missing partsor have any questions about this product, contact us first. You can also order parts by writing to
the address above. Include the product model number, color, and a brief descriptionof the part.Call 1-800-762-1751.
CARE AND CLEANING
TOOLS AND INSTALLATION
Tools Necessary: Key Wrench (included).
NOTE : It may be easier to assemble productwith two people.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 1/2-3/4 of aturn. After crib is completely assembled,
return to each bolt and tighten.
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning.If the crib is to be stored, store in a cool
dry place and carefully package all original hardware to protect from loss.
All Restoration Hardware bunk bed are designed to meet the highest safety
standards and comply with all U.S. and Canadian bunk bed and cradles regulations.

Page 2 of 11
IMPORTANT SAFETY INFORMATION FOR BUNK BED
-
TO HELP PREVENT SERIOUS OR FATAL
INJURIES FROM ENTRAPMENT OR FALLS
1. Never allow a child under 6 years on upper bunk.
2. Use only mattress, which is 74"-75" long and
37 1/2"-38 1/2" wide (TWIN BUNK) or 74"-75"
long and 53 1/2"-54 1/2" wide (FULL BUNK)
on upper bunk.
3. Ensure thickness of mattress does not exceed 6"
and mattress surface is at least 5 inches below
upper edge of guardrails.
4. Use guardrails on both sides of upper bunk.
5. Prohibit horseplay on or under bed(s).
6. Prohibit more than one person on upper bunk.
7. Use ladder for entering and leaving upper bunk.
8. If the bunk bed will be placed next to a wall the
guardrails that run the full length of the bed
should be placed against the wall to prevent
entrapment between the bed and the wall.
STRANGULATION HAZARD
9. Never attach or hang items to any part of the
bunk bed that are not designed for use with the
bed, for example, but not limited to hooks, belts,
and jump ropes.
DO NOT REMOVE THIS LABEL
1. Follow the information on the WARNINGS appearing on the upper bunk end structure and on the
carton. DO NOT REMOVE WARNING LABEL FROM BED.
2. Always use the specified size mattress or mattress support, or both to help prevent the likelihood of
entrapment or falls.
3. Surface of mattress must be at least 5 inches below the upper edge of guardrails on top bunk.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
6. Periodically check and ensure that the guardrails, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact Restoration Hardware for replacement parts
10. Use of a night light may provide added safety precaution for a child using the upper bunk.
11. Use guardrails on both sides of the upper bunk.
12. If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed
should be placed against the wall to prevent entrapment between the bed and the wall.
13. The use of water flotation mattresses is prohibited.
14. STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are
not designed for use with the bed: for example, but not limited to, hooks, belts, and jump ropes.
15. Keep these instructions for future reference.
WARNING
Model No: 0288 - 12/ 13
KIERAN STUDY BUNK BED TWIN/ FULL

PARTS IDENTIFICATION
Page 3 of 11
(B) Footboard (x1 piece)
(A) Headboard (x1 piece)
(E) Shelf Panels (x4 pieces)
(C) Long Guard Rail (x1 piece) (D) Front Guard Rail (x1 piece)
(F) Support Bars (x4 pieces)
(G) Top Platform Panels (x2 pieces) (H) Ladder (x1 piece)
Model No: 0288 - 12/ 13
KIERAN STUDY BUNK BED TWIN/ FULL

Page 4 of 11
HARDWARE INCLUDED
TOOLS NEEDED
Phillips-head Screwdriver (not included)
ASSEMBLY INSTRUCTIONS
Note: - Bed must be assembled by at least two people.
- Please read instructions carefully before assembling bed.
- Use the parts and fittings list to identify each component.
- Keep all packing materials until assembly is complete to avoid loss of smaller parts.
- Do not completely tighten all bolts until all steps are finished.
1
2
3
4
5
6
7
8
9
10
3 pieces.
1 piece.
28 pieces.
Long Bolt 5/16”x2-1/2"
4 pieces.
4 pieces.
4 pieces.
48 pieces.
1 piece.
4 pieces.
Long Screw 8x30mm
Short Screw 7x15mm
2 pieces.
Middle Screw 8x19mm
Key Wrench 4mm
NO. ITEM DESCRIPTIONQTY.
Small Bolts 1/4” x 5/8“
Threaded Rod 5/16” x 2-1/2”
Curved Slotted Washer
5/16"x30x15x2 mm
Hex Nut
5/16"x 12 x 12 mm
12 mm Hex Wrench 12mm
Model No: 0288 - 12/ 13
KIERAN STUDY BUNK BED TWIN/ FULL

Page 5 of 11
STEP 2:
STEP 1:
E
A
B
A
B
Model No: 0288 - 12/ 13
KIERAN STUDY BUNK BED TWIN/ FULL
Lay the Shelf panels (E) into the Headboadr (A)
and the Footboard (B), ( as seen below).
Insert the Threaded Rods (4) into the Posts of
Headboard/ Footboard (A, B), (as seen below).
4
4
45mm

Page 6 of 11
STEP 3:
STEP 4:
C
D
4
Lay the Long Guard Rail (C), Front Guard Rail (D),
to the posts of the headboard / footboard
(as seen below).
Model No: 0288 - 12/ 13
KIERAN STUDY BUNK BED TWIN/ FULL
Attach the Shelf panels (E) to the
Headboadr (A) and the Footboard (B)
using (28 pcs.) Short Screws (9), and
tighten with Phillips-head screwdrive
(not included).
9 (x28 pcs.)

Page 7 of 11
STEP 5:
2
1
654
3
1
10
Attach the Long Guard Rail (C) and Front Guard
Rail (D) on top the posts of headboard/ footboard,
using Small Bolts (2) and tighten with Allen key (1).
STEP 6:
Insert Long Bolts (3) and tighten with Allen key (1).
Then, insert Curved Slotted Washers (5), and Hex
Nut (6) to Threaded Rod (4), and tighten with Hex
Wrench (10). (as seen below).
Model No: 0288 - 12/ 13
KIERAN STUDY BUNK BED TWIN/ FULL
CD

STEP 7:
Page 8 of 11
Position the Ladder (H) in the opening between
the Front Guard Rail (D) and Footboard (B).
Hook the Ladder (H) over the cross bar of Front
Guard Rail (D) and Right Leg of Footboard (B).
Insert the (2 pcs.) Middle Screws (8), and tighten
with Phillips-head screwdrive (not included).
8
H
B
HD
B
H
Model No: 0288 - 12/ 13
KIERAN STUDY BUNK BED TWIN/ FULL

STEP 9:
Page 9 of 11
STEP 8:
Lay the Support Bars (F) between the Long
Guard Rail (C) and Front Guard Rail (D), using
Long Screws (7) and tighten with Phillips -
head screwdriver (not included).
Phillips-head
screwdriver.
F
7
F
G
Lay the Top Platform Panels (G) on top of the
Support Bars (F) and attach using Qty.40 pcs
Long Screws (7) with Phillips-head screwdriver.
7 (x40 pcs.)
Model No: 0288 - 12/ 13
KIERAN STUDY BUNK BED TWIN/ FULL

Page 10 of 11
After the bunk bed is completely assembled,
return to each bolt and tighten to snug fit.
DO NOT over tighten.
WARNING:
Can be adjusted
by using Leveler.
Model No: 0288 - 12/ 13
KIERAN STUDY BUNK BED TWIN/ FULL

STEP 10: INSTALL BEDDING
UPPER BUNK MATTRESS DIAGRAM
MATTRESS
CARE INSTRUCTIONS
BEDDING SPECIFICATIONS FOR TOP BUNK:
The following size mattress and Foundation are specified for use with this Bunk bed:
MATTRESS DIMENSION SPECIFICATIONS FOR TOP BUNK
Twin - over - twin Bunk: (74" - 75") long x (37 1/2" - 38 1/2") wide x 6" thick
Full - over - full bunk: (74" - 75") long x (53 1/2" - 54 1/2") wide x 6" thick
PLATFORM :
-Twin - over - twin bunk: Upper bed consists of 2 pcs platform 37 3/4" long x 38 3/4" wide x 3/4" thick & bottom bed consists of
14 pcs slats 38 3/4" long x 2 1/2" wide x 3/4" thick.
-Full - over - full Bunk: Upper bed consists of 2 pcs platform 37 3/4" long x 53 7/8" wide x 3/4" thick & bottom bed consists of
14 pcs slats 53 7/8" long x 2 1/2" wide x 3/4" thick.
**Note: MATTRESS THICKNESS MUST NOT EXCEED MAX 6" FOR TOP BUNK.
Be sure to adhere to these BEDDING SPECIFICATIONS in order to avoid the possibility of falling or entrapment.
THESE SPECIFICATIONS MUST BE STRICTLY ADHERED TO !
Dust often using a clean, soft, dry lint-free cloth.
Blot spills immediately, and wipe with a clean, damp cloth.
We do not recommend the use of chemical cleansers, abrasives, or furniture polish on our lacquered finish.
5" MINIMUM DISTANCE
FROM TOP OF MATTRESS
TO TOP OF GUARD RAIL
6" MAXIMUM
THICKNESS
SIDE RAIL
PLATFORM
Page 11 of 11
Model No: 0288 - 12/ 13
KIERAN STUDY BUNK BED TWIN/ FULL