Rice Lake iDimension PWD User guide

iDimension® PWD
Static Dimensioning System
Setup Manual
PN 199543 Rev AJuly 21, 2020

An ISO 9001 registered company
© Rice Lake Weighing Systems. All rights reserved.
Rice Lake Weighing Systems® is a registered trademark of
Rice Lake Weighing Systems.
All other brand or product names within this publication are trademarks or
registered trademarks of their respective companies.
All information contained within this publication is, to the best of our knowledge, complete and
accurate at the time of publication. Rice Lake Weighing Systems reserves the right to make
changes to the technology, features, specifications and design of the equipment without notice.
The most current version of this publication, software, firmware and all other product
updates can be found on our website:
www.ricelake.com

Contents
© Rice Lake Weighing Systems ● All Rights Reserved i
Contents
Technical training seminars are available through Rice Lake Weighing Systems.
Course descriptions and dates can be viewed at www.ricelake.com/training
or obtained by calling 715-234-9171 and asking for the training department.
1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.4 Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.5 Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.6 Next Steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.0 Network Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 Service Port Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2 Admin Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.3 Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4 Edit/Cancel/Save Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.0 Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.1 General Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1.1 General Settings Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1.2 External Cameras Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.0 Measurement Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.1 Measurement Settings Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.2 Remote Sensors Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.3 Certification Settings Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.0 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.1 IFM Sensor Alignment and Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5.2 Setup Work Area. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.0 Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.1 Network Settings Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.2 Network Security Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

iDimension PWD Setup Manual
ii Visit our website www.RiceLake.com
Rice Lake continually offers web-based video training on a growing selection
of product-related topics at no cost. Visit www.ricelake.com/webinars

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 1
1.0 Introduction
This manual provides an overview on how to setup QubeVu Manager for the iDimension PWD.
Ensure the iDimension PWD unit is fully assembled by following the instructions of the iDimension PWD Assembly Instructions
(PN 198812).
When interfacing this device to a third party program, please reference the software manufacturer’s documentation for setup
and configuration parameters as necessary.
Manuals and additional resources are available from the Rice Lake Weighing Systems website at www.ricelake.com
Warranty information can be found on the website at www.ricelake.com/warranties
1.1 Additional Resources
For additional resources, see the following information:
iDimension PWD Assembly Instructions
The iDimension PWD Assembly Instructions (PN 198812) provides an overview on how to assemble the iDimension PWD.
iDimension PWD Operation Manual
The iDimension PWD Operation Manual (PN 198811) provides an overview on how to operate the iDimension PWD.
iDimension PWD Managers Guide
The iDimension PWD Managers Guide (198680) provides a detailed overview of the installation requirements, operation of the
iDimension PWD and configuration parameters to change in the QubeVu Manager to alter the performance of the unit.
The iDimension PWD Managers Guide is provided with each unit.
880 Performance™ Series Controller and Indicator Technical Manual
The 880 Performance Series Controller and Indicator Technical Manual (PN 158387) provides a detailed overview of the 880
indicator installation, configuration and operation procedures.
SUMMIT® 3000 Installation Manual
The SUMMIT 3000 Installation Manual (PN 76012) provides a detailed overview of the SUMMIT 3000 installation procedure.
1.2 Regulatory Information
This product is a Class 1 Laser Product according to IEC 60825-1:2007 Ed. 2.0 and complies with 21 CFR 1040.1 pursuant to
Laser Notice No. 50. A laser source with a diffraction optical element is embedded in the product, which produces a maximum
output power of 1.1 mW at the aperture with a maximum wavelength of 825 nm.
FCC
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at their own expense. Changes or modifications not expressly approved by Postea, Inc. could void the user’s FCC
granted authority to operate the equipment.

iDimension PWD Setup Manual
2 Visit our website www.RiceLake.com
1.3 Safety
Safety Signal Definitions:
Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. Includes
hazards that are exposed when guards are removed.
Indicates a potentially hazardous situation that, if not avoided, could result in serious injury or death. Includes
hazards that are exposed when guards are removed.
Indicates a potentially hazardous situation that, if not avoided, could result in minor or moderate injury.
Indicates information about procedures that, if not observed, could result in damage to equipment or corruption
to and loss of data.
General Safety
Do not operate or work on this equipment unless this manual has been read and all instructions are understood.
Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Rice Lake
Weighing Systems dealer for replacement manuals.
Failure to heed could result in serious injury or death.
Electric shock hazard!
For pluggable equipment the socket outlet must be installed near the equipment and must be easily accessible.
Always disconnect from main power before performing work on the device.
Do not allow minors (children) or inexperienced persons to operate this unit.
Do not operate without all shields and guards in place.
Do not place fingers into slots or possible pinch points.
Do not use this product if any of the components are cracked.
Do not make alterations or modifications to the unit.
Do not remove or obscure warning labels.
Do not use near water, avoid contact with excessive moisture.
Keep the unit dry.
Never use damaged power cords, plugs or loose electrical sockets.
Never touch the power cord with wet hands.
Mount on a flat surface.
Never use product for anything other than its intended purpose.
Follow OSHA regulations for installation and use of equipment.
DANGER
WARNING
CAUTION
IMPORTANT
WARNING

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 3
1.4 Installation Requirements
Avoid installation of the unit near direct sunlight. Direct sunlight and overhead lighting may cause void pixels
and noise that will affect the system from performing a dimension.
1.5 Site Preparation
Choose a location to meet the following requirements:
1. Forklift scale available for placement of frame and installation of floor scale.
2. Scissor lift or forklift for assembly of the stand.
3. 120 V power within 25'.
4. Network connection, if applicable with static IP address.
5. Flat concrete surface.
6. Minimum ceiling height of 130'' without any overhead obstruction.
7. Minimum floor space of 105'' depth and 84'' width for installation.
8. Indoor lighting only, direct sunlight may affect dimensioning performance.
9. For indoor use only, rated from 32°F–104°F (0°C–40°C).
10. Contact local scale dealer for installation and calibration of floor scale.
1.6 Next Steps
Additional setup requires connection of the iDimension PWD to a PC from a network connection to access QubeVu Manager.
1. Connect the iDimension PWD to the network (Section 2.0 on page 4).
2. Remote sensor calibration (Section 5.1 on page 22).
3. Alignment of IFM sensors to the center of the floor scale and calibration (Section 4.0 on page 14).
4. Default factory settings are preconfigured for the 880 indicator and the .bmp image type.
5. Work area and zone of Interest configuration (Section 5.0 on page 20).
6. Configure network (Section 6.0 on page 30).
IMPORTANT

iDimension PWD Setup Manual
4 Visit our website www.RiceLake.com
2.0 Network Connection
This section provides an overview of iDimension PWD network connections and configuration.
2.1 Service Port Connection
Configuring the iDimension PWD uses the embedded firmware, QubeVu Manager, which is accessed via an IP address over a
wired Ethernet connection through a web browser. The system default is set to Dynamic Control Host Protocol (DCHP).
To access QubeVu Manager, connect the iDimension PWD via ethernet to a computer then open a web browser and enter:
http://192.168.0.2, or 169.254.1.1 which are factory defaults.
Figure 2-1. QubeVu Manager Home Page
Parameter Description
Displays Display information (iDimension PWD Managers Guide (PN 198810))
Operator Tools Operator tools information (iDimension PWD Managers Guide (PN 198810))
Admin Tools Admin tools instructions (Section 2.2 on page 5)
License License information (iDimension PWD Managers Guide (PN 198810))
Table 2-1. QubeVu Manager Home Page Navigation

Network Connection
© Rice Lake Weighing Systems ● All Rights Reserved 5
2.2 Admin Tools
The Admin Tools menu is used for configuring, calibrating, defining, upgrading, backing up and running diagnostics on the system.
To enter the Admin Tools menu use the following procedure:
1. Press from the QubeVu Manager menu (Figure 2-1 on page 4) to enter the Admin Tools menu.
2. The QubeVu Manager login screen displays. The default username and password are admin and password.
Figure 2-2. Admin Tools Menu
Parameter Description
Setup General (optional and scale), time and date, data extraction and long term storage, measurement, network settings (Section 3.0 on page 8)
Calibration Calibration settings, define work area and calibrate cameras (Section 5.0 on page 20)
Capture Definitions Capture definitions for QubeVu (iDimension PWD Managers Guide (PN 198810))
Firmware Upgrade Update firmware (iDimension PWD Operation Manual (PN 198811))
Backup Backup and restore settings (Dimension PWD Managers Guide (PN 198810))
Diagnostics Diagnostics settings (iDimension PWD Operation Manual (PN 198811))
Table 2-2. Admin Tools

iDimension PWD Setup Manual
6 Visit our website www.RiceLake.com
2.3 Navigation
A navigation menu is located in the upper left section of all pages. This allows users to keep track of their current location and
provides links back to each preceding page.
Example: The user is in the Calibration Settings screen and can select Admin Tools to return to the Admin Tools
menu or Qubevu Manager to return to the home page.
Figure 2-3. Menu Navigation