Rice Lake VS-10 User manual

VS-10
Veterinary Scale
Operation Manual
September 8, 2023 PN 220913 Rev A

© Rice Lake Weighing Systems. All rights reserved.
Rice Lake Weighing Systems® is a registered trademark of
Rice Lake Weighing Systems.
All other brand or product names within this publication are trademarks or
registered trademarks of their respective companies.
All information contained within this publication is, to the best of our knowledge, complete and
accurate at the time of publication. Rice Lake Weighing Systems reserves the right to make
changes to the technology, features, specifications and design of the equipment without notice.
The most current version of this publication, software, firmware and all other product
updates can be found on our website:
www.ricelake.com

Revision History
© Rice Lake Weighing Systems ● All Rights Reserved 3
Technical training seminars are available through Rice Lake Weighing Systems.
Course descriptions and dates can be viewed at www.ricelake.com/training
or obtained by calling 715-234-9171 and asking for the training department.
Revision History
This section tracks and describes manual revisions for awareness of major updates.
Revision Date Description
A September 8, 2023 Established revision history
Table i. Revision Letter History

VS-10 Veterinary Scale
4 Visit our website www.RiceLake.com
Rice Lake continually offers web-based video training on a growing selection
of product-related topics at no cost. Visit www.ricelake.com/webinars
1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.0 Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.0 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1 Display Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2 Initial Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.3 Set Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.3.1 KG Units Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.3.2 LB/OZ Units Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.3.3 Unlock Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.4 Weigh With A Tare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.5 Weigh Without A Tare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.0 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.1 Basic Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.0 Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Contents

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 5
1.0 Introduction
The Rice Lake Veterinary Scale (VS-10) provides precise weighing of animals for accurate, reliable and repeatable
weighments. Movement compensation technology eliminates errors caused by spontaneous movement of the animal and the
weight can be displayed in pounds/ounces or in kilograms.
Manuals are available from Rice Lake Weighing Systems at www.ricelake.com/manuals
Warranty information is available at www.ricelake.com/warranties
Figure 1-1. VS-10 Digital Veterinary Scale
1.1 Safety
Safety Definitions:
DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. Includes
hazards that are exposed when guards are removed.
WARNING: Indicates a potentially hazardous situation that, if not avoided, could result in serious injury or death. Includes
hazards that are exposed when guards are removed.
CAUTION: Indicates a potentially hazardous situation that, if not avoided, could result in minor or moderate injury.
IMPORTANT: Indicates information about procedures that, if not observed, could result in damage to equipment or
corruption to and loss of data.
General Safety
Do not operate or work on this equipment unless this manual has been read and all instructions are understood.
Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Rice Lake
Weighing Systems dealer for replacement manuals.
WARNING
Failure to heed could result in serious injury or death.
Ensure every individual operating or working with this unit has read and understands the following safety information.
Do not transport the scale with an animal on the weighing tray.
Clean the scale regularly to avoid cross contamination.
Do not allow minors (children) or inexperienced persons to operate this scale.
Do not use in the presence of flammable materials.
Do not use this product if any of the components are loose or cracked.
Do not drop the scale or subject it to violent shocks.
For accurate weighing, the scale must be placed on a level, stable surface.
Weight exceeding the maximum rated scale capacity may damage the scale.
Avoid contact with excessive moisture.
Do not make alterations or modifications to the scale; any alterations void the warranty.
For accurate weighing, verify proper setup is complete prior to first use. See Section 3.2 on page 8.
Operation at voltages and frequencies other than specified could damage the scale.
Utilizing adapters not supplied by Rice Lake Weighing Systems voids all warranties.
i

VS-10 Veterinary Scale
6 Visit our website www.RiceLake.com
2.0 Setup
The VS-10 comes fully assembled and includes the scale and a 120 V adapter. Immediately after unpacking, visually inspect
the VS-10 to ensure all components are included and undamaged. If parts were damaged in shipment, notify Rice Lake
Weighing Systems and the shipper immediately.
Use the following instructions for scale setup:
1. Place the scale on a sturdy, level surface.
2. Connect the 120 V adapter to the back of the scale.
3. Plug the AC adapter into a power source.
Figure 2-1. AC Power Connection Site
The VS-10 can also be powered by four AA alkaline batteries if an additional power source is not available. A battery powered
scale automatically turns off after two minutes of not being used to save battery life. Replace the batteries or connect to an AC
power source as soon as possible if the low battery indicator (Lo) displays.
Figure 2-2. Low Battery Indicator
AC Power Connection
120 V Adapter

Operation
© Rice Lake Weighing Systems ● All Rights Reserved 7
3.0 Operation
The VS-10 accurately weighs small animals up to 44 lb (20 kg). The weighing surface also includes a ruler for measuring the
length of the animal. The built-in ruler can measure small animals up to 22.5 in (57 cm).
NOTE: If the scale is battery powered and has not been used for two minutes, it automatically turns off to save battery life.
3.1 Display Descriptions
The following section describes the VS-10 operating keys and their functions.
Figure 3-1. VS-10 Display
NOTE: The VS-10 comes pre-calibrated from the factory.
Item Description Function
1 Motion annunciator Displays when a weight reading is complete
2 Negative/Minus annunciator Indicates a negative weight reading
3 Zero annunciator Indicates the scale is stable and ready for use
4 Memory annunciator Indicates the last weight measurement is displayed after pressing RECALL
5 6-Digit LCD digital display Displays the weight in pounds/ounces or kilograms
6 On/Off Press to turn On
Press and hold to turn Off
Tare With weight on the scale, short press to tare off the weight, 0 displays
7 LB/KG Selects pounds/ounces or kilograms
8 RECALL Recalls the last weight measurement
Example: Weigh a an animal on the scale and then remove the animal
Press RECALL and the animal’s weight displays again
9 LB/OZ annunciator Indicates the scale is weighing in pounds/ounces
KG annunciator Indicates the scale is weighing in kilograms
Table 3-1. Front Panel with Annunciators Displayed
ON/TARE
LB/KG
RECALL
zero mem lb oz
1
2
34
6
7
8
5
9

VS-10 Veterinary Scale
8 Visit our website www.RiceLake.com
3.2 Initial Setup
Use the following steps to set up and verify the VS-10 upon initial power up and periodically thereafter.
1. Plug AC adapter cable into the back of the scale (Figure 2-1 on page 6) and the AC adapter plug into a power source.
2. Turn on the scale. A self test runs and 0.00.0 lb or 0.00 kg displays when complete.
3. Place a weight, not exceeding 40 lb, on the scale. The weight measurement is complete when Ο displays.
4. Press to select unit of measure, lb/oz or kg.
5. Remove the weight from the scale. To display the weight again, press .
NOTE: If setup procedure fails, see Section 4.3 on page 10. If the problem is not resolved, refer to a qualified service
provider.
3.3 Set Units
The VS-10 can be set to display weights in lb/oz only, kg only, or to toggle between lb/oz and kg units on the scale.
3.3.1 KG Units Only
Lock the weight units to display in kg only.
1. Ensure the scale is turned on.
2. Press to change the displayed units to kg.
3. Press and hold for five seconds until kg flashes.
4. Release . The weight units are now locked in kg. Pressing does not switch units to lb/oz.
3.3.2 LB/OZ Units Only
Lock the weight units to display in lb/oz only.
1. Ensure the scale is turned on.
2. Press to change the displayed units to lb/oz.
3. Press and hold for five seconds until lb oz flashes.
4. Release . The weight units are locked in lb/oz. Pressing does not switch units to kg.
3.3.3 Unlock Units
Unlock the weight units to toggle between lb/oz and kg.
1. Ensure the scale is turned on.
2. Press and hold for five seconds until kg or lb oz flashes.
3. Release . Pressing toggles units between lb/oz and kg.
LB/KG
RECALL
LB/KG
LB/KG
LB/KG
LB/KG
LB/KG
LB/KG
LB/KG
LB/KG
LB/KG
LB/KG
LB/KG

Operation
© Rice Lake Weighing Systems ● All Rights Reserved 9
3.4 Weigh With A Tare
The tare function removes the weight of additional items on the scale, such as a collar or pad, at the time the animal is weighed.
1. Turn on the scale. 0:0.0 lb oz or 0.00 kg displays.
2. Place a collar on the weighing tray, ensuring the edges of the collar are not touching the stand. Ο displays when the
weight reading is complete.
3. Press to remove the weight of the pad or any other accessory on the weighing tray.
4. Place an animal on the scale. Ο displays when the weight reading is complete.
5. Remove the animal from the scale.
6. Press to display the weight again, if necessary.
3.5 Weigh Without A Tare
Use this procedure when there are no additional items on the scale at the time the animal is weighed.
1. Turn on the scale. 0:0.0 lb oz or 0.00 kg displays.
2. Place an animal on the scale. Ο displays when the weight reading is complete.
3. Remove the animal from the scale.
4. Press to display the weight again, if necessary.
ON/TARE
RECALL
RECALL

VS-10 Veterinary Scale
10 Visit our website www.RiceLake.com
4.0 Maintenance
The following section provides instructions for maintaining, cleaning and troubleshooting the VS-10.
IMPORTANT: Maintenance operations not described in this section must be performed by qualified service personnel.
4.1 Basic Maintenance
• Check the scale for proper operation and function before first use and after periods of non-use.
• Inspect the scale. If the scale does not operate correctly, contact qualified service personnel.
• Check the overall appearance of the entire scale for any obvious signs of damage.
• Inspect the condition of the AC adapter for cord fraying or for broken or bent prongs.
4.2 Cleaning
Proper care and cleaning is essential to ensure a long life of accurate and effective operation. Disconnect the scale from the AC
power source before beginning the cleaning process.
IMPORTANT: Do not immerse the scale into cleaning solutions or other liquids. Do not use Isopropyl alcohol or other
solutions to clean the display surface.
1. Clean all external surfaces with a clean, damp cloth or tissue. Mild soap and water solution can be used.
2. Dry with a clean, soft cloth.
4.3 Troubleshooting
Use the following instructions to troubleshoot any errors with the scale.
Symptom Possible Cause Corrective Action
Scale does not turn on Batteries are dead Replace batteries or connect scale to a power source
Electrical outlet is faulty Use a different electrical outlet
Power supply is faulty Replace the adapter
NOTE: Utilizing adapters not supplied by Rice Lake
Weighing Systems voids all warranties
Scale displays questionable weight or
does not zero
There is weight on or an object interfering with the scale Remove animal, weight or interfering object from scale
Weight was placed on the scale before 0.0 displayed Remove animal, or weight from the scale; zero scale
and begin weighing process again
Scale is not on a level surface Place scale on a stable surface and begin weighing
process again
Weighing tray is not placed properly Ensure weighing tray is properly installed
Scale is out of calibration Check scale calibration with a known weight value;
contact a qualified service provider to perform a new
calibration if the calibration is incorrect
o_Ld message is displayed Load on the scale exceeds the capacity Remove excess weight and use scale according to its
stated limit
Err message is displayed RECALL key was pressed with insufficient weight on
the scale
Place more than 2 lb 30 oz on the scale
Table 4-1. Troubleshooting Table