Richmond GTR055 User manual

GTR055 Electric Lock Manual Rev 1 1
Wired Keypad to Suit
Automatic Gate Kits
GTR055
Suits the Following Richmond Gate Motors:
GTR058, GTR062, GTR078, GTR099, GTR064, GTR156, GTR207
Optional gooseneck
post to suit available
Part Number: GTR056

GTR055 Electric Lock Manual Rev 1 2
Part B: Connection with Swing Gate Openers
Part A: Denition of the Flat Cable

GTR055 Electric Lock Manual Rev 1 3
How to set the keypad to programming (settings) mode:
When the keypad is in standby mode,
Step 1: Press the " #" button four (4) times until the red LED is OFF and the green LED is ON.
Step 2: Enter the program password (the default is 123456) and then press and release the " #" button.
The Green LED will ash which indicates the keypad is in program mode.
If you have failed, the Red LED will be ON and the green LED will be OFF please try it again.
How to change the programming (settings) password:
When the keypad is in programming mode,
Step 1: Press the " 0" button.
Step 2: Enter your new 6 digit password and then press and release the " # " button.
Step 3: Repeat step 2 to conrm the change. The keypad will return to programming mode after
the change. Press and release the "*" button to return to standby mode if you do not want to
make any other changes.
Part C: Programming the Keypad
• There are three kinds of passwords for programming:
"program password", "entry password", and "card password".
• All passwords are six (6) digits in length.
• "Program password" is used to set the kepad into programming(settings) mode
• "Entry password" is used to activate the relay of the keypad when it has been set to "password" or
:password or card" mode.
• The factory default program password is 123456
• The factory default card password is 888888

GTR055 Electric Lock Manual Rev 1 4
How to change access mode:
When the keypad is in programming mode, you can:
1. Enter "4", "0", "#" to set the keypad to Card or Password Mode (default value) or
2. Enter "4", "1", "#" to set the keypad to Card + Password Mode or
3. Enter "4", "2", "#" to set the keypad to Password Mode
The keypad will return to programming mode after setting. Press and release the " *" nutton to return the
keypad to standby mode if you don't want to make any other changes.
How to change the duration of the Dry Contact Output:
When the keypad is in programming mode,
Step 1: Press and release the "5" button.
Step 2: Enter 2 digits delay time (Unit: second). and then press and release the "#" button to conrm it.
The keypad will return to programming mode after setting. Press and release the " *"button to return to
standby mode if you do not want to make any other changes.
NOTE: Factory default setting is 3 seconds. If the time has been set to 99, you have to enter the
password again to restore the Dry contact Output.
How to set & change the entry password (no matter the old password):
When the keypad is in programming mode,
Step 1: Press and release the "6" button.
Step 2: Enter your new 6 digit entry password and the press and release the "#" button.
Step 3: Repeat step 2 to conrm the change. The keypad will return to programming mode after the change.
Press and release the "*" button to return to standby mode if you do not want to make any other changes.
NOTE: Factory default entry password is blank. You can press "6" "# " "#" to deactivate the entry
password.

GTR055 Electric Lock Manual Rev 1 5
How to reset the programming password to the default value (123456):
Open the back cover of the wired keypad, you'll nd a jumper on the PCB. Change the jumper to 2-3 position
and then power on the keypad. After two short beeps, put the jumper back to the 1-2 position, the program
password has been reset to factory default value (123456)
NOTE: No card will be deleted after reset. The entry password and the card password could not be
changed after reset.
How to use the keypad to operate the gate opener:
If the keypad has been set to "Card Or Password" mode, when the keypad is in standby mode, you can,
1. Enter the 6 digit entry password and then press the "#" button to operate the gate opener OR
2. Swipe the card which has been learnt by the keypad to operate the gate opener
If the keypad has been set to "Card + Password" mode, when the keypad is in standby mode, you can
swipe the card and then enter 6 digits card password, lastly press and release the "#" button to operate
the gate opener.
If the keypad has been set to "Password" mode, when the keypad is in standby mode, you can enter the
6 digit entry password and then press and release the "#" button to operate the gate opener.

GTR055 Electric Lock Manual Rev 1 6
Part D: Examples
1.How to change program password to 110120 (from default)
Step 1: Press the "#" button four (4) times until the red LED is OFF and the green LED is ON.
Step 2: Enter "1 2 3 4 5 6" and then press and release the "#" button. The green LED will ash which
indicates that the keypad is in programming mode.
Step 3: Press and release the "0" button.
Step 4: Enter "1 1 0 1 2 0" and then press and release the "#" button.
Step 5: Repeat step 4 to conrm the change.
Step 6: Press and release the "*" button to return to standby mode
2. How to change entry password to "332662" from any old password
Step 1: Press the "#" button four (4) times until red LED is OFF and green LED is ON.
Step 2: Enter "1 2 3 4 5 6" and then press and release the "#" button. The green LED will ash which
indicates that the keypad is in programming mode.
Step 3: Press and release the "6" button.
Step 4: Enter "3 3 2 6 6 2" and then press and release the "#" button.
Step 5: Repeat step 4 to conrm the change.
Step 6: Press and release the "*" button to return to standby mode.

GTR055 Electric Lock Manual Rev 1 7
Part E: Keying Indication Summary