RIEJU KOSO User manual

Familiarising yourself with the moped
Chassis
EN
G
LI
S
H
INSTRUMENT PANEL
1-
2-
3-
4-
Turn indicators indicator light
This indicator light flashes when the turn indicator switch is moved to the left or to
the right.
Oil temperature indicator light
This indicator light comes on when the oil temperature is too high.
“N” neutral indicator light
This indicator light comes on when the transmission is in the neutral position.
Main beam indicator light.
This indicator light comes on when the headlight is on main beam.
F-9
KOSO 1
2
3
4

Electrical system
Chassis
ENGLI
S
H
SENSORS
Checking the functioning of the indicator lights.
Temperature and oil indicator:
Checking these requires making a bridge to earth with each cable corresponding to the
graphic for the instrument panel.
Turn indicators indicator:
To check the turn indicators indicator light, connect the green cable to earth and the
brown to positive.
Main beam indicator:
Connect the indicator’s yellow /white cable to the magneto’s yellow AC cable.
Neutral sensor
To check this sensor, the circuit should be checked between the terminal and earth.
With the gearbox in neutral, it should register 0Ω
On selecting a gear the meter should register ∞(Infinito)
DIAGRAM OF THE KOSO INSTRUMENT PANEL

Electrical system
Chassis
ENGLI
S
H
Instructions for use
PRESS
PRESS THE BUTTON DOWN FOR THREE SECONDS
PROGRAMMING KOSO INSTUMENT PANEL
N.B.:
The notes contain detailed information about the installation.
( ) Processes to be followed is obligatorily to avoid the problems caused by an incorrect
installation.
Indicators
Neutral light (green)
Main beam light (blue)
Turn indicators light (green)
Oil temperature (red) ( )
Speedometer
Interval: 0-360 km/h (0-223 MPH).
Unit of measurement: km/h or MPH.
Thermometer level indicator
Interval: 20-120 °C (68-248 °F) in 5 levels.
Unit of measurement: one level is equivalent to some 10 °C (50 °F).
Adjustment button Selection button
Oil temperature warning
When the temperature is higher
than 120 °C (248 °F)
Odometer
• Interval: 0-99,999 km (miles); automatic restart after 99,999 km (miles).
• Unit of measurement: 1 km (mile).
Trip meter
• Interval: 0-999,9 km (miles); automatic restart after 999.9 km (miles).
• Unit of measurement: 0.1 km (miles).
Adjustment button
• On the main screen, press the adjustment button to change the odometer and the trip meter.
• On the trip meter screen, press the adjustment button for 3 seconds to reset the trip meter
to zero.

ENGLISH
Electrical system
Chassis
On the main screen, hold down the selection
and adjustment buttons for 3 seconds to
access the adjustment of the speed measure-
ment unit.
Press the adjustment button to select the
unit of measurement.
E.g.: Now the setting is km/h.
Now the speed measurement unit is flashing.
N.B.: On the adjustment screen for the speed
measurement unit, the user can choose bet-
ween km/h or MPH.
The odometer and the trip meter change along
with the speed measurement unit.
Press the selection button to continue adjus-
ting the function.
N.B.: When this screen is exited, the adjust-
ment defined will begin to be applied.
If adjustment of this function alone is required,
hold down the selection button for three se-
conds to go back to the main screen.
On the main screen, hold down the selection
and adjustment buttons for 3 seconds to
access the adjustment of the speed measure-
ment unit.
Adjustment of the speed measurement unit.
Tyre circumference and adjustment of the sensor points (to change to a
different tyre size).

Electrical system
Chassis
ENGLI
S
H
Press the selection button to access the tyre
circumference adjustment.
E.g.: The tyre circumference is 1,300 mm.
Press the selection button to change to the
digit to be adjusted. E.g.: The original adjust-
ment is 1,000mm.
The 1 flashes.
N.B.: Tyre circumference adjustment interval:
300~2,500 mm; the digits are adjusted from
left to right.
Test it ! The valve can be taken as a starting point and
end point for measuring the circumference of the wheel
with a tape measure.
Press the adjustment button to change the ad-
justment.
The 0 flashes.
Press the selection button 3 times to change to
adjustment of the sensor points.
E.g.: The circumference of the tyre has been
changed from 1,000 mm to 1,300 mm.

ENGLISH
Electrical system
Chassis
E.g.: the sensor point to be adjusted is 6. Press
the selection button to change to the digit to be
adjusted. E.g.: the original setting is 1 point.
The 0 flashes.
N.B.: Sensor point adjustment interval: 1~60
points. The setting can be changed from left to
right.
N.B.: It is possible to adjust the sensor points
higher than 6 is possible only if the active speed
sensor is being used.
Press the adjustment button to select the set-
ting number.
The sensor points setting number flashes.
Press the selection button to continue adjus-
ting the functions.
E.g.: The adjustment of the sensor points of has
changed from 1 to 6.
N.B.: When this screen is exited, the adjust-
ment defined will begin to be applied.
If adjustment of this function alone is required,
hold down the selection button for three se-
conds to go back to the main screen.
Test it ! The active speed sensor can be fitted next to metal parts such as the brake
disk bolts to detect the distance of the disk and the sprocket holder in order to detect
the frequency of the gear teeth. We recommend using the method of detecting the disk
bolt as a signal for the speed. The more signals there are, the more precise the speed
reading. Please note that the maximum signal that the active speed sensor can read is
60 points per lap.

Electrical system
Chassis
ENGLI
S
H
KOSO WIRING DIAGRAM