Rigol DS8000-R Series User manual

User Guide
DS8000-R Series Digital
Oscilloscope
Nov. 2020
RIGOL TECHNOLOGIES CO., LTD.

RIGOL
DS8000-R User Guide I
Guaranty and Declaration
Copyright
© 2020 RIGOL TECHNOLOGIES CO., LTD. All Rights Reserved.
Trademark Information
RIGOL®is the trademark of RIGOL TECHNOLOGIES CO., LTD.
Publication Number
UGA27101-1110
Software Version
00.01.01.00.00
Software upgrade might change or add product features. Please acquire the latest
version of the manual from RIGOL website or contact RIGOL to upgrade the
software.
Notices
⚫RIGOL products are covered by P.R.C. and foreign patents, issued and pending.
⚫RIGOL reserves the right to modify or change parts of or all the specifications
and pricing policies at the company’s sole decision.
⚫Information in this publication replaces all previously released materials.
⚫Information in this publication is subject to change without notice.
⚫RIGOL shall not be liable for either incidental or consequential losses in
connection with the furnishing, use, or performance of this manual, as well as
any information contained.
⚫Any part of this document is forbidden to be copied, photocopied, or rearranged
without prior written approval of RIGOL.
Product Certification
RIGOL guarantees that this product conforms to the national and industrial
standards in China as well as the ISO9001:2015 standard and the ISO14001:2015
standard. Other international standard conformance certifications are in progress.
Contact Us
If you have any problem or requirement when using our products or this manual,
please contact RIGOL.
E-mail: servi[email protected]m
Website: www.rigol.com

RIGOL
II DS8000-R User Guide
Safety Requirement
General Safety Summary
Please review the following safety precautions carefully before putting the
instrument into operation so as to avoid any personal injury or damage to the
instrument and any product connected to it. To prevent potential hazards, please
follow the instructions specified in this manual to use the instrument properly.
Use Proper Power Cord.
Only the exclusive power cord designed for the instrument and authorized for use
within the local country could be used.
Ground the Instrument.
The instrument is grounded through the Protective Earth lead of the power cord. To
avoid electric shock, connect the earth terminal of the power cord to the Protective
Earth terminal before connecting any input or output terminals.
Connect the Probe Correctly.
If a probe is used, the probe ground lead must be connected to earth ground. Do not
connect the ground lead to high voltage. Improper way of connection could result in
dangerous voltages being present on the connectors, controls or other surfaces of
the oscilloscope and probes, which will cause potential hazards for operators.
Observe All Terminal Ratings.
To avoid fire or shock hazard, observe all ratings and markers on the instrument and
check your manual for more information about ratings before connecting the
instrument.
Use Proper Overvoltage Protection.
Ensure that no overvoltage (such as that caused by a bolt of lightning) can reach the
product. Otherwise, the operator might be exposed to the danger of an electric
shock.
Do Not Operate Without Covers.
Do not operate the instrument with covers or panels removed.
Do Not Insert Objects into the Air Outlet.
Do not insert anything into the holes of the fan to avoid damaging the instrument.
Use Proper Fuse.
Please use the specified fuses.

RIGOL
DS8000-R User Guide III
Avoid Circuit or Wire Exposure.
Do not touch exposed junctions and components when the unit is powered on.
Do Not Operate with Suspected Failures.
If you suspect that any damage may occur to the instrument, have it inspected by
RIGOL authorized personnel before further operations. Any maintenance,
adjustment or replacement especially to circuits or accessories must be performed
by RIGOL authorized personnel.
Provide Adequate Ventilation.
Inadequate ventilation may cause an increase of temperature in the instrument,
which would cause damage to the instrument. So please keep the instrument well
ventilated and inspect the air outlet and the fan regularly.
Do Not Operate in Wet Conditions.
To avoid short circuit inside the instrument or electric shock, never operate the
instrument in a humid environment.
Do Not Operate in an Explosive Atmosphere.
To avoid personal injuries or damage to the instrument, never operate the
instrument in an explosive atmosphere.
Keep Product Surfaces Clean and Dry.
To avoid dust or moisture from affecting the performance of the instrument, keep the
surfaces of the instrument clean and dry.
Prevent Electrostatic Impact.
Operate the instrument in an electrostatic discharge protective environment to avoid
damage induced by static discharges. Always ground both the internal and external
conductors of cables to release static before making connections.
Use the Battery Properly.
Do not expose the battery (if available) to high temperature or fire. Keep it out of the
reach of children. Improper change of a battery (lithium battery) may cause an
explosion. Use the RIGOL specified battery only.
Handle with Caution.
Please handle with care during transportation to avoid damage to keys, interfaces,
and other parts on the panels.

RIGOL
IV DS8000-R User Guide
Safety Notices and Symbols
Safety Notices in this Manual:
WARNING
Indicates a potentially hazardous situation or practice which, if not
avoided, will result in serious injury or death.
CAUTION
Indicates a potentially hazardous situation or practice which, if not
avoided, could result in damage to the product or loss of important data.
Safety Terms on the Product:
DANGER
It calls attention to an operation, if not correctly performed, could
result in injury or hazard immediately.
WARNING
It calls attention to an operation, if not correctly performed, could
result in potential injury or hazard.
CAUTION
It calls attention to an operation, if not correctly performed, could
result in damage to the product or other devices connected to the
product.
Safety Symbols on the Product:
Hazardous
Voltage
Safety Warning
Protective Earth
Terminal
Chassis Ground
Test Ground

RIGOL
DS8000-R User Guide V
Measurement Category
Measurement Category
DS8000-R series digital oscilloscopes can make measurements in Measurement
Category I.
WARNING
This oscilloscope can only be used for measurements within its specified
measurement categories.
Measurement Category Definitions
Measurement category I is for measurements performed on circuits not directly
connected to MAINS. Examples are measurements on circuits not derived from
MAINS, and specially protected (internal) MAINS derived circuits. In the latter case,
transient stresses are variable. Thus, you must know the transient withstand
capability of the equipment.
Measurement category II is for measurements performed on circuits directly
connected to low voltage installation. Examples are measurements on household
appliances, portable tools and similar equipment.
Measurement category III is for measurements performed in the building installation.
Examples are measurements on distribution boards, circuit-breakers, wiring
(including cables, bus-bars, junction boxes, switches and socket-outlets) in the fixed
installation, and equipment for industrial use and some other equipment. For
example, stationary motors with permanent connection to a fixed installation.
Measurement category IV is for measurements performed at the source of a
low-voltage installation. Examples are electricity meters and measurements on
primary overcurrent protection devices and ripple control units.
Ventilation Requirement
This oscilloscope uses a fan to force cooling. Please make sure that the air intake and
exhaust areas are free from obstructions and have free air. When using the
oscilloscope in a bench-top, allow at least 30 cm clearance from both sides of the
instruments; when using it in rack setting, keep at least 1 m clearance from the
surroundings of the cabinet. When running in the cabinet, keep it run in the room
temperature below 30°C.
WARNING
Inadequate ventilation may cause an increase of temperature in the
instrument, which would cause damage to the instrument. So please
keep the instrument well ventilated and inspect the air outlet and the fan
regularly.

RIGOL
VI DS8000-R User Guide
Working Environment
Temperature
Operating: -40℃to +50℃(for a single instrument)
-40℃to +30℃(for instruments in the cabinet)
Non-operating: -50℃to +70℃
Humidity
Operating:
Below +30℃: ≤90%RH (without condensation)
+30℃to +40℃: ≤75%RH (without condensation)
+40℃to +50℃: ≤45%RH (without condensation)
Non-operating:
Below 65℃: ≤90% RH (without condensation)
WARNING
To avoid short circuit inside the instrument or electric shock, never
operate the instrument in a humid environment.
Altitude
Operating: below 3 km
Non-operating: below 15 km
Installation (Overvoltage) Category
This product is powered by mains conforming to installation (overvoltage) category
II.
WARNING
Ensure that no overvoltage (such as that caused by a bolt of lightning)
can reach the product. Otherwise, the operator might be exposed to the
danger of an electric shock.
Installation (Overvoltage) Category Definitions
Installation (overvoltage) category I refers to signal level which is applicable to
equipment measurement terminals connected to the source circuit. Among these
terminals, precautions are done to limit the transient voltage to a low level.
Installation (overvoltage) category II refers to the local power distribution level
which is applicable to equipment connected to the AC line (AC power).
Pollution Degree
Pollution Degree 2

RIGOL
DS8000-R User Guide VII
Pollution Degree Definition
Pollution Degree 1: No pollution or only dry, nonconductive pollution occurs. The
pollution has no effect. For example, a clean room or air-conditioned office
environment.
Pollution Degree 2: Normally only nonconductive pollution occurs. Temporary
conductivity caused by condensation is to be expected. For example, indoor
environment.
Pollution Degree 3: Conductive pollution or dry nonconductive pollution that
becomes conductive due to condensation occurs. To be found in industrial
environment or construction sites (harsh environments). For example, sheltered
outdoor environment.
Pollution Degree 4: The pollution generates persistent conductivity caused by
conductive dust, rain, or snow.
For example, outdoor areas.
Safety Class
Class 1 –Grounded Product
Care and Cleaning
Care
Do not store or leave the instrument where it may be exposed to direct sunlight for
long periods of time.
Cleaning
Clean the instrument regularly according to its operating conditions.
1. Disconnect the instrument from all power sources.
2. Clean the external surfaces of the instrument with a soft cloth dampened with
mild detergent or water. Avoid having any water or other objects into the chassis
via the heat dissipation hole. When cleaning the LCD, take care to avoid
scarifying it.
CAUTION
To avoid damage to the instrument, do not expose it to caustic liquids.
WARNING
To avoid short-circuit resulting from moisture or personal injuries, ensure
that the instrument is completely dry before connecting it to the power
supply.

RIGOL
VIII DS8000-R User Guide
Environmental Considerations
The following symbol indicates that this product complies with the WEEE Directive
2002/96/EC.
Product End-of-Life Handling
The equipment may contain substances that could be harmful to the environment or
human health. To avoid the release of such substances into the environment and
avoid harm to human health, we recommend you to recycle this product
appropriately to ensure that most materials are reused or recycled properly. Please
contact your local authorities for disposal or recycling information.
You can click on the following link https://int.rigol.com/services/declaration.html to
download the latest version of the RoHS&WEEE certification file.

RIGOL
DS8000-R User Guide IX
DS8000-R Series Overview
DS8000-R series is a medium and high-end digital oscilloscope with a compact size
designed on the basis of the ASIC chip (RIGOL self-owns its intellectual property
right) and UltraVision II technical platform developed by RIGOL. It is compact and
thin in design. It supports system integration of multiple devices, rack mount
installation, and remote system operation to meet the system requirements for
industrial automation test system. DS8000-R series oscilloscope has an analog
bandwidth of up to 2 GHz, supporting multi-device synchronous triggering, available
to be extended to 512 channels. It provides an excellent solution for users to meet
their middle and high-speed requirement for the system integration test and
synchronization requirement for multi-channel data acquisition.
Main Features:
⚫Analog channel bandwidth: 350 MHz, 1 GHz, and 2 GHz
⚫Up to 10 GSa/s real-time sample rate (for DS8104-R/DS8204-R), 5 GSa/s (for
DS8034-R)
⚫4 analog channels, 1 EXT input channel
⚫Standard memory depth up to 500 Mpts
⚫High waveform capture rate (over 600,000 wfm/s)
⚫Low jitter, multiple-device synchronization (<200 psRMS, typical)
⚫High-speed data communication interface (10 GE SFP+), ensuring the reliable
transmission of massive data
⚫Integrates 6 independent instruments into 1, including digital oscilloscope,
spectrum analyzer, AWG (option), digital voltmeter, 6-digit counter and totalizer,
and protocol analyzer (option)
⚫Available to be extended to 512 channels, supporting synchronous acquisition
(with the multi-channel synchronization module)
⚫Real-time eye diagram and jitter analysis software (option for
DS8104-R/DS8204-R, but unavailable for DS8034-R)
⚫Built-in advanced power analysis software (option)
⚫Operating temperature low below -40℃, available to be used for signal
monitoring in some special conditions
⚫Multiple interfaces available: USB HOST&DEVICE, LAN(LXI), 10 GE SFP+, HDMI,
TRIG OUT, 10 MHz In, and 10 MHz Out
⚫Web Control remote command
⚫Compact and thin design, save rack space, 1U rack mount kit (standard)
⚫Software development kit available for users to meet their customized
development according to their specific scenarios
⚫Easy-to-use on-site multi-channel synchronization calibration kit, enabling you
to view multiple channels synchronously

RIGOL
XDS8000-R User Guide
Document Overview
Main Topics of this Manual:
Chapter 1 Quick Start
Introduces the preparations before using the oscilloscope and provides a basic
introduction of the instrument.
Chapter 2 To Set the Vertical System
Introduces the vertical system functions of the oscilloscope.
Chapter 3 To Set the Horizontal System
Introduces the horizontal system functions of the oscilloscope.
Chapter 4 To Set the Sample System
Introduces the sample system functions of the oscilloscope.
Chapter 5 To Trigger the Oscilloscope
Introduces the trigger mode, trigger coupling, trigger holdoff, external trigger, and
various trigger types of the oscilloscope.
Chapter 6 Operations and Measurements
Introduces how to make math operation, auto measurement, and cursor
measurement.
Chapter 7 Digital Voltmeter (DVM) and Frequency Counter
Introduces how to use the digital voltmeter and the frequency counter.
Chapter 8 Power Analysis (Option)
Introduces the power analysis function, analyzes the power quality and output ripple
noise of the input power.
Chapter 9 Histogram Analysis
Introduces the histogram analysis function.
Chapter 10 Real-time Eye Diagram and Jitter Analysis (Option)
Introduces the real-time eye diagram and jitter analysis function.
Chapter 11 Protocol Decoding
Introduces how to decode the input signal by using those common protocols.
Chapter 12 Reference Waveform
Introduces how to compare the input waveform with the reference waveform.

RIGOL
DS8000-R User Guide XI
Chapter 13 Pass/Fail Test
Introduces how to monitor the input signal by using the Pass/Fail test.
Chapter 14 Waveform Recording & Playing
Introduces the waveform recording & playing function.
Chapter 15 Search and Navigation Function
Introduces the navigation function and how to quickly search the relevant events.
Chapter 16 Display Control
Introduces how to control the display of the oscilloscope.
Chapter 17 Function/Arbitrary Waveform Generator (Option)
Introduces how to use the built-in Function/Arbitrary Waveform Generator option.
Chapter 18 Store and Load
Introduces how to store and load; how to carry out disk management.
Chapter 19 System Utility Function Setting
Introduces how to set the remote interfaces and system-related functions.
Chapter 20 Remote Control
Introduces how to control the oscilloscope remotely.
Chapter 21 Troubleshooting
Introduces how to deal with the common failures of the oscilloscope.
Chapter 22 Appendix
Provides the basic information for the options and accessories.

RIGOL
XII DS8000-R User Guide
Format Conventions in this Manual:
1. Key
The key on the front panel is denoted by the format of "Key Name (Bold) + Text
Box" in the manual. For example, RUN/STOP denotes the "RUN/STOP" key.
2. Menu
The menu items are denoted by the format of "Menu Word (Bold) + Character
Shading". For example, System denotes the "System" menu item under
"Utility" function.
3. Operation Procedures
→denotes the next step of operation. For example, Utility →System denotes
clicking on the navigation function icon to enter the "Utility" menu first, and then
clicking the System menu item.
4. Connector
The connectors on the front or rear panel are usually denoted by the format of
"Connector Name (Bold) + Square Brackets (Bold)". For example, [TRIG OUT].
Content Conventions in this Manual:
DS8000-R series includes the following models. Unless otherwise specified, this
manual takes DS8204-R as an example to illustrate the functions and operation
methods of DS8000-R series digital oscilloscope.
Model
Analog
Bandwidth
No. of
Analog
Channels
No. of Function/Arbitrary
Waveform Generator
Channels
DS8104-R
1 GHz
4
1, Opt
DS8204-R
2 GHz
4
1, Opt
DS8034-R
350 MHz
4
1, Opt
Manuals of this Product:
Quick Guide, User Guide, Programming Guide, Data sheet, etc. For the latest version
of this manual, download it from the official website of RIGOL (www.rigol.com).

Contents RIGOL
DS8000-R User Guide XIII
Contents
Guaranty and Declaration .........................................................................I
Safety Requirement ................................................................................ II
General Safety Summary...........................................................................II
Safety Notices and Symbols...................................................................... IV
Measurement Category ............................................................................. V
Ventilation Requirement ............................................................................ V
Working Environment .............................................................................. VI
Care and Cleaning ..................................................................................VII
Environmental Considerations.................................................................VIII
DS8000-R Series Overview .................................................................... IX
Document Overview................................................................................. X
Chapter 1 Quick Start .........................................................................1-1
General Inspection ................................................................................ 1-2
Appearance and Dimensions................................................................... 1-3
To Prepare for Use................................................................................. 1-4
To Connect to AC Power .................................................................. 1-4
To Connect to the Display and the Control Device .............................. 1-4
Turn-on Checkout ........................................................................... 1-5
To Replace the Fuse ........................................................................ 1-6
To Connect the Probe...................................................................... 1-6
Function Inspection......................................................................... 1-8
Probe Compensation ....................................................................... 1-9
Front Panel Overview............................................................................1-10
Rear Panel Overview.............................................................................1-10
User Interface......................................................................................1-14
Common Operation ..............................................................................1-17
Click Operation ..............................................................................1-17
Drag Operation..............................................................................1-18
Scroll Operation .............................................................................1-18
Rectangle Drawing.........................................................................1-18
Parameter Setting Method ..............................................................1-21
To Use the Built-in Help System .............................................................1-22
To View the Option Information and the Option Installation......................1-23
Chapter 2 To Set the Vertical System .................................................2-1
To Enable or Disable the Analog Channel ................................................. 2-2
To Adjust the Vertical Scale .................................................................... 2-2
Vertical Expansion ................................................................................. 2-3
To Adjust the Vertical Offset ................................................................... 2-3
Channel Coupling .................................................................................. 2-4
Bandwidth Limit .................................................................................... 2-5

RIGOL Contents
XIV DS8000-R User Guide
Probe Ratio ...........................................................................................2-5
Input Impedance ...................................................................................2-6
Waveform Invert ....................................................................................2-7
To Set the Probe ....................................................................................2-7
Passive Probe..................................................................................2-8
Active Probe....................................................................................2-8
Amplitude Unit.......................................................................................2-9
Channel Delay .......................................................................................2-9
Offset Cal ............................................................................................2-10
Channel Label......................................................................................2-11
Chapter 3 To Set the Horizontal System ............................................ 3-1
To Adjust the Horizontal Time Base..........................................................3-2
To Adjust the Horizontal Position..............................................................3-2
Delayed Sweep ......................................................................................3-3
Chapter 4 To Set the Sample System ................................................. 4-1
Timebase Mode .....................................................................................4-2
YT Mode.........................................................................................4-2
XY Mode.........................................................................................4-2
ROLL Mode .....................................................................................4-4
Acquisition Mode....................................................................................4-5
Normal ...........................................................................................4-5
Average..........................................................................................4-5
Peak...............................................................................................4-6
High Resolution ...............................................................................4-6
Sampling Mode ......................................................................................4-7
Sample Rate ..........................................................................................4-7
Memory Depth.......................................................................................4-9
Anti-Aliasing ........................................................................................4-10
Horizontal Expansion ............................................................................ 4-10
Chapter 5 To Trigger the Oscilloscope................................................ 5-1
Trigger Source .......................................................................................5-2
Trigger Level..........................................................................................5-3
Trigger Mode .........................................................................................5-4
Trigger Coupling.....................................................................................5-5
Trigger Holdoff.......................................................................................5-5
Noise Rejection......................................................................................5-6
Trigger Type ..........................................................................................5-7
Edge Trigger ...................................................................................5-8
Pulse Trigger ...................................................................................5-9
Slope Trigger................................................................................. 5-11
Video Trigger.................................................................................5-14
Pattern Trigger .............................................................................. 5-16
Duration Trigger ............................................................................ 5-18
Timeout Trigger.............................................................................5-20

Contents RIGOL
DS8000-R User Guide XV
Runt Trigger ..................................................................................5-22
Window Trigger .............................................................................5-24
Delay Trigger.................................................................................5-26
Setup/Hold Trigger.........................................................................5-28
Nth Edge Trigger............................................................................5-30
RS232 Trigger (Option)...................................................................5-32
I2C Trigger (Option).......................................................................5-34
SPI Trigger (Option) .......................................................................5-37
CAN Trigger (Option)......................................................................5-39
FlexRay Trigger (Option).................................................................5-42
LIN Trigger (Option).......................................................................5-44
I2S Trigger (Option) .......................................................................5-46
MIL-STD-1553 Trigger (Option) .......................................................5-49
Zone Trigger ........................................................................................5-52
Trigger Output Connector......................................................................5-54
Chapter 6 Operations and Measurements...........................................6-1
Math Operation ..................................................................................... 6-2
Addition ......................................................................................... 6-2
Subtraction .................................................................................... 6-3
Multiplication.................................................................................. 6-4
Division.......................................................................................... 6-5
FFT ............................................................................................... 6-6
"AND" Operation............................................................................. 6-9
"OR" Operation..............................................................................6-10
"XOR" Operation............................................................................6-11
"NOT" Operation............................................................................6-12
Intg..............................................................................................6-13
Diff...............................................................................................6-14
Sqrt..............................................................................................6-14
Lg (Base 10 Exponential)................................................................6-15
Ln ................................................................................................6-16
Exp ..............................................................................................6-17
Abs ..............................................................................................6-17
Low Pass.......................................................................................6-18
High Pass......................................................................................6-19
Band Pass .....................................................................................6-20
Band Stop .....................................................................................6-21
AX+B............................................................................................6-22
Math Operation Label .....................................................................6-22
Auto Measurement ...............................................................................6-24
Quick Measurement after AUTO.......................................................6-24
Measurement Parameter.................................................................6-26
Measurement Settings....................................................................6-32
Remove the Measurement Result.....................................................6-35
Statistical Function.........................................................................6-35

RIGOL Contents
XVI DS8000-R User Guide
All Measurement............................................................................6-36
Cursor Measurement ............................................................................6-36
Manual Mode ................................................................................ 6-37
Track Mode ................................................................................... 6-41
XY Mode.......................................................................................6-43
Measure Mode...............................................................................6-44
Chapter 7 Digital Voltmeter (DVM) and Frequency Counter............... 7-1
Digital Voltmeter (DVM) ..........................................................................7-2
To Enable or Disable DVM Measurement ............................................7-2
To Select the Measurement Source....................................................7-3
To Select Measurement Mode ...........................................................7-3
To Set the Limits .............................................................................7-3
Frequency Counter.................................................................................7-4
To Enable or Disable the Frequency Counter.......................................7-4
To Select the Measurement Source....................................................7-4
To Select the Measurement Item.......................................................7-4
To Set Resolution.............................................................................7-5
To Clear Count ................................................................................7-5
To Enable or Disable the Statistical Function.......................................7-5
Chapter 8 Power Analysis (Option) .................................................... 8-1
Power Quality ........................................................................................8-2
To Select the Analysis Type...............................................................8-2
To Set the Power Quality Analysis Source...........................................8-2
To Set the Reference Level ...............................................................8-2
To Set Count ...................................................................................8-3
To Reset .........................................................................................8-3
To Open or Close the Results Display Window ....................................8-3
To View the Connection Diagram.......................................................8-3
Ripple ...................................................................................................8-4
To Select the Analysis Type...............................................................8-4
To Set the Ripple Analysis Source......................................................8-4
To Set Count ...................................................................................8-4
To Reset .........................................................................................8-4
To Open or Close the Results Display Window ....................................8-5
To View the Connection Diagram.......................................................8-5
Chapter 9 Histogram Analysis ............................................................ 9-1
To Enable or Disable the Histogram Function ............................................9-2
To Select the Histogram Type ..................................................................9-2
To Select the Histogram Source ...............................................................9-3
To Select the Measurement Item .............................................................9-3
To Set the Histogram Height ...................................................................9-3
To Set the Histogram Range....................................................................9-3
To Enable or Disable the Statistical Function .............................................9-4
To Reset................................................................................................9-4

Contents RIGOL
DS8000-R User Guide XVII
Chapter 10 Real-time Eye Diagram and Jitter Analysis (Option) ........10-1
Real-time Eye Analysis ..........................................................................10-2
To Enable or Disable the Eye Analysis Function .................................10-2
To Select the Eye Source ................................................................10-2
To Set the Threshold ......................................................................10-2
To Set Clock Recovery ....................................................................10-3
To Enable or Disable the Eye Measurement Result.............................10-4
To Reset Color ...............................................................................10-5
Persistence....................................................................................10-5
Jitter Analysis.......................................................................................10-6
To Enable or Disable the Jitter Analysis Function ...............................10-6
To Select the Jitter Source ..............................................................10-6
To Set the Threshold ......................................................................10-7
To Set Clock Recovery ....................................................................10-7
To Set the Jitter Measurement.........................................................10-7
To Enable or Disable the Jitter Measurement Result...........................10-9
To Reset .....................................................................................10-10
Chapter 11 Protocol Decoding ............................................................11-1
Parallel Decoding..................................................................................11-2
RS232 Decoding (Option)......................................................................11-6
I2C Decoding (Option) ........................................................................11-12
SPI Decoding (Option) ........................................................................11-16
LIN Decoding (Option)........................................................................11-20
CAN Decoding (Option).......................................................................11-25
FlexRay Decoding (Option)..................................................................11-29
I2S Decoding (Option) ........................................................................11-33
1553B Decoding (Option)....................................................................11-36
Chapter 12 Reference Waveform........................................................12-1
To Enable Ref Function .........................................................................12-2
To Select the Reference Channel............................................................12-2
To Select the Ref Source .......................................................................12-2
To Adjust the Ref Waveform Display.......................................................12-2
To Save to Internal Memory ..................................................................12-3
To Clear the Display of the Reference Waveform......................................12-3
To View Details of the Reference Waveform ............................................12-3
To Reset the Reference Waveform..........................................................12-3
Color Setting........................................................................................12-4
Label Setting........................................................................................12-4
To Export to Internal or External Memory ...............................................12-4
To Import from Internal or External Memory ...........................................12-5
Binary Data Format (.bin)......................................................................12-5
Binary Header Format ....................................................................12-5
Chapter 13 Pass/Fail Test...................................................................13-1
To Enable or Disable the Pass/Fail Test Function ......................................13-2

RIGOL Contents
XVIII DS8000-R User Guide
To Start or Stop the Pass/Fail Test Operation...........................................13-2
To Select the Source.............................................................................13-2
To Create a Mask .................................................................................13-3
To Save a Mask....................................................................................13-3
To Load a Mask....................................................................................13-3
To Set the Output Form of the Test Results.............................................13-4
To Enable or Disable the Display of the Statistics of the Test Results .........13-4
Statistics Reset ....................................................................................13-5
Chapter 14 Waveform Recording & Playing ....................................... 14-1
Common Settings.................................................................................14-2
Record Options ....................................................................................14-3
Play Options ........................................................................................14-4
Chapter 15 Search and Navigation Function ...................................... 15-1
Search Function ...................................................................................15-2
To Enable or Disable the Search Function......................................... 15-2
To Select the Search Type and Set the Parameters............................15-2
To Copy Trigger .............................................................................15-3
To Open or Close the Mark Table..................................................... 15-3
To Navigate...................................................................................15-4
To Save ........................................................................................15-4
Navigation Function..............................................................................15-4
Chapter 16 Display Control ................................................................ 16-1
To Select the Display Type .................................................................... 16-2
To Set the Persistence Time ..................................................................16-2
To Set the Waveform Intensity .............................................................. 16-2
To Set the Screen Grid..........................................................................16-3
To Set the Grid Brightness.....................................................................16-3
Scale ..................................................................................................16-3
Color Grade .........................................................................................16-4
Waveform Freeze .................................................................................16-4
Chapter 17 Function/Arbitrary Waveform Generator (Option) .......... 17-1
To Output Basic Waveforms ..................................................................17-2
To Output Sine ..............................................................................17-2
To Output Square ..........................................................................17-3
To Output Ramp ............................................................................17-3
To Output Pulse.............................................................................17-4
To Output DC ................................................................................ 17-4
To Output Noise ............................................................................ 17-5
Sinc.............................................................................................. 17-5
Exp.Rise .......................................................................................17-5
Exp.Fall......................................................................................... 17-6
ECG .............................................................................................17-6
Gauss........................................................................................... 17-6
Lorentz......................................................................................... 17-7