Rimage Professional 5100N Parts list manual

DiscLab™ Operator
2000509_B © 2007, Rimage Corporation 1
Replace the Hard Drives on a Rimage 5100 or Rimage 5300N
Use this procedure to replace the hard drives as a set on a Rimage 5100N™ and Rimage 5300N™.
The procedures in this document should be performed only by personnel trained and authorized by Rimage. The instructions and
content are written for mechanical and electrical service work assuming the technician has such training and authorization. The
product warranty may become void if equipment or parts are tampered with, misused, neglected, or modified in any respect without
the written consent of Rimage or by technicians who are not authorized or certified by Rimage.
-Important! The hard drives must be replaced as a set.
Before you begin
1. Stop or pause all jobs.
2. Power off the embedded control center.
3. Power off the system.
4. Disconnect the power cord from the power outlet.
#equired tools:R
•Phillips or flathead screwdriver (5100N only)
Remove the hard drives
1. At the left side of the 5100N, loosen the screws (Qty. 2) on the left side cover.
OR
At the rear of the 5300N, loosen the thumbscrew (Qty. 1) on the hard drive cover.
2. Remove the left side cover (5100N) or hard drive cover (5300N).
5100N
Left
Side
Cover
Hard
Drive
Cover
5300N
3. Remove the hard drives.
a. Insert your thumb and finger into the tabs on the hard drive.
b. Squeeze the tabs together.
c. While squeezing the tabs, pull the hard drive out of the system.
d. Repeat steps a – c for the second hard drive.
Hard Drive
5100N 5300N

Replace the Hard Drives on a Rimage 5100 or Rimage 5300N
Install the hard drives
1. Hold a replacement hard drive so that the label on the top of the hard drive faces the front of the system
(5100N) or the power supply (5300N - toward the right when looking at the unit from the rear).
2. Gently insert the hard drive all the way into hard drive bay 0.
Tips:
•Press on the hard drive, not on the tabs, to insert the hard drive.
•The hard drive is installed when it snaps into place.
3. Hold the second replacement hard drive so that the label on the top of the hard drive faces the front of the
system (5100N) or the power supply (5300N - toward the right when looking at the unit from the rear).
4. Gently insert the hard drive all the way into hard drive bay 1.
5. Position the left side panel (5100N) or the hard drive cover (5300N) on the unit.
6. Tighten the screws (Qty. 2, 5100N) or the thumb screw (Qty. 1, 5300N) to secure the cover.
7. Connect the power cord.
8. Run the recovery disc(s). Refer to the instructions included with your recovery disc(s).
The system is ready for use.
Support information
Europe When you contact Rimage Services, please provide:
Contact Rimage Services Europe:
www.rimage.com/support.html
Email: [email protected]
Tel: [phone]
•Unit serial number and software version.
•Functional and technical description of the problem.
•Exact error message received.
US, Asia/Pacific, Mexico/Latin America Rimage Corporation reserves the right to make improvements to the
Contact Rimage Services: equipment and software described in this document at any time without
any prior notice. Rimage Corporation reserves the right to revise this
www.rimage.com/support.html publication and to make changes from time to time in the content hereof
Email: http://www.rimage.com/support_form.cfm without obligation of Rimage Corporation to notify any person or
Tel: North America: 800-553-8312 organization of such revisions or changes.
Asia/Pacific, Mexico/ Latin America: 952-946-0004
2000509_B © 2007, Rimage Corporation 2