Rimage AMIGO II EVEREST Instructions for use

Amigo II
Maintain the Amigo II
Maintenance schedule
Task Frequency
Once a week. Remove dust from Amigo II and surrounding work
area using a lint-free cloth.
Clean the Amigo II
Upon installation and again if the discs are not picked correctly from
the printer tray. Refer to the procedures below for more information.
Align the printer
Note: For information on cleaning and maintaining your printer, refer to your Everest Printer User Guide
or PrismPlus! Printer User Guide.
Everest Printer
To align your Everest Printer, refer to the following instructions.
Required tools:
yT 25 Torx screwdriver
y5/32” Allen wrench
1. To power on the Amigo II, press the Amigo II power switch.
2. Wait until the unit completes the initialization.
Tip: The Everest II Printer takes 1 to 2 minutes to complete the initialization.
3. Prepare the unit for alignment.
a. Manually move the lift arm to the top of the
Amigo II.
b. To place a disc in the lift arm, press the
disc up into the Lift Arm while pressing the
disc release button.
c. To open the print drawer, press the printer
button.
d. Close and re-open the door of the Amigo II.
This releases the lift arm so you can
manually move it.
Lift
Arm
Gri
pp
e
r
Disc Release Button
110654_G 1

Amigo II
2110654_G
4. Align the printer.
a. Slowly move the lift arm down until the disc just touches the print pad.
Printer
Button
Lift
Arm
Side to Side
Alignment
Print
Pad
Holding
Pins
b. If the disc is not centered side to side on the print pad, align the printer side to side.
i. Loosen the side to side screws.
ii. Slide the printer, not the print drawer,
until the side edges of the disc and
printer pad are aligned.
iii. Tighten the side to side screws.
Side to Side
Screws
Front to Back Screw
c. Using either the T25 Torx driver or the
5/32” Allen wrench, turn the front to back
alignment screw until there is a 1/16”
(1.5mm) gap between the front edge of the
disc and the raised edge of the disc
retainer.
Gap
Disc
Retainer
5. Raise the lift arm out of the way of the print drawer.
6. To close the print drawer, press the printer button.
7. To release the disc from the gripper, press the disc release button.
Tip: Place your hand under the disc to catch it.

Amigo II
PrismPlus printer
To align your PrismPlus printer, refer to the following instructions.
Required tools:
yT 25 Torx screwdriver
y5/32” Allen wrench
1. To power on the Amigo II, press the PrismPlus power switch and the Amigo II power switch.
2. Wait for the unit to complete the initialization.
3. Prepare the unit for alignment.
a. Manually move the lift arm to the top of the
Amigo II.
b. To place a disc in the lift arm, press the
disc up into the lift arm while pressing the
disc release button.
c. To open the print drawer, press the printer
button.
d. Close and re-open the door. This releases
the lift arm so you can manually move it.
Lift
Arm
Gri
pp
e
r
Disc Release Button
4. Align the printer.
a. Slowly move the lift arm down until the disc just touches the print pad.
Printer
Button Lift
Arm
Side to Side
Alignment
Print
Pad
Holding Pins
110654_G 3

Amigo II
4110654_G
b. If the disc is not centered side-to-side on
the print pad, align the printer side to side.
i. Loosen the side to side screws.
ii. Slide the printer, not the drawer, until
the side edges of the disc and printer
pad are aligned.
iii. Tighten the side to side screws.
Side to Side Screws
Front to Back
Alignment Screw
c. Using either the T25 Torx driver or the
5/32” Allen wrench, turn the front-to-back
alignment screw until the disc hangs over
the edge of the print pad by 0.010” –
0.015”.
Print Pad
5. Raise the lift arm to the top the unit.
6. To close the print drawer, press the printer button.
7. To release the disc from the gripper, press the disc release button.
Tip: Place your hand under the disc to catch it.
8. Close the door.