Rinnai Symmetry RDV3611 User manual

Rinnai NZ Ltd Page 1 of 2 11154 Issue B
RDV3611 : SYMMETRY
Vertical Flue Up Rating Instructions (ULPG ONLY)
Must be installed by a certified gas fitter in accordance with all applicable local rules and regulations
The Rinnai Symmetry RDV3611 LPG appliance is factory supplied, with rated input of 30MJ/hr for
installation for Horizontal Vent Terminations only. To ensure that optimum Flame Effect and
Maximum Energy Efficiency is obtained when the unit is being installed with a Vertical Vent
Termination the appliance must be up rated to 33MJ/hr by installing this Kit.
Kit Contents
Quantity
Rinnai Part Number
Comments
Main Injector
1
11534
1.70mm
Data Plate
1
11152
For Vertical Flues ONLY
Instruction Sheet
1
11154
Energy Rating Label (Vertical Flue)
1
Gas Up Rating Procedure
1. Remove Glass assembly 4 x screws; lift and remove.
2. Remove service panel front 2x screws.
3. Remove service panel rear 2x screws; Lift panel out carefully and put to one side (leaving the
CAT5 cable connected to control panel receiver).
4. Remove log set if installed.
5. Remove burner cover.
6. Lift the burner assembly out carefully as it is very fragile. NOTE: Extra care should be taken to
avoid scratching the ceramic panels/ combustion chamber walls.
7. Remove and replace the Main Injector with the one supplied.
8. Gently lift the burner assembly back into place. NOTE: Extra care should be taken to avoid
scratching the ceramic panels/ combustion chamber walls.
9. Refit the burner cover.
10. Install the log set.
11. Fit the Field Converted Data Plate next to the existing dataplate to show that it has been field
up rated
12. Commission & set gas pressures for correct gas type as per gas setting procedure.
13. Reassemble the remaining components in reverse order.
Burner Cover
Burner assembly
Main injector
Pilot head

Rinnai NZ Ltd Page 2 of 2 11154 Issue B
RDV3611 : SYMMETRY
Vertical Flue Up Rating Instructions (ULPG ONLY)
INSTALLERS INFORMATION - TESTING & COMMISSIONING
TESTING PROCEDURE
Turn gas supply on and plug the unit into the
power supply. (Caution 240V.)
TO CHECK BURNER PRESSURE
• Refer to Data Plate; the Technical Specification
section in the service manual.
• Loosen the Outlet Test Point screw and attach
manometer to the test point. The Outlet Test
Point is on the right hand side of Gas Control
(Shown Below)
• Light appliance, adjust to High flame setting
and check pressure.
• If adjustments are necessary, remove the Cap
C. Pressure adjustment screw and nut are on the
front side of Gas Control (Shown Below) and
should be set to the pressures on the data-plate.
High Pressure Setting: Set the POV to the
maximum condition. Use 10mm spanner to screw
in Nut A to increase the outlet pressure and
screw it out to decrease the pressure.
Low Pressure Setting:
Turn off the power to the POV by disconnecting the
POV Test Connection (yellow wires) in main harness.
Keep Nut A stationary, use a screwdriver 6X1 blade
to screw in the Screw B to increase the pressure and
screw it out to decrease it.
Carefully replace the modulator plastic cap.
WARNING: To ensure the correct operation of the
POV it is necessary that the plastic cap C is returned
to its original location.
• After checking the pressure, turn the unit off,
remove manometer and tighten the test point screw.
(reconnect the POV connection in the main harness)
• Turn the appliance on and off a few times to check
ignition.
• When you are satisfied that the appliance is
working correctly, refit the service panels. Refit the
glass assembly and frame(s).
• If you are unable to get the unit to operate
correctly, refer to Troubleshooting in the service
manual before contacting your local service agent.
• It may take approximately 2 hours of operation for
the media to achieve their full flame pattern and
glow.
• During the initial burning in period, some smoke
and smell may be experienced; the appliance should
be run on the high position in a well ventilated room
until these dissipate.
INLET TEST POINT
OUTLET
TEST POINT
C: CAP
A: HIGH PRESSURE
ADJUSTING NUT
B: LOW PRESSURE
ADJUSTING SCREW