RIOTEC RIOSCAN iLS6300FS User manual

1
RIOSCAN Laser Barcode Scanner
Quick Guide
Model no.:
iLS6300FS
Introduction
Designed primarily for smartphone, the iLS6300FS is a 1D barcode
scanner that allows you to scan various barcoded items and send data
to smartphone.
Its in-built 1D Laser Engine allows you to reliably read 1D barcodes on
various shapes and is a great space-saver for busy or limited
workspaces.
It supports not only iOS devices through wireless communication,
but also Android OTG devices through USB cable
Technical data
*Light source………………650 nm Laser Diode
*Depth of field……….….. 520 mm (40mil)
*Scan speed………………. 100 scans/sec
*Best resolution…………. 4 mil
*Transmission range……BT Class 1 (100m, line of sight)
*Profiles………….…………BT HID & SPP profile
*Memory Capacity………1MB memory inside
*Input voltage..............5V/DC
*Rechargeable battery... AA NiMH rechargeable battery
1.2V x 2 ( 2.4V 2300mAH)
*Operating time…………. more than 25,000 scans when fully
charged
*Operating conditions…-0℃to 50℃
* Dimensions………………203 X 60 X 95 mm (for scanner)
* Symbologies: "UPC/EAN/JAN, Code11, Code 39, Code 32 (Italian
pharmacy), Code 93,Code 128, CODABAR, Matrix 25, Interleave 25,
Industrial 25, China Post
Delivery content
*Wireless Barcode scanner x 1
*Charging cradle x 1
*PCB material board+3 screws x 1
*Holder for smartphone x 1
*USB cable x 1
*Quick instructions x 1
Limited Warranty
Riotec provides a one year limited warranty.
This warranty does not cover any product which has been subject to
improper use, neglect or unauthorized repair or installation.
This warranty does not cover consumable parts. (Cables & batteries are
consumables.)
Safety instructions
*The product is equipped with a Class 1 laser.
*Never look into the laser beam and never point it at people or animals.
Laser radiation can seriously damage your eyes.
*Do not point the laser beam at mirrors or other reflective surfaces. The
uncontrolled, reflected beam may strike people or animals.
*Don’t put scanner in places excessively high temperatures, such as
expose under direct sunlight.
*Don’t use scanner in extremely humid area or drastic temperature
change
*The rechargeable battery is permanently built into the product and
cannot be replaced.
*Never damage the rechargeable battery. Damaging the casing of the
rechargeable battery might cause an explosion or a fire!
Charging:
1. Please switch on and charge scanner for 3~4 hours before first use as
shown on Fig.
2. When user charge smartphone & scanner, please use smartphone
original USB power adapter
3.
The cradle functions as a charger for the scanner. Even if the scanner’s
battery is full, the cradle will continue to supply power to the scanner.
We suggest removing the scanner from the cradle when fully charged.
4. When you charge scanner & smartphone, please enter Wired OTG
mode & switch to “C- Charging mode”.

2
iLS6300FS supports BT communication mode (for iOS) and wired
OTG communication mode (for Android OTG devices)
If you want to switch to another mode, please read the below configuration
code first.
wireless communication
wired OTG communication mode
(default)
Operating elements
*Please switch ON and charge scanner for 3~4 hours at first
time before use.
How to Connect to Smartphone via BT
1. Make sure the default is BT mode (page #2) & your device
has BT HID or SPP profile
2. Turn off Power-Saving mode on your smartphone/tablet
3. Then, choose HID or SPP profile and scans the following 2
settings codes before connecting to smartphone/tablet.
(A1 A2 or B1 B2)
If you don’t know which profile to choose for your device, try
HID first, then, SPP.
HID profile
SPP profile
A1
B1
A2
B2
4. Please complete the connection procedures as the above
photos.
5. After the devices are paired, the screen will show
“Connected”. (see step #6 above)
6. Before using WordPad file or appropriate APP, please set
keyboard language of device to US English. Then, scan the
barcodes and the barcode data will show on the cursor side. If
the data cannot be sent to smartphone/tablet, please scan the
“Reset Configuration to Defaults” setting codes (on page #3).
1. click the “Settings”
2. click “General”
3. click “Bluetooth”
4. Turn it ON, and search the
Devices
5. Select “Rxxxxxx” to connect
6. When see the “Connected”
means the connection is OK.
(example: pairing with iPhone)
Trigger / Power ON
Button
(For iOS Device ONLY)
P
ress the trigger for 4~5
seconds to
raise and
lower soft-Keyboard
Exit
Window
Mic
ro USB port
U
se Micro USB cable to
connect to smartphone.
Charging
cradle
Indicator
(LED)

3
Notes 1:
*This product complies with Bluetooth standards. This device used
with this product must support the same SPP or HID standard. For
Bluetooth devices with other profiles we cannot guarantee a
connection before the product has been tested.
*The communication speed and range of the product may vary due to
obstacles and radio interference between the product and device.
Condition on the host device may also effect the communication
speed and range of the scanner
Note 2:
*When the battery power is too low, the Orange LED will flash
and beep once. Scanner should be charged immediately. If
scanner shuts down it is recommended to charge it fully then
power it back on.
Reset Configuration to Defaults
(scan from A1 to A5 for HID profile or B1 to B6 SPP profile)
HID profile
SPP profile
A1
B1
A2
B2
A3
B3
A4
B4
A5
B5
B6
How to Connect to Smartphone via OTG cable
1. Make sure you enter wired OTG mode (page #2) and your
Android device supports OTG functionality.
2. Make sure scanner is in ”O” (OPERATION MODE)(see below)
3. Connect scanner to Android OTG device through micro USB cable.
4. Scan the barcode
5. Open app on smartphone/tablet & data will be sent to the app
directly
After the scanner connects to your iOS device and is inserted into
cradle, it may display the above message.
If this happens, remove and reinsert device into cradle.
LED Indicator Information
Orange LED ON
Full charged
Orange LED Flashing
Charging / Low battery
Red LED ON
Offline / out of service
Green LED ON
Good read
Orange LED ON
Good read (Batch mode)
Before entering BT mode, you
must
switch to right
“
Charging mode” first.
Then, cradle can supply
power to iOS / Android device
(through micro USB cable) &
scanner simultaneously.
Indicator (LED)
Please check the
“LED
Indicator Information
” on
page #3
Switch to left:
“O” (
Operation mode
)
(data transmission)
Switch to right:
“C” (
Charging mode)
Indicator (LED)
Please check the
“
LED Indicator
Information”

4
Keyboard Country
(Wired OTG mode only)
Scan the appropriate country code as below to program the
keyboard layout for your country or language. As a general
rule, the following characters are supported, but need special
care for countries other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~
USA
(Original setting)
Italian
Norway
France
Germany
Vietnam
Sweden
Spain
Denmark
Portugal
Switzerland
Hungary
PCB material board with 3 fixed screws.
1. Make sure your micro USB cable is ready.
User can adjust micro USB cable to the right channel based on the
location & direction of micro USB port on the smartphone.
2. Lock PCB material board on the top cover by 3 screws
3. There are another 3 fixed screws on the PCB material board.
Aiming at fixed screws put holder on them pull down and left
for locking
(The transparent acrylic board is for reference only)
1. The holder is stuck on the top cover by 3 fixed screws.
2. Put smartphone onto holder. It will use PU glue & suction cup to fix
smartphone. And, user can plug micro USB cable to
smartphone. Then, user can begin to do the BT pairing or wired
connection.
3. When the pairing is completed, the data you scan will be sent to
smartphone easily.
Holder
PCB material board
with 3 fixed screws.
Holder-back side
(for top cover)
Holder-front side
(for smartphone)

5
There are two operating modes on the scanner
1.Data Transmission mode(Default)
It is a necessary to scan “clean memory data” when
switching between these two modes.
Within 2.4GHz radio range
Beyond 2.4GHz radio range
Data
read Transmit data to smartphone/tablet directly
Save data in scanner’s memory,
scanner will transmit data to
smartphone/tablet automatically
after getting back to 2.4GHz radio
range.
Enter Data Storage mode
LED
Green/ Orange LED flashes,
followed by 3 beeps.
2. Data Storage mode(Batch Mode)
It is a necessary to scan “clean memory data” when
switching between these two modes.
Data
read
Save data directly to scanner’s memory. It will transmit data to
smartphone/tablet after you scan the Transmit memory data
code. To delete data, please scan the Clean memory data code.
Enter Data Transmission mode
LED
Green/ Orange LED flashes followed by 3 beeps.
Always Clean memory data before switching to Data Transmission
Mode.
Otherwise Red/ Orange LED will flash with one long beep sounds
and will not switch modes.
A. Data Transmission mode
(Default)
1.
When you are out of BT signal range,
the data you scan will be saved to
memory. Once you are back within
range, the data will be sent to
smartphone/tablet automatically.
B.
Data Storage mode(Batch mode)
1.
Data Storage mode (Batch mode):
When you scan the barcodes, the data
will be saved directly to scanner’s
memory. After you scan the
“Transmit memory data” code
(above right), the data will be sent to
smartphone/tablet.
2.
Before you can continue to scan or
switch modes, you must first delete
the data stored in the memory. To do
this, scan the “Clean memory data”
code. (below right)
Transmit memory data
Green/Orange LED flashes
followed by 3 beeps
The barcode data which is stored
in the memory will be sent to
smartphone/tablet directly.
(under Batch mode, within
Bluetooth service range)
Clean memory data
Green/Orange LED flashes
followed by 3 beeps.
The barcode data which is stored
in the memory will be deleted. You
can then switch modes.
Transmission Speed
Transmission speed is dependent on your device. In order not
to lose data, please choose the correct speed. Middle-speed is
the Default.
High-speed transmission
(for HID, SPP)
Middle-speed transmission
(for HID only, HID Default)
Slow-speed transmission
(for HID/SPP, SPP Default)
Ultra Slow-speed 1 transmission
(for HID only)
Ultra Slow-speed
2
transmission
(for HID only)
Ultra Slow-speed 3 transmission
(for HID only)
Power-saving Mode
Power-saving mode OFF
Power-saving mode ON (Default):
Enter power-saving mode after one
minute inactivity. This function
conserves battery power. When you
press the "SCAN/Power ON" button, it
will wake up and begin to scan.
*When charging, the scanner will not enter power-saving mode
automatically.
Battery information
When you scan this setting
code, scanner will output the battery
information to device.
Output battery information
automatically – Enable
Will send data to device
every 30 seconds.
Output battery information
automatically – Disable.
The output format of battery information is as below:
For example: %^4^%
%^NUMBER^% Number is from 0~4.
4 means 80%~100%
3 means 55%~80%
2 means 30%~55%
1 means 10%~30%
0 means under 10% -- When output reads “0”, it means low
battery power and device should be charged immediately.

6
Barcode Configuration Method:
(Flow chart for setup procedure :)
Start
Configuration
End
Configuration
1D Symbologies – 1
ENABLE
UPC-E
DISABLE
ENABLE
UPC-A
EAN13
DISABLE
ENABLE
EAN8
DISABLE
ENABLE
CODE 39
DISABLE
1D Symbologies – 2
ENABLE
CODE 93
DISABLE
ENABLE
CODE 11
DISABLE
ENABLE
CODE 128
EAN/UCC 128
DISABLE
ENABLE
INTERLEAVED 25
DISABLE
ENABLE
STANDARD 25
INDUSTRIAL 25
DISABLE
ENABLE
MATRIX 25
DISABLE
ENABLE
CHINESE POST
DISABLE
1D Symbologies – 3
ENABLE
CODABAR
DISABLE
Quick guide is subject to change without notice.
R_161020_01