RIOTEC LS6300E User manual

Programming Quick Guide
LS6300E/LS6320E./FS5020E
Installation
Make sure that the scanner has the correct cable to
plug into the PC as below described:
1.USB cable connection/ PS2 cable connection:
(Please use correct cable for the interface)
Reset Configuration to Default
If you are unsure of the scanner configuration or have
scanned the incorrect codes, please read the “Default”
barcode. This will reset the scanner to its factory
default.
Default
2.RS232 cable connection:
Please read above “Default” first,
and then set the output mode as
RS232 (SERIAL).
★If you want to switch to different interface, please
scan the correct configuration code (Output Mode,
right above), then, change the appropriate cable.
3.Auto-sensing setup
The auto-sensing will be activated while scanner puts
on stand. When scanner is removed from stand, it
becomes trigger mode.
OUTPUT MODE –
KEYBOARD / USB
OUTPUT
MODE
OUTPUT MODE
- RS232 (SERIAL)
SINGLE SCAN
READING
MODE SINGLE SCAN
NO TRIGGER
LASERTIMEOUT
–5 SECONDS
LASER TIMEOUT
–2 SECONDS
CODE 11 DOUBLE
CHECK -ENABLE
DOUBLE
CHECK
CODE 11 DOUBLE
CHECK -DISABLE
CODE 39 DOUBLE
CHECK -ENABLE
CODE 39 DOUBLE
CHECK -DISABLE
CODE 93 DOUBLE
CHECK -ENABLE
CODE 93 DOUBLE
CHECK -DISABLE
CODE 128 DOUBLE
CHECK -ENABLE
CODE 128 DOUBLE
CHECK -DISABLE
MSI DOUBLE
CHECK-ENABLE
MSI DOUBLE
CHECK -DISABLE
I2OF5 DOUBLE
CHECK -ENABLE
DOUBLE
CHECK
I2OF5 DOUBLE
CHECK -DISABLE
ID2OF5 DOUBLE
CHECK -ENABLE
ID2OF5 DOUBLE
CHECK -DISABLE
CODABAR DOUBLE
CHECK -ENABLE
CODABAR DOUBLE
CHECK -DISABLE
UPC/EAN DOUBLE
CHECK -ENABLE
UPC/EAN DOUBLE
CHECK -DISABLE
REVERSE IMAGE
–ENABLE
IMAGE REVERSE IMANGE
-DISABLE
SEND BAR CODE ID
-DISABLE
CODE ID SEND BAR CODE
ID – AS A PREFIX
SEND BAR CODE ID
-RESET
SEND BAR CODE
ID –AS A SUFFIX

Keyboard Language
Scan the appropriate country code as below to program the keyboard
layout for your country or language. As a general rule, the following
characters are supported, but need special care for countries other
than the United States:@ | $ # { } [ ] = / ‘ \ < > ~
DENMARK
FINLAND
FRANCE
GERMANY
ITALY
LATIN AMERICA
NETHERLANDS
NORWAY
POLAND
SPAIN
SWITZERLAND
(FRENCH)
SWITZERLAND
(GERMAN)
SWEDEN
UNITED KINGDOM
UNIVERSAL
UNITED STATES
Symbologies -1
CODE 11
– ENABLE
CODE 11
CODE 11
– DISABLE
CODE 39
– ENABLE
CODE 39
CODE 39
– DISABLE
FULL ASCII
– ENABLE
FULL ASCII
– DISABLE
CODE 93
–ENABLE
CODE 93
CODE 93
–DISABLE
CODE 128
–ENABLE
CODE 128
CODE 128
– DISABLE
CODE 128 ISBT
–ENABLE
CODE 128 ISBT
– DISABLE
CODABAR
– ENABLE
CODABAR
CODABAR
–DISABLE
Symbologies -2
INTERLEAVED 2 OF 5
I2OF5 - ENABLE
I2OF5 - DISABLE
INDUSTRIAL 2 OF 5
ID2OF5 -ENABLE
ID2OF5 - DISABLE
MSI - ENABLE
MSI
MSI - DISABLE
UPC-A- ENABLE
UPC/EAN
UPC-A -DISABLE
UPC-E -ENABLE
UPC-E -DISABLE
EAN-13 -ENABLE
EAN-13 -DISABLE
EAN-8 -ENABLE
EAN-8 -DISABLE
Information in this document is subject to change without notice.
For more information, please visit:
www.riotec.com.tw R_20160824_01