RIOTEC iDC9277L User manual

1
Quick Guide
- iDC9277L
1
Connect to micro USB port of
Smartphone
2
3
*Before you use scanner, please switch to "C- Charge
mode" and charge inside battery for 3~4 hours first.
*Under “C- Charge mode”, you can raise/lower soft-
keyboard easily. (For HID profile only)
4
iDC9277L is with Li-Ion battery inside. When in charging,
please use the original USB power adaptor of
Smartphone (recommended). Through it, it charges both
smartphone & iDC9277L batteries at the same time.
When in low battery (Orange LED flashing), please
charge it immediately.
In case the power consumed out totally; the RTC (Real
Time Clock) will back to original setting 01012000.
Attention: Please don’t charge iDC9277L when in Operation
mode. Otherwise, the smartphone’s battery will charge back
to iDC9277L’s battery.
5
** When pressing Left button + Right button for 8~9
seconds, iDC9277L will enter deep sleeping mode.
** Please press Left button + Right button + Touch trigger
for 8~9 seconds to activate iDC9277L.
** The touch sensor area is around the central area.
Please check the above drawing for your reference.
LED Indicator Information
Orange LED ON
Full charged
Orange and Red LED Flashing
Charging
Orange LED Flashing
Low battery
Red LED ON
Off line / out of service
Green LED ON
Good read
Orange LED ON
Good read (Batch mode)
O=Operation mode
C=Charge mode
Left Button
Under BT HID Profile, press Left button to
raise/lower soft-Keyboard; press the left button for 4
seconds to un-pair. Then, scanner can be connected
with other BT devices (Please check page #2, left
column)
Touch Trigger Area
SCAN/ Power ON
Press 1 second to wake it
up from power saving
mode
Right Button
Power Saving button:
Press the button for 4 second
then enter power saving mode
Indicator
(LED)
Charge port
Suction Cup
PU Glue
(Can be used
repeatedly)
Micro USB
cable (OTG)
Exit Window
Li- Ion Battery inside
Indicator (LED)

2
How to Connect to Smartphone
1. Make sure your device has BT HID or SPP profile
2. Turn off Power-Saving mode on your smartphone first
3. Then, choose HID or SPP profile and scans the following 2
setting codes before connecting to smartphone.
(a1 a2 or b1 b2)
If you don’t know what profile your device is, please try HID
profile first, then, SPP profile.
HID profile
SPP profile
a1
b1
a2
b2
4. Please complete the connection procedures as the right photos.
5. After the connection is completed, the RED light will be OFF.
6. Before using WordPad file or appropriate APP, please set
keyboard language of device to User’s language. Then, scan
the barcodes and the barcode data will show on the cursor side.
Soft-Keyboard setting code for Android / iOS
For Android
For iOS
*Under Android system, if you want to raise/lower soft-keyboard, please
read the above setting code first. Then, press left button (refer to drawing
#5 on page #1) to raise keyboard (LED is RED /Bluetooth is offline), press
it again to lower keyboard (LED is off/ Bluetooth is online)
*It will take 5~10 seconds to make BT online/offline.
*Please be noted that when BT is offline, scanning function is
stopped.
*Or, switch “C” to “O” to make BT online. (Drawing 3, page #1)
*Under iOS system, press Left button to raise/lower soft-Keyboard;
*Press the left button for 4 seconds to un-pair. Then, scanner can be
connected with other BT devices
1. click the “Settings”
2. click “General”
3. click “Bluetooth”
4. Turn it ON, and search the
Devices
5. Select “Rxxxxxx” to connect
6. When see the “Connected”
means the connection is OK.
(example: pairing with iPhone)
Reset Configuration to Defaults
(scan from A1 to A4 for HID profile or B1 to B5 for SPP profile)
HID profile
SPP profile
A1
B1
A2
B2
A3
B3
B4
A4
B5
%H%I%D
%S%P%P
%B%R%C
%B%R%C
%A%N%R
%I%O%S
0006010
0006010
0001160
0001160
0006000
0310020
0006000
Demo
%D%F%T
Demo
%D%F%T

3
There are two operating modes on the scanner
1.Data Transmission mode (Default)
It is a necessary to scan “clean memory data" when
switching between these two modes.
Within Bluetooth radio
range
Beyond Bluetooth radio range
Data
read
Transmit data to
PC/terminal directly
Save data into scanner’s memory,
scanner will transmit data to PC/
terminal automatically when back to
Bluetooth radio range.
Enter Data Storage mode
LED
Green/ Orange LED flashes
followed by 3 beeps.
2.Data Storage mode (Batch Mode)
It is a necessary to scan “clean memory data" when switching
between these two modes.
Data
read
Save data directly to scanner’s memory, It will transmit the data to
PC/ terminal after you scan the Transmit memory data code. To
delete data please scan the Clean memory data code.
Enter Data Transmission mode
LED
Green/Orange LED flashes followed by 3 beeps.
Always Clean memory data before switching to Data Transmission
Mode. Otherwise Red/ Orange LED will flash with one long beep and
will not switch modes.
Under Data storage Mode
The data can be keep or delete by option after transmit
Keep the data
(Default)
Delete the data
Transmit memory data
Green/Orange LED Flashes followed by 3 beeps
Clean memory data
Green/Orange LED flashes followed by 3 beeps
The barcode data which is stored in the memory will be deleted.
Trigger Mode
Trigger always
(Trigger available at any time)
Trigger standard (Default)
(Trigger available, after data sent to the device)
Transmission Speed
Transmission speed is dependent on your device. In order not to lose
data, please choose the correct speed. Middle-speed is the Default.
High-speed
Ultra Slow-speed
transmission
1transmission
Middle-speed
Ultra Slow-speed
transmission
2transmission
Slow-speed
Ultra Slow-speed
transmission
(Default)
3transmission
Power-saving Mode
Power-saving mode OFF
Power-saving mode ON (Default):
Enter power-saving mode after 5-minute
inactivity. This function converses battery
power. When you press "SCAN/Power ON"
button, it will wake up and begin to scan.
Power-saving mode ON:
Enter power-saving mode after 10-minute
inactivity. This function converses battery
power. When you press "SCAN/Power ON"
button, it will wake up and begin to scan.
*When charging, the scanner will not enter power-saving mode
automatically.
RTC (Real-time clock),
please set the punctuation mark at the same time
You must scan the below configuration barcode to set the date &
time stamp on the scanner.
Date information:
ENABLE
Date information:
DISABLE (default)
Time information:
ENABLE
Time information:
DISABLE (default)
The format of Date setting
Date format 1: mm/dd/20yy (default)
For example: 01/23/2011
Date format 2: dd/mm/20yy
For example: 23/01/2011
Date format 3: 20yy/mm/dd
For example: 2011/01/23
The punctuation marks for the intervals among
barcode data, date, time
, comma (default) –FOR Android/iOS use
For example:
ABCD,01/23/2011,12:34:56
Tab –FOR iOS use
For example:
ABCD 01/23/2011 12:34:56
; semicolon –FOR Android/iOS use
For example:
ABCD;01/23/2011;12:34:56
Demo
%M%A%F
Demo
%M%A%N
Demo
%M%D%K
Demo
%M%D%E
Demo
%R%E%C
Demo
%E%R%A
Demo
%R%T%E
Demo
%R%T%D
Demo
%B%T%H
Demo
.
Demo
.
Demo
.
Demo
%B%T%L
Demo
.
Demo
%P%D%T00
Demo
%P%D%T05
Demo
%P%D%T10
Demo
%D%I%N
Demo
%D%I%F
Demo
%T%I%N
Demo
%T%I%F
Demo
.
Demo
.
Demo
.
Demo
%T%S%C,
Demo
%T%S%C
Demo
%T%S%C;

4
Date and Time setting
SET DATE
Scan the SET DATE barcode, then, scan the
six numeric digits in the format mm/dd/yy,
from the numeric barcode.
For example: “01/23/2011”, please input
012311
SET TIME
Scan the SET TIME barcode, then, scan the
six numeric digits in the format hh:mm:ss from
the numeric barcode. Time format: 24hr clock
For example: “PM 3:25:30”, please input
“152530”
Keyboard Country (For HID profile only)
Scan the appropriate country code as below
to program the keyboard layout for your
country or language. As a general rule, the
following characters are supported, but
need special care for countries other than
the United States: @ | $ # { } [ ] = / ‘ \ <
> ~
Follow the steps mentioned below to program.
1. Keyboard Country setting code.
2. “Select Country Code”
Read numeric barcode (according to country code).
Country/
Language
No.
Country/
Language
No.
Country/
Language
No.
U.S.
10
Netherlands
26
Switzerland
French
45
Latin
America
11
Hungary
27
Switzerland
German
46
Brazil
12
Italian
28
Sweden
47
Belgium
20
Icelandic
29
Turkey F
48
Bulgarian
Latin
21
Norway
30
Turkey Q
49
Denmark
22
Poland
41
Japan
71
Finland
23
Portugal
42
Korea
72
France
24
Russia
43
Thai
73
Germany
25
Spain
44
Vietnam
74
How to append a “prefix” or a “suffix” to the
barcode data
prefix
suffix
1. scan above configuration code for Prefix or Suffix
2. enter the required values (right, numeric barcode) for Prefix or Suffix
using the hex values for the desired HEX values from Prefix & Suffix
TABLE (below page)”
3. then, end by scanning Code X (below, right)
*The max. of special characters is 5.
*When you append 1~4 required values for Prefix or Suffix, it must end
with Code X.
*It doesn’t need Code X, if you append 5 values to barcode data.
How to delete Prefix or Suffix
1. scan above configuration code for Prefix or Suffix
2. enter the “0” “0” (above, left)
3. then end by scanning Code X (below, right)
Numeric barcode for settings
Prefix & Suffix TABLE
HEX
HID
(SPP)
HEX
HID
(SPP)
HEX
HEX
HEX
HEX
01
CTRL A
(SOH)
19
CTRL Y
(EM)
20
SPACE
38
8
50
P
68
h
02
CTRL B
(STX)
1A
CTRL
Z(SUB)
21
!
39
9
51
Q
69
i
03
CTRL C
(ETX)
1B
ESC
(ESC)
22
"
3A
:
52
R
6A
j
04
CTRL D
(EOT)
1C
CTRL \
(FS)
23
#
3B
;
53
S
6B
k
05
CTRL E
(ENQ)
1D
CTRL ]
(GS)
24
$
3C
<
54
T
6C
l
06
CTRL F
(ACK)
1E
CTRL ^
(RS)
25
%
3D
=
55
U
6D
m
07
CTRL G
(BEL)
1F
CTRL _
(US)
26
&
3E
>
56
V
6E
n
08
Backspace
(BS)
27
'
3F
?
57
W
6F
o
09
Tab
(HT)
HEX
HID
Only
28
(
40
@
58
X
70
p
0A
CTRL J
(LF)
80
F1
29
)
41
A
59
Y
71
q
0B
CTRL K
(VT)
81
F2
2A
*
42
B
5A
Z
72
r
0C
CTRL L
(FF)
82
F3
2B
+
43
C
5B
[
73
s
0D
Enter
(CR)
83
F4
2C
,
44
D
5C
\
74
t
0E
CTRL N
(SO)
84
F5
2D
-
45
E
5D
]
75
u
0F
CTRL O
(SI)
85
F6
2E
.
46
F
5E
^
76
v
10
CTRL P
(DLE)
86
F7
2F
/
47
G
5F
_
77
w
11
CTRL Q
(DC1)
87
F8
30
0
48
H
60
`
78
x
12
CTRL R
(DC2)
88
F9
31
1
49
I
61
a
79
y
13
CTRL S
(DC3)
89
F10
32
2
4A
J
62
b
7A
z
14
CTRL T
(DC4)
8A
F11
33
3
4B
K
63
c
7B
{
15
CTRL U
(NAK)
8B
F12
34
4
4C
L
64
d
7C
|
16
CTRL V
(SYN)
35
5
4D
M
65
e
7D
}
17
CTRL W
(ETB)
36
6
4E
N
66
f
7E
~
18
CTRL X
(CAN)
37
7
4F
O
67
g
www.tec-it.com
%T%S%D
Demo
%T%S%T
Demo
.
Demo
%C%P%S
Demo
%C%S%S
Demo
0
Demo
6
Demo
C
Demo
1
Demo
7
Demo
D
Demo
2
Demo
8
Demo
E
Demo
3
Demo
9
www.tec-it.com
F
Demo
4
Demo
A
Demo
5
Demo
B
Demo
X

5
Barcode Configuration Method:
(Flow chart for setup procedure :)
Start
Configuration
End
Configuration
1D Symbologies –1
ENABLE
Matrix
2 of 5
DISABLE
ENABLE
Industrial 25
DISABLE
ENABLE
Code 39
DISABLE
ENABLE
Interleaved
2 of 5
DISABLE
1D Symbologies –2
ENABLE
EAN-8
DISABLE
ENABLE
EAN-13
DISABLE
ENABLE
ISSN
DISABLE
ENABLE
ISBN
DISABLE
ENABLE
Code 93
DISABLE
ENABLE
Codabar
DISABLE
ENABLE
GS1-Databar
(RSS)
DISABLE
ENABLE
UPC-E
DISABLE
ENABLE
UPC-A
DISABLE
1D Symbologies –3
ENABLE
GS1-128
UCC/EAN-128
DISABLE
ENABLE
MSI
DISABLE
2D Symbologies
ENABLE
Data
Matrix
DISABLE
ENABLE
QR Code
DISABLE
ENABLE
Micro
QR Code
DISABLE
ENABLE
PDF 417
DISABLE
Information in this document is subject to change without notice.
For more information, please visit:
www.riotec.com.tw
R_180807_01
0006010
0006000
0406020
0406010
0417020
0417010
0408020
0408010
0405020
0405010
0401020
0401010
0402020
0402010
0421020
0421010
0416020
0416010
0410020
0410010
0409020
0409010
0413020
0413010
0403020
0403010
0404020
0404010
0412020
0412010
0420020
0420010
0504020
0504010
0502020
0502010
0502110
0502100
0501020
0501010