RIOTEC RIOSCAN iCR6307AS User manual

1
RIOSCAN CCD barcode scanner
Quick Guide
M o d e l n o . :
iCR630 7 A S
Introduction
Designed primarily for smartphone, the iCR6307AS is a CCD
barcode scanner that allows you to scan various barcoded
items and send data to smartphone.
Its in-built excellent CCD engine allows you to reliably read
1D barcodes on various shapes and is a great space-saver
for busy or limited workspaces.
It supports not only iOS devices through Bluetooth
communication, but also Android OTG devices through USB
cable
Delivery content
*Bluetooth Barcode scanner x 1
*Charging cradle x 1
*PCB material board+3 screws x 1
*Holder for smartphone x 1
*USB cable x 1
*Quick instructions x 1
Limited Warranty
Riotec provides a one year limited warranty.
This warranty does not cover any product which has been
subject to improper use, neglect or unauthorized repair or
installation.
This warranty does not cover consumable parts.
(Cables & batteries are consumables.)
Safety instructions
*Don’t put scanner in places excessively high temperatures,
such as expose under direct sunlight
*Don’t use scanner in extremely humid area or drastic
temperature change
*The rechargeable battery is permanently built into the
product and cannot be replaced.
*Never damage the rechargeable battery. Damaging the
casing of the rechargeable battery might cause an explosion
or a fire!
Charging:
1. Switch on and charge the scanner for 3~4 hours before first usage as shown
on Fig.2. Please shift the switch of the scanner to C mode (Charging mode)
to charge.
2. The On and Off switch is located at the bottom of the handle. You may use a
fine and thin stick, then carefully press into it until you hear a low clicking
sound.
3. When you want to charge the smartphone & scanner, please use
smartphone original USB power adapter.
4. The cradle functions as a charger for the scanner. Even if the scanner’s
battery is full, the cradle will continue to supply power to the scanner. We
suggest removing the scanner from the cradle when fully charged.
5. When you charge the scanner with the smartphone, please enter Wired OTG
mode & switch to “C- Charging mode”.
iCR6307AS supports BT communication mode (for iOS and Android) and Wired
OTG communication mode (For Android OTG devices only/ For wired mode, you
must shift the scanner’s switch to “O”; followed by scanning the code of Wired OTG
communication mode if you are shifting back from BT).
*Scan the following codes to switch in between the modes. It is crucial to scan the
Clean memory data code on (Page 4, 3rd column) before switching from
Bluetooth Communication to Wired OTG communication.
Demo
%W%L%T
Bluetooth BT communication
Demo
%W%I%R
Wired OTG communication mode
(default)

2
Operating elements
*Please switch ON and charge scanner for 3~4 hours at first
time before use.
How to Connect to Smartphone via BT
1. Make sure the default is BT mode (Page 1 at the bottom of
3rd column) & your device has BT HID or SPP profile.
2. Scan the code of Bluetooth communication mode.
3. Turn off Power-Saving mode on your smartphone/tablet
4. Then, choose HID or SPP profile and scan the following 2
settings codes before connecting to smartphone/tablet.
(Either A1 A2 or B1 B2)
If you don’t know which profile to choose for your device, try
HID first, then, SPP (SPP requires a specific driver).
HID profile
SPP profile
A1
Demo
%H%I%D
B1
Demo
.
A2
Demo
%B%R%C
B2
Demo
%B%R%C
1. Click on “Settings”
2. Click on “General”
3. Click on “Bluetooth”
4. Turn it ON, and search the
Devices
5. Select “Rxxxxxx” to connect
6. When it shows “Connected”
means connection is ready.
(example: pairing with iPhone)
5. Please complete the connection procedures as the above image.
6. After the devices are paired, the screen will show “Connected”
beside the Bluetooth device that appears with an “R” followed by a
series of alpha numerical number, and usually with a “Keyboard”
icon.
7. Before using WordPad file or an appropriate APP, please set
keyboard language of the device to US English. You may proceed
to scan the barcodes and the barcode encrypted data will show on
the cursor side. If the data cannot be transferred to the
smartphone/tablet, please scan the “Reset Configuration to
Defaults” setting codes (Page 3, column 1).
Notes 1:
*This product complies with Bluetooth standards. This device used
with this product must support the same SPP or HID standard. For
Bluetooth devices with other profiles we cannot guarantee a
connection before the product has been tested.
*The communication speed and range of the product may vary due to
obstacles and radio interference between the product and device.
Condition on the host device may also effect the communication
speed and range of the scanner
Note 2:
*When the battery power is too low, the Orange LED will flash
and beep once. Scanner should be charged immediately. If
scanner shuts down it is recommended to charge it fully then
power it back on.
Trigger / Power ON
Button
(For iOS Device ONLY)
Press the trigger for 4~5
seconds to raise and lower
soft-Keyboard
Exit
Window
Micro USB port (OTG)
Use Micro USB cable to
connect to smartphone.
Charging
cradle
Indicator
(LED)
Before entering BT mode, you
must switch to right “C”
(Charging mode) first.
Then, cradle can supply
power to iOS / Android device
(through micro USB cable) &
scanner simultaneously.
Indicator (LED)
Please check the “LED
Indicator Information”

3
Reset Configuration to Defaults
(scan from A1 to A8 for HID profile or B1 to B8 for SPP profile)
HID profile
SPP profile
A1
Demo
W010F01
B1
Demo
W010F01
A2
Demo
WFFD980
B2
Demo
WFFD980
A3
Demo
W100900
B3
Demo
W100900
A4
Demo
WFFD9C3
B4
www.tec-it.com
WFFD9C4
A5
Demo
WFF115D
B5
Demo
WFF115D
A6
Demo
W047400
B6
Demo
W047400
A7
Demo
W010F00
B7
Demo
W010F00
A8
Demo
%D%F%T
B8
Demo
%D%F%T
How to Connect to Smartphone via OTG cable
1. Make sure you scan the barcode for WIRED OTG
communication mode (Page 1, at the bottom of 3rd column),
and that your Android device supports OTG functionality.
2. The Scanner must be in ”O” (OPERATION MODE) (see below)
3. Connect the scanner to Android device through micro USB cable.
4. If the scanner had been connected through Bluetooth and entered
to Data Storage Mode, make sure to scan on the Clean memory
data code (Page 4, 3rd Column) in order to change from Bluetooth to
wired connection.
5. Open the smartphone or mobile device App, so the scanned data
can be sent to the App directly, and you are set to go.
LED Indicator Information
Orange LED ON
Full charged
Orange LED Flashing
Charging / Low battery
Red LED ON
Offline / out of service
Green LED ON
Good read
Orange LED ON
Good read (Batch mode)
After the scanner connects to your iOS device and is inserted into
cradle, it may display the above message.
If this happens, remove and reinsert device into cradle.
Keyboard Country
(Wired OTG mode only)
Scan the appropriate country code as below to program the
keyboard layout for your country or language. As a general
rule, the following characters are supported, but need special
care for countries other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~
Demo
%+-$.00
Demo
%+-$.06
USA
(Original setting)
Italian
Demo
%+-$.01
Demo
%+-$.07
Norway
France
Demo
%+-$.02
www.tec-it.com
%+-$.08
Germany
Vietnam
Demo
%+-$.03
Demo
%+-$.09
Sweden
Spain
Demo
%+-$.04
Demo
%+-$.10
Denmark
Portugal
Demo
%+-$.05
Demo
%+-$.11
Switzerland
Hungary
Switch to left:
“O” (Operation mode)
(data transmission)
Switch to right:
“C” (Charging mode)
Indicator (LED)
Please check the
“LED Indicator
Information”

4
1. Place the mobile device holder by having the side of open and
close red switch on the right side of the scanner as presented on
the above image.
2. CAUTION: Please do not pull or press on any of the 4 extensions
or legs of the holder, for it can unbalance and disrupt the normal
function of the holder’s 4 extensions.
3. Place the mobile device holder lightly on the top of the base, so
the 4 elevated studs fit into the 4 holes of the holder.
4. Press the holder to the scanner firmly and draw back very
carefully until you hear a low clicking sound.
5. To separate the holder from the scanner: Press on the holder
towards the scanner firmly, then push it forward carefully.
6. IMPORTANT: We do not recommend the repetitive action of
detaching and reattaching the holder.
7. Place the smartphone onto holder (Recommendation: use
mobile device less than 14.5 cm in length), plug the micro usb to
the mobile device, then close in the extensions.
8. Push in the tiny rectangular switch at the bottom of the handle,
then switch the scanner to Operation mode, now it can scan
directly to the mobile’s APP. The user may choose to connect
through Bluetooth as well (Please review the different ways of
connection at page 2 and 3, for a more detail explanation).
There are two operating modes on the scanner
1.Data Transmission mode(Default)
Demo
%M%A%F
It is a necessary to scan “clean memory data”when
switching between these two modes.
Within Bluetooth radio range
Beyond Bluetooth radio range
Data
read
Transmit data to
smartphone/tablet directly
Save data in scanner’s memory,
scanner will transmit data to
smartphone/tablet automatically
after getting back to Bluetooth
radio range.
Enter Data Storage mode
LED
Green/ Orange LED flashes,
followed by 3 beeps.
2. Data Storage mode(Batch Mode)
Demo
%M%A%N
It is a necessary to scan “clean memory data”when
switching between these two modes.
Data
read
Save data directly to scanner’s memory. It will transmit data to
smartphone/tablet after you scan the Transmit memory data
code. To delete data, please scan the Clean memory data code.
Enter Data Transmission mode
LED
Green/ Orange LED flashes followed by 3 beeps.
Always Clean memory data before switching to Data Transmission
Mode.
Otherwise Red/ Orange LED will flash with one long beep sounds
and will not switch modes.
A. Data Transmission mode
(Default)
1. When you are out of BT signal range,
the data you scan will be saved to
memory. Once you are back within
range, the data will be sent to
smartphone/tablet automatically.
B. Data Storage mode(Batch mode)
1. Data Storage mode (Batch mode):
When you scan the barcodes, the data
will be saved directly to scanner’s
memory. After you scan the
“Transmit memory data” code
(above right), the data will be sent to
smartphone/tablet.
2. Before you can continue to scan or
switch modes, you must first delete
the data stored in the memory. To do
this, scan the “Clean memory data”
code. (below right)
Demo
%R%E%C
Transmit memory data
Green/Orange LED flashes
followed by 3 beeps
The barcode data which is stored
in the memory will be sent to
smartphone/tablet directly.
(under Batch mode, within
Bluetooth service range)
Demo
%E%R%A
Clean memory data
Green/Orange LED flashes
followed by 3 beeps.
The barcode data which is stored
in the memory will be deleted. You
can then switch modes.
Holder’s back with 4 holes to fit on
and lock up with the 4 studs the
scanner.
4 Elevated Studs to fit into the
4 holes of the Holder’s back.
Holder’s front side: Make sure the red switch is on the right
side (exactly as the above picture shows), when fitting the 4
holes of the holder to the 4 studs of the scanner
1. Holder’s front side: Shift
and Hold the red switch to
Open while you rotate the
wheel either way, in order to
shrink or spread the 4
extensions.
2. Do not pull or push the 4
extensions, nor extend the
wheel across the limit, for it
can disrupt the balance and
functionality of the holder.
3. Use mobile device less
than 14.5 cm in length.

5
Transmission Speed
Transmission speed is dependent on your device. In order not to lose
data, please choose the correct speed. Middle-speed is the Default.
Demo
%B%T%H
Demo
.
High-speed
Ultra Slow-speed
Transmission
1transmission
Demo
.
Demo
.
Middle-speed
Ultra Slow-speed
Transmission
(Default)
2transmission
Demo
%B%T%L
Demo
.
Slow-speed
Ultra Slow-speed
Transmission
3transmission
Power-saving Mode
Demo
%P%D%T00
Power-saving mode OFF
Demo
%P%D%T01
Power-saving mode ON (Default):
Enter power-saving mode after one
minute inactivity. This function
conserves battery power. When you
press the "SCAN/Power ON" button, it
will wake up and begin to scan.
*When charging, the scanner will not enter power-saving mode
automatically.
Battery information
Demo
.
When you scan this setting
code, scanner will output the battery
information to device.
Demo
.
Output battery information
automatically –Enable
Will send data to device
every 30 seconds.
Demo
.
Output battery information
automatically –Disable.
The output format of battery information is as below:
For example: %^4^%
%^NUMBER^% Number is from 0~4.
4 means 80%~100%
3 means 55%~80%
2 means 30%~55%
1 means 10%~30%
0 means under 10% -- When output reads “0”, it means low
battery power and device should be charged immediately.
Barcode Configuration Method:
(Flow chart for setup procedure :)
Start
Configuration
End
Configuration
Demo
W010F01
Demo
W010F00
1D Symbologies –1
ENABLE
ISSN
DISABLE
Demo
.
Demo
.
ENABLE
ISBN
DISABLE
Demo
.
Demo
.
ENABLE
Interleaved
25
DISABLE
Demo
.
Demo
.
ENABLE
Matrix 25
DISABLE
www.tec-it.com
.
Demo
.

6
Barcode Configuration Method:
(Flow chart for setup procedure :)
Start
Configuration
End
Configuration
Demo
W010F01
Demo
W010F00
1D Symbologies –2
ENABLE
GS1-Databar
(RSS)
DISABLE
w w w .tec-it.com
.
Demo
.
ENABLE
GS1-Databar
(RSS-Limited)
DISABLE
Demo
.
Demo
.
ENABLE
GS1-Databar
(RSS-Expand)
DISABLE
Demo
.
Demo
.
ENABLE
CODE 93
DISABLE
Demo
.
Demo
.
1D Symbologies –3
ENABLE
Industrial 25
DISABLE
Demo
.
Demo
.
ENABLE
Plessey
DISABLE
Demo
.
Demo
.
ENABLE
MSI-
Plessey
DISABLE
Demo
.
Demo
.
ENABLE
GS1-128
UCC/EAN-128
DISABLE
Demo
.
Demo
.
ENABLE
CODE 11
DISABLE
Demo
.
Demo
.
ENABLE
CODABAR
DISABLE
www.tec-it.com
.
Demo
.
ENABLE
CODE 39
DISABLE
Demo
.
Demo
.
1D Symbologies –4
ENABLE
EAN-8
DISABLE
Demo
.
Demo
.
ENABLE
EAN-13
DISABLE
Demo
.
www.tec-it.com
.
ENABLE
UPC-E
DISABLE
Demo
.
Demo
.
ENABLE
UPC-A
DISABLE
Demo
.
Demo
.
ENABLE
CODE 39
FULL ASCII
DISABLE
Demo
.
Demo
.
ENABLE
CODE 39
Transmit
Start/Stop
Character
DISABLE
Demo
.
Demo
.
Quick guide is subject to change without notice.
R_180808_01