ritetemp 8030C User manual

Operation 8030C
Made in China
Customer Support: 888-515-2585 or Visit our webiste w ww.ritetemp-thermostats.com
401-011
RESET
MENU
PROGRAM
NOTE: Your thermostat comes from the factory calibrated to+ or - 1oF actual
temperature. It is an accurate instrument. If you want your thermostat to display
the same temperature as another thermometer in your home, you can adjust its
calibration.
To change the calibration:
The unit must be in the HEAT or COOL mode.
Press the MENU button.
Press the Temp Up/Temp Down arrows to adjust the temperaturereading.
CALIBRATE DISPLAY ONwill appear.
Press HOME to save the new setting.
Calibration
RESET
MENU
PROGRAM
CALIBRATE DISPLAY -T FACTOR

Statement of use: The GPMG8030C can be used with
most 24 volt gas, oil or electric heating and air conditioning
systems, single-stage heat pumps or gas millivolt heating
systems.It cannot be used with 120 volt heating
systems or multistage heat pumps.
Operation 8030C
Using a TOUCH SCREEN
Reset
button
Menu
button
Program
button
Mode
Switch
Fan
Switch
Day
Time
of day
Time
Slot
Current
Room
Temperature
Touch Screen
Thermostat
Mode
Thermostat
Mode
Target
Temperature
PG 2
PG 1
RESET
MENU
PROGRAM
Day
Time of day
Touch here
to change
from 12 to 24hr
clock display.
Time
Slot
Current Room
Temperature
Chirp indicator
Target
Temperature
Please take a moment to try out
your touch screen itself.
To select a function on the
touch screen, place your finger
on the main temp display and
give a short firm push. Try a "tap"
of the finger or stylus. Your input
must last long enough for the
system to determine it is not an
accidental 'bump'.
Using the stylus is more
comfortable for some users.
Again allow the system enough
time to recognize your inputs.
When you are comfortable with
touch inputs, proceed.
Basic Screens
The MODE SWITCH of the 8030C must be in the HEAT or the COOL position
to access all control functions. The 8030C Thermostat has 3 basic screens.
The HOME screen is displayed when unit is operating your system.
Touching the will always return you to this screen.
HOME screen

PG3
PG4
Set Day
Touch this area to set
the day of the week.
Set Time
Touch this area to set
the time of day.
Left arrow goes back,
right arrow goes forward.
Calibration indicator
This comes on if you
have altered the
calibration of your unit
Calibration
Use this to calibrate your LCD
display to match another
thermometer.
Set
o
C -
o
F
Touch this to
set temperature
display.
Lock Program
Touch for 5 sec
to lock or unlock
Filter Timer set
Chirp set
Touch this to turn the
audible chirp on or off.
Temperature Swing
set
Return
HOME
Set Program Day
Touch this area to set
the day of the week you
want to program Target
Temps for.
Set Time Slot
Touch this area to set
the Time Slot you
want to program.
Set Program Time
Touch this area to set the
time of day you want each
time period to start.
Left arrow goes back,
right arrow goes forward.
Copy
Touch this area to copy
current program to the
next day Temp Up / Temp Down
arrows. Touch these to
raise and lower
each Target Temp.
Review
touch this area to auto cycle
through your program
Return HOME
When programming
is complete touch this
to run your program.
Displayed when the MENU button is pressed from the HOME screen.
Displayed when the PROGRAM button is pressed from the HOME
MENU screen
PROGRAM screen
1
2
3
CALIBRATE DISPLAY -T FACTOR

1 Configure
2 Auto-run
Press MENU to configure the thermostat(from HOME screen).
Set day of the week-
Touch theDay of the weekarea to cycle through
the days of the week to select the current day.
Set time of day-
Touch theTime of Dayarrows to move the time
selection forward or backward until it displays the
current time. Touch and hold for faster setting.
Set
o
C -
o
F display
Touch the
o
F and it will toggle to
o
C.
Set audible chirp-
Touch the the musical note icon to select the chirp
or no chirp.
Return HOME by touching the home icon.
This Thermostat comes preprogrammed with an Energy-
StarTM approved program. This program is recommended by
the EPA for energy efficiency.
We strongly recommend that you Auto-Run this program for oneweek, and
see if it works for you. If it does not fit your needs you can always input a
custom program.
To Auto-Run the Energy-StarTM program, select HEAT or COOL with the
mode switch. The unit is now running the Energy-StarTM program.
The clock is displayed on the left. The ambient temperature is displayed in
the the center of the LCD touch screen. The TIME SLOT icon indicates the
TIME SLOT active in the Energy-StarTm program.
The programmed temperature is shown on the lower right. For program
details refer to the Energy-StarTM program chart below.
PG 5
PG 6
All Days  70
o
F  62
o
F   70
o
F   62
o
F
MORN
6:00am
HEAT DAY
8:00am EVEN
6:00pm NITE 10:00pm All Days  78
o
F     85
o
F   78
o
F
MORN
6:00am
COOL DAY
8:00am EVEN
6:00pm NITE 10:00pm
ForwardBackward

3 Program
3 Program cont.
NOTE:60 Second Rule-Duringprogramming, if a button is not pushed in
60 seconds, the unit will return to the home screen. Everything you have
changed while programming will automatically be saved.
PG 7
PG 8
Press PROGRAM to go to the programming screen.
Select HEAT with the HEAT/Cool MODE
switch.
Select the dayyou want to program-
Touch theDay of the weekarea to cycle through
the days of the week to select the desired day.
Select the time slot you want to program-
Touch theTime slotarea to cycle through the 4
time slots, until it displays the desired time slot.
Select the time of day-
Touch theTime of Dayarrows to move the time
selection forward or backward until it displays the
desired time.
ForwardBackward
Select the desired temperature-
Touch theUP temp / Down temparrows.
Repeat the above procedures for each day of the week and
each time slot of the day as desired.
To REVIEWyour program touchREVIEW.Each time slot for each day
or set of identical days, will be displayed every 3 seconds.
Return HOME by touching the home icon.
To COPY the program from the current day to another day-
TouchCOPYon the program screen. The current day will remain solid,
the destination day will flash.
Touch the day area to advance the day and select a copy destination.
Touch COPY again to copy all settings to the destination day.
To program for cooling -
Select COOL with the Heat/Cool MODE switch and repeat the above
procedure.

Manual cont.
Manual
TEMPORARY Overide -
At the Manual override screen, Touch theTemp Up / Temp Down
arrows to select your desired temporary Target Temperature.
Touch HOME to return to operation.
The TEMPORARY icon will go on indicating you have modified the
Target Temp for the current Time Slot only(see PG7-Time Slot).
The 8030C has 3 manual override commands. These are accessed by
touching the Current Temp Display at the HOME screen (center of screen).
PG 9
PG 10
Target Temperature
HOLD
Touch this area to set
a comfortable target
temp for the system
to hold until you return
and remove HOLD.
Return HOME
Temp Up / Temp Downarrows
Touch these to raise and lower
the manual override Target Temp.
Manual Override indicator
Shows you have temporarily
modified the Target Temp.
MANUAL Temporary Override screen
HOLD -
At the Manual override screen, Touch HOLD to initiate a hold
temperature.
Touch theTemp Up / Temp Downarrows to select your hold
temperature.
Touch HOME to return to operation.
The HOLD ON icon will flash indicating you have changed the
Target Temp.
The system will HOLD this temperature until you return to this screen
and de-select HOLD, by touching the HOLD icon again.
The Mode Switch must be in
HEATor COOLmode to override.
TEMPORARY

4 Special Features
4 Spec. Featr. cont.
Swing
Swing setting determines the temperature difference from
ON to OFF that the thermostat will command the HVAC system to run.
With the MODE switch in HEAT or COOL, press theMENU button.
Touch the SWING icon and the current setting of temp
swing is shown on the display (default at 3 ).
To change the swing, touch the left or right arrows.
The furnace will cycle more at the lower numbers as it
tries to keep your set point constant.
Filter
The 8030C has a feature that keeps track of actual furnace run time and
reminds you to periodically replace your system's air filter.
Press MENU (from HOME screen) and touch FILTER icon.
This will display your accumulated filter run time.
To input a new filter life time, touch theFILTER icon for 3 seconds.
Input the lifetime hours for your new filter.
To zero the filter timer for a new filter, touch the
accumulated time display.
To leave the filter display, touchHOME
Lock
Allows you to to prevent any changes in custom settings.
To lock, touch the LOCK icon on the MENU screen for 5 sec.
To unlock, Touch the locked icon for 5 sec.
Low Battery
When the batteries are low, the battery icon will come on and flash.
The two AA Batteries in the unit need to be replaced. In some installations
your heater system will stop functioning when the thermostatloses power.
Replace batteries as soon as you see this warning.The thermostat
programs will remain for 30 seconds while the batteries arechanged.
Do not take longer than 30 secto change the batteries in your unit or
you will lose all custom settings and all programming. Onlythe Energy-
StarTM program will remain. Once the batteries are replaced, the system will
return to normal in 2 seconds.
12/24 hour
The thermostat can display time in 12 or 24 hour formats. Atthe
HOME screen touch the time display to toggle from 12 to 24 hr display.
PG 11
PG 12