Riverside Furniture Placid Cove Entertainment Hutch 16742 User manual

Riverside
FURNITURE
email: [email protected]
Made in Viet Nam
Page 1 of 4
Hutch
#16742
Placid Cove
Entertainment Hutch
Assembly Instructions
1 pc. 1 pc. right
1 pc. left 3 pcs. 2 pcs.
1 pc. 12 pcs.29 pcs. 29 pcs.12 pcs.19 pcs.
(G)
2 pcs.
Be sure to check all packing material carefully for small
parts, which may have come loose inside the carton during
shipment. Separate, count and check all parts against the
Components and Hardware List above. Failure to use the
correct length bolts in the proper locations may result in an unsafe
product and could also cause damage to the parts being assembled.
8 pcs.
2 pcs.
(F)
Left
Right
ASSEMBLY PROCEDURE:
1. Place the Top Assembly (A) on its back, on a soft
and smooth surface.
2. Assemble Cleat (D) to the Top Assembly by using
Bolt (G) Spring Washer (I) & Flat Washer (H) as
shown in DETAIL A. Tighten with Allen Wrench (J).
Assemble the Front Rail (E) to the bottom of the Top
Assembly using the 1/4" Bolts (O), Spring Washers (P)
and Flat Wahers (Q). DO NOT FULLY TIGHTEN UNTIL the end of step 4.
3. Assemble the Left & Right Back Panels to the Center Back Panel with the Bolts (F), Spring Washers (I) and Flat Washers (H),
Flush the ends of the panels and tighten with the Allen Wrench. Attach the Metal Plates (M) to the bottom back edge of the
Back Panels using the Wood Screws (N) and your Phillips Screwdriver, as shown in Detail B.
5 pcs. 5 pcs.
5 pcs.
1 pc.

(J)
(K)
DETAIL C
(J)
Riverside
FURNITURE
email: [email protected]
Made in Viet Nam
Page 2 of 4
Hutch
#16742
Placid Cove
Entertainment Hutch
Assembly Instructions
5. Using two people, carefully turn the assembled Hutch upright.
6. If using the Piers, then remove the side moulding by sliding them towards the back of the Hutch as shown in DETAIL D.
DETAIL D
4. Place the Top Assembly upside down, on its top. Carefully assemble the Left and Right
Side Panels to the Front Rail (E) and to the Top Assembly. Attach at the ends through the
Cleats using the Bolts (G) Spring Washers (I) & Flat Washers (H) and at the ends of the
Front Rail using the Bolts (O), Spring Washers (P) and Flat Washers (Q), as shown in
DETAIL C. Tighten with Allen Wrench (J). Insert the Plastic Caps (K) over the Bolts going
through the Cleats.
(Q)
5. Carefully assemble the Back Panels to the Top Assembly and Side Panels as shown in DETAIL D using Bolts (F) and
Spring Washers (I) and Flat Washers (H). Tighten all Bolts with the Allen Wrench (J).

Riverside
FURNITURE
email: [email protected]
Made in Viet Nam
Page 3 of 4
Be sure to check all packing material carefully for small parts,
which may have come loose inside the carton during shipment.
Item #16740/#16742
#16748/#16749
Placid Cove Entertainment
Assembly Instructions
ASSEMBLY PROCEDURE:
1. Carefully place the Hutch onto the top of the TV Console, as shown in DETAIL A.
2. Using the Metal Plates (L), Screws (M) and your Phillips Screwdriver, attach the Hutch to the top of the TV Console.
3. Place the Left Pier & Right Pier on the two sides of the TV Console.
4. After moving the Console and Pier cabinet together, connect units together using the Connector Bolts through the
holes in the sides as shown in DETAIL C.
If no Piers are being used, then install the Wood Plug into the holes on the outside of the TV Console.
16742 Hutch 16740 TV Console 16748/16749 Pier L&R
1 PC. 1 PC. 2 PCS.