Robern CRAFT Series User manual

Part no. 209-1416 07/21/2021
Craft Series & Curated Bath Vanity1
© 2021 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
CRAFT SERIES VANITIES
CURATED BATH SERIES VANITIES
Important safety instructions - Save these instructions
Parts - 2
Position the Vanity - 3
Level the Vanity - 3
Secure the Vanity - 4
Drawer Removal / Installation - 5
Drawer Divider Installation - 5
Drawer Adjustment - 6
Helden Installation Instructions - 7
Care and Maintenance - 12
Warranty - 12
This instruction manual contains information on how to install a Craft Series or Curated Bath Vanity. This series comes in various sizes.
These vanities need special site preparation. Do not install vanities until all framing and plumbing rough-ins have been completed and
the wall surface has been nished. We recommend using the services of a professional installer. Observe all local building codes.
Save these instructions for future use and reference. An improper installation voids the warranty. Installed vanities cannot be returned.
If you experience any problems with your Robern product, contact your dealer or Robern directly.
CONTENTS
GENERAL INFORMATION
NOTES
NOTICE: Consult professional help if you are not familiar with installing bathroom cabinetry and working with associated plumbing
hardware and tools. After safely unpacking the vanity and hardware, make sure all parts are present. If any part is missing and/or
damaged, stop and do not attempt to assemble the product. If you experience any problems with your Robern product, contact your
dealer or Robern directly.
NOTICE: Risk of product damage. When moving the vanity, do not slide or side-load the legs.
• Observe all local building codes.
• The appearance of your vanity may di󰀨er from the illustrations in this guide. The instructions still apply.
TOOLS
Check the
dimensions of your
vanity before you
begin.
Scan the QR
code to find the
specification sheet
for your vanity.

Part no. 209-1416 07/21/2021
Craft Series & Curated Bath Vanity2
© 2021 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
PARTS
[216-1119] Mackey, Chestnut Hill,
Helden, Sendai, & Bergman
Top Installation Hardware Bag
[203-1336]
(4) #10 Wing Nuts
[203-1542]
(4) #10 x 1-3/4” Screws
[203-1535]
(4) Washers
[203-1533]
(2) M5 Screws
[216-1220] Bodo & Skaarsgard
Top Installation Hardware Bag
[210-1776]
(2) Mounting Bracket
[203-1532]
(2) 1/4-20 x 2” Screws
[203-1534]
(2) Wing Nuts
[216-1224] Stanwyck, Rosebrook,
Willowmere, Alisal, & Wyndale
Top Installation Hardware Bag
[203-1540]
(4) M6 Screws
[203-1541]
(4) M6 Wing Nuts
[203-1544]
(4) Washers
[203-1543]
(4) M6 x 16mm Screws
[216-1225] Claudette & Cornell
Top Installation Hardware Bag
[203-1540]
(4) M6 x 45mm Screws
[203-1541]
(4) Wing Nuts
Depending on installation not all parts will be used.
[216-1238] Willowmere & Wyndale
Shelf Pin Hardware Bag
(4) 6mm Shelf Pins
[216-1241] Mackey & Rosebrook
Shelf Pin Hardware Bag
(4) 6mm Shelf Pins

Part no. 209-1416 07/21/2021
Craft Series & Curated Bath Vanity3
© 2021 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
1
POSITION THE VANITY
BEFORE STARTING: Remove any drawers and set aside in a secure location (see page 5 for instructions).
1. Measure and mark plumbing stub out locations on the back of the vanity.
2. DRILLING FROM THE INSIDE OF THE VANITY TOWARD THE BACK, use a hole saw to cut out the marked locations.
3. Slide the vanity into place and tight against the wall.
2 & 3
LEVEL THE VANITY
1. Rotate the adjustable leveling feet under each of the vanity legs until the entire vanity is level.
2. Use a level to check front to back and left to right.
1 2

Part no. 209-1416 07/21/2021
Craft Series & Curated Bath Vanity4
© 2021 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
SECURE THE VANITY
1. Mark the locations of the studs on top-most back rail of the vanity.
2. Using a drill bit, drill two pilot holes through the back rail and into the nished wall and stud.
3. Secure the vanity to the wall with two screws* and washers (not provided). Shim as required to keep the vanity level.
4. Reinstall drawers (See page 5).
CAUTION: Risk of product damage. Drill pilot holes into the back rail to provide support and to prevent shifting of the vanity.
21
* Robern recommends using at least two construction screws to secure the vanity to the wall. Use screws that are long enough to pass
through the vanity back rail, the nished wall, and into the stud. Larger vanities may require more than two screws to secure to the wall.

Part no. 209-1416 07/21/2021
Craft Series & Curated Bath Vanity5
© 2021 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
DRAWER REMOVAL/INSTALLATION
Drawer Removal
1. Reach under the drawer and squeeze the orange handles of both locking devices.
2. While holding the handles, pull the drawer straight out and lift it o󰀨 the runners.
Drawer Installation
1. Place drawer on the runners (either extended or retracted) and close.
2. The locking devices will automatically engage with the runners. Open drawer completely to conrm that both locking devices have
engaged.
Removal Installation
DRAWER DIVIDER REMOVAL/INSTALLATION
These instruction steps are only applicable for vanities that ship with glass drawer dividers:
1. Align glass drawer divider with slots at the front and back of vanity drawer.
2. Firmly and evenly press down on the glass drawer divider until it is all the way down and touching the base of the drawer.
1