Robinsons Rosette DWARF User manual

NOMINAL SIZE A (mm) B (mm)
10 x 8
3210 2610
10 x 10 3230
10 x 12 3850
10 x 6 1990
NOMINAL SIZE A (mm) B (mm)
6ft extension
-
1860
8ft extension 2480
10ft extension 3100
12ft extension 3720

2
Thank you for purchasing your new Robinsons greenhouse. We recommend you familiarise yourself with the instructions and read all safety
information before you commence assembly. This instruction manual is also available online at www.robinsonsgreenhouses.co.uk
in our technical help section should you need to reprint it. Should you require any additional advice you can always call us on 01782 385409.
These instructions are divided into sections highlighted by a white number/letter on a black background at the bottom corner of most pages (see opposite
page for details); part lists, B-base, P-preparation, 1-sides, 2-front gable, 3-rear, 4-joining the four sides together, 5-roof, 6-vent, 7-door, 8-glazing, 9-vent
attachment, 10-door attachment, 11 anchoring down, 12 optional louvre, 13 optional shelf, 14 optional staging. If you need to contact us for assistance
please refer to the relevant section/s. If your building is longer than 12’, i.e. has an extension then please also refer the separate extension manual.
Safety Warning
 Glass and aluminium can potentially cause injury. Please ensure you wear protective goggles, gloves, headgear and suitable footwear when
assembling and glazing the building.
 Please remember that glass is fragile and should be handled with extreme care. Always clear up and dispose of any breakages immediately.
 Do not assemble the greenhouse in high winds.
 For safety reasons and ease of assembly, we recommend that this greenhouse is assembled by a minimum of two people.
 Please clear all lying snow from the greenhouse roof as it can cause the roof to buckle or collapse.
Site Preparation
 When selecting a site for your greenhouse, it is vital that you choose as flat and level an area as possible.
 A concrete or slabbed base will provide the most solid foundation for your greenhouse.
 IMPORTANT: Do not fix your building down until the building is fully assembled, including glazing.
 Avoid placing your greenhouse under trees or in other vulnerable locations.
 To minimise the risk of wind damage, try to select as sheltered a site as possible, e.g. beside a hedgerow or garden fence.
Additional Considerations
 Please bear in mind that assembling your greenhouse can be time consuming. You may need to spread the construction over two or more
days. We recommend that you avoid leaving the building partially glazed. If you ever have to leave your greenhouse half assembled and not
anchored down, weigh it down with slabs or bags of sand to stop the wind moving it.
 You will find it helpful to prepare a large, clean and clear area in which to work in. A garage floor or flat lawn area is ideal.
 If you have arranged for someone to install your greenhouse for you, please check that all components are included. Most parts are numbered
and can be identified by a stamped number (without the ’D’) or removable label. Alternatively, the components can be identified by lengths
detailed in the packing list (see diagram below).
 Anchoring down your greenhouse should be the final stage of construction (including glazing).
 Once installed your greenhouse requires little maintenance, but to maintain the smooth running of
your door(s) WD40 or similar can be applied to the door wheels and lower door guides.
Guarantee
 Your new Robinsons greenhouse is guaranteed for 10 years against faulty manufacture of the frame-
work. This does not include glazing, moving parts, accidental damage or wind damage.
KEY
SYMBOL KEY DESCRIPTION
EXTERNAL VIEW
THINK
THIS SECTION
RELATES TO
ANOTHER
(e.g. 1 to 5)
CORRECT
DO NOT FIX DOWN!
TWIST TO LOCK
TIGHTEN
PUSH AND HOLD
CUT TO LENGTH
INTERNAL VIEW
639mm D866

3
SECTION
No TITLE ASSEMBLY SYNOPSIS: IMPORTANT INFORMATION / CONSIDERATIONS
PARTS LIST Most components should have a ‘D’ code punched into their metal surface. Identify and sepa- rate all like for like components prior to assembly. The ‘parts list’ also separates parts into the
various sections 1 - 12 shown below. Parts can also be identified by their profile pictures and
stated lengths etc..
B
BASE Base dimensions and recommendations. Ensure that your base is level as this will make as- sembly of the building, especially the glazing of the roof much more straight forward.
P PREPARATION Tools required. IMPORTANT: Use WD40 or similar in the glazing bar channels and insert the
black glazing rubber prior to frame assembly.
1
SIDES Take the side glazing bars ‘D609’ with the rubber inserted and the diagonal braces ‘D604’, use 10mm bolts to join them to the gutter and 15mm bolts to the cills (note how the head of
the bolt slides into each glazing bar during construction).
2 FRONT Again insuring that the gable framework is rubbered-up follow the diagrams to assemble each
end of the building. Make sure that you have inserted the extra bolts utilised in sections 4, 5
and 10. On the roof and side corner bars not every rubber channel will require rubber unless it
is to be utilised in a partition (see separate manual and section P).3 REAR
4 JOINING THE
FOUR SIDES Take the two sides (1) and both gables (2 & 3) and join them together on your base. It is a good idea to tie some ladders to the sides to support them if you do not have anyone to hold
them for you.
5 ROOF Attach ridge and then the rubbered-up roof bars ensuring that they are fully butted up to the
ridge and down onto the gutter. If you have cresting then it is a good idea to fit it before glaz-
ing, see section (15). Some tubular braces are supplied to add extra strength, they can be
fitted now or later with crop head bolts.
6a VENT Once the vent is glazed add silicone to the vent sides and top. Stand the vent/s on their hinge
(vent top) and then leave the silicone to set.
6b VENT SLAM The slam bar ‘D079’ can be moved up and down between the roof glazing bars so that it can
be butted down onto the pane of glass beneath, the autovent will be attached to it later on (9).
7 DOOR/S Construct the door using the diagrams and then leave to one side ready for attachment in
section (10).
8
GLAZING
Layout the bar cappings and covers around the building like a sundial checking that all is pre-
sent and correct. You can also place the roof cappings in the gutters so they are closer to
hand. The glass in the ends has to bevel on the black separator strip, this bevelling action
allows the glass to tuck underneath the roof corner canopy. Use the capping and the self tap-
ping screws to then hold the glass in place. The covers then enclose the screw heads giving a
neat finish.
9 VENT
ATTACHMENT Take the assembled vent and slide the vent hinge ‘D866’ into the end of the ridge allowing the vent the pivot open and closed. Vent stops go either side of the vent to stop any lateral move-
ment (so insert stop / vent / stop). Attachment of the Bayliss XL autovents.
10 DOOR
ATTACHMENT Utilise the bolts inserted in section (2) to attach the upper door track. The lower door runner ’D861’ and ramp threshold ‘D088’ push down and lock together.
11 ANCHORING
DOWN Now that the greenhouse is finished and the door and vent/s are operating without interfer- ence then you need to anchor the building down using 2” rawl plugs and screws. Use a 7mm
masonry bit in a hammer drill to create the holes.
12 OPTIONAL
LOUVRE They attach to the building during the glazing process (8) like a piece of glass with a black separator above and below them.
13
OPTIONAL
SHELVING
14
OPTIONAL
STAGING
15 FINISHING
TOUCHES Now that the main body of the structure is complete you can add; ridge caps, downpipe fit- tings, eave bungs. Images showing cresting and finial attachment, this is often easiest to do
after section (5) rather than using the vent apertures later on (i.e. before glazing).
Robinsons integral cantilever staging and shelving attaches to the inside of the greenhouse
frame using either square head bolts (insert four into each side glazing bar ’D609’ during con-
struction of the sides (1)) or rectangular ‘crop head’ bolts which can be fitted retrospectively
(both sets of bolts accompany the shelving/staging). This system allows the height of either
the staging or the shelf to be set at an operator specific height. Commonly the staging brack-
ets are set 900mm from the cills though you can alter this to suit the end user/s. The alumin-
ium shelf / staging slats come in two lengths; (4’):1240mm ‘D2002’ and (6’):1860mm ’D2003’.
These slats can combine to create any length of staging required, i.e. 4’+6’ = 10’ etc...

4
Section
Ref Part
No. Section Size (mm) 10 6 10 8 10 10 10 12 Section
Ref Part
No. Section Size (mm) 10 6 10 8 10 10 10 12
D043 1894 2
D021 2514 2
D022 3134 2
D023 3754 2
D042 1897 2
D014 2517 2
D015 3137 2
D016 3757 2
D604 1316 4
D609 1160 4 6 8 10
RUBBER 1000 (1m)
10 12 14 17
D174
N/A
4 4 8 8
D044 1897 1
D001 2517 1
D002 3137 1
D003 3757 1
D065 1744 4 6 8 10
RUBBER 1000 (1m)
21 28 35
D866 639 2 2 3 3
D863L 613 2 2 3 3
D863R 613 2 2 3 3
D862 593 2 2 3 3
D079
PLUS FLUFF
590 2 2 3 3
D114 N/A 4 4 6 6
D220
PLUS SCREW
N/A 4 4 6 6
D205 N/A 4 4 6 6
D038A 3226 1
D600 1270 1
D669L 1 1004
D669R 1 1004
D608 1160 4
D655 1906 1
D656 1610 2
D657 1314 4
D670 2210 2
D109 3140 1
D653 1270 1
D626 1497 4
D111 N/A 2
D854L
1744
2
D854R 2
RUBBER 1000 (1m)
D174
N/A

5
Section
Ref Part
No. Section Size (mm) 10 6 10 8 10 10 10 12
D090 +
D347 lock =
D301
1824 1
D092 +
D156 strike =
D303
1824 1
D093 1824 1
D094 1824 1
D096 +
D217 wheel =
D307
611 2
D095 611 2
D097 611 2
D232 905 4
D233 797 4
P053 N/A 2
D225 610 2
D840B 4000 1
1 D618 1144 4 6 8 10
2/3 D658 1314 4
3 D659 1610 2
2 D660 311 2
3 D661 1906 1
2 D662 600 1
5 D870 601 4 6 8 10
5 D876 1152 4 6 8 10
2/3 D610 1160 4
1 D620 1144 4
2 D814 1883 2
5 D871 601 4
5 D877 1152 4
2/3 D614 1162
1 D619 1144 8 10 12 14
2/3 D663 1316 4
3 D664 1610 2
3 D665 1908 1
2 D666 602 1
2 D667 313 2
5 D811 1754 8
2 D836 1883 2
4
10 12 14
Section
Ref Part
No. Section Size (mm) 10 6 10 8 10 10 10 12
D861 2450
D088 1207 1
D086 2510 1
D085 2510 1
D627 114 2
1
D163 90 2
D150 N/A 1
D154 N/A 2
D865 1210 1
D671 610 1
10mm
31 37 43 49
15mm
46 48 50 52
m6
77 85 93 101
MAIN FRAME QUANTITIES
VENTS / DOORS etc SEPERATE

6
tolerance of +/- 0mm

7
PARTITION
ONLY
REFER TO
SEPARATE
MANUAL
PARTITION
ONLY
REFER TO
SEPARATE
MANUAL
Feed glazing rubber into each glazing bar and
trim to length. Notice that some channels are
only used on a partition. Applying a lubricant to
the aluminium channels will speed up insertion.
The frame is assembled by feeding square
headed bolts, either 10mm or 15mm in length
into the slots on glazing bars and then locating
those bolts through holes in purlings and cills,
etc… Twist in (rectangular) crop headed bolts
are also used towards the end of construction
to attach components to the frame when the
glazing bar slots are no longer exposed at the
ends. 10mm
15mm

8
6
X 2
12
X 2
8
X 2
10
X 2
D042
D043
D014
D021
D015
D022
D016
D023
Part No mm Quantity
D016 3757 2
D023 3754 2
D609 1160 10
D604 1316 4
D174 8
M6-
10mm 10
M6-
15mm 14
M6-
NUT 24
12 X 2 DWARF
Rubber 1000 24
Part No mm Quantity
D015 3137 2
D022 3134 2
D609 1160 8
D604 1316 4
D174 8
M6-
10mm 8
M6-
15mm 12
M6-
NUT 20
10 X 2 DWARF
Rubber 1000 19
Part No mm Quantity
D014 2517 2
D021 2514 2
D609 1160 6
D604 1316 4
D174 4
M6-
10mm 6
M6-
15mm 10
M6-
NUT 16
8 X 2 DWARF
Rubber 1000 14
Part No mm Quantity
D042 1897 2
D043 1894 2
D609 1160 4
D604 1316 4
D174 4
M6-
10mm 4
M6-
15mm 8
M6-
NUT 12
6 X 2 DWARF
Rubber 1000 10

9
D609
D604
D609
D604
15mm
10mm
TRANSIT
BOLT ON
DIAGONALS
15mm

10
Part No mm Quantity
D600 1270 1
D608 1160 2
D626 1497 2
D657 1314 2
D669L 1004 1
D669R 1004 1
D653 1270 1
D670 2210 2
D854L 1744 1
D854R 1744 1
D600
D670 D670
D608
D608
D854R
D626
D626
D854L
Part No mm Quantity
D174 4
M6X10 8
M6X15 18
M6NUT 26
D111 1
D227 23m
+
D657
D657
D669R
D669L
D653
15mm
15mm
15mm
15mm
15mm
15mm
15mm
15mm
15mm
15mm
10mm
15mm
15mm
10mm
15mm
15mm
10mm
10mm
10mm
10mm

11
D608
D174
D111
D670
D854R D854L
D854L
D854L
D608
D626
D600
D670 D626
D670
D669L D669L
D653

12
Part No mm Quantity
D038A 3226 1
D109 3140 1
D608 1160 2
D656 1610 2
D854L 1744 1
D854R 1744 1
D626 1497 2
D657 1314 2
D655 1906 1
Part No mm Quantity
D174 4
M6X10 11
M6X15 20
M6NUT 31
D111 1
D227 24m
D038A
D656 D656
D608
D608
D854R
D626
D626
D854L
D657
D657
D109
D655
15mm
15mm
15mm
15mm
10mm
15mm
15mm
10mm
15mm
15mm
10mm
15mm
15mm
15mm
15mm
10mm
15mm
15mm
10mm
15mm
15mm
10mm
10mm
10mm
10mm

13
D111
D656
D854R D854L
D854L
D608
D038A
D174
D626
D656
D038A
D655
D854L
D608
D626
D109

14
EQUAL

15
6’
Part No mm Quantity
D044 1897 1
D065 1744 4
RUBBER 1000 14
D126 445 0
D128 1015 0
8
1 2
D065
D065
D066
8’
Part No mm Quantity
D001 2517 1
D065 1744 6
RUBBER 1000 21
D126 445 2
D128 1015 1
12 10’
Part No mm Quantity
D002 3137 1
D065 1744 8
RUBBER 1000 28
D126 445 4
D128 1015 2
16 12’
Part No mm Quantity
D003 3757 1
D065 1744 10
RUBBER 1000 35
D126 445 6
D128 1015 2
20
2 1 D065
X2
D128
D126

16
D1208
1 of -
610 x 610
pane
D866
D863R
D863L
D866 639 1
D863L 613 1
D863R 613 1
D862 593 1
Part No mm Quantity
D220
PLUS
SCREW
N/A 2
D205 N/A 2
SY-
BOLM6X11 10 4
SYNUTM6 M6 4
8 X 12 S/T
FS6017 10 2
Part No mm Quantity
8 x 19 S/T
FS6018 19 2
D863R
D866
2
2
D1208
1 of -
610 x 610
pane

17
D862 D862
D863L
2
2
2
2
2
FLIP
VIEW
D119
CUT
6mm
SILICONE

18
D114
D079
FLIP
VIEW
D079
PLUS
FLUFF
590 1
D114 N/A 2
Part No mm Quantity
SY-
BOLM6X11 10 2
SY-
BOLM6X15 15 2
SYBOLM6
X11CROP 10 2
SYNUTM6 N/A 4
Part No mm Quantity
D114

19
D1216
GLASS
D1216
GLASS
D1208
GLASS

20
D094
1824 1
D090 + D347 lock =
D301
1824 1
D092 + D156 strike =
D303
1824 1
D093
1824 1
D096 + D217 wheel =
D307
611 2
D095
611 2
D097
611 2
Part No mm Q Part No mm Q
D232 905 4
D233 797 4
P053
N/A 2
D225
610 2
D840B
4000 . 1
D263
PACK x 2
N/A 14
N/A 14
D261
PACK
N/A 24
D911
555 x 812
pane
D912
555 x 922
pane
8
D094
D233
D232
0
A
B
A
B
D095
D233
D232
D911
555 x 812
pane
D912
555 x 922
pane
D303
D301
D093
D840B
D840B
33mm
B