Robustel M1000 Pro V2 User manual

Robustel GoRugged M1000 Pro V2 Quick Guide
RT_QG_M1000 Pro V2_v.1.0.0 24.01.2014 1 / 6
Robustel GoRugged M1000 Pro V2 Quick Guide
Chapter 1. Interface Introduction
1.1 Overview
1.2 LED Indicators
After inserting the SIM card into the modem and power on, the LED indicators’status should be as follow when work
normally:
Name
Color
Status
RSSI (3 LEDs)
Green
At least two bars
NET
Red
Register to network: blinking every 3s
SYS
Green
System is running normally but without any GPRS/UMTS connection: blinking every 1s
System is running normally and GPRS/UMTS connection established: blinking every 3s
PWR
Green
On when DC power connected
Note ： Please refer to Robustel GoRugged M1000 Pro V2 User Guide to get more details about the LED indicators.

Robustel GoRugged M1000 Pro V2 Quick Guide
RT_QG_M1000 Pro V2_v.1.0.0 24.01.2014 2 / 6
1.3 Working Mode Switch
There are two working modes available in the gateway, please check carefully:
Mode
Description
Config Mode
When DIP switches to Config Mode, user could use follow functions:
1. Configure gateway via M1000 Pro V2 Configurator ;
2. Upgrade firmware.
Serial port parameters is fixed as 115200, 8, None, 1
Normal Mode
When DIP switches to Normal Mode, user could use follow functions:
1. Automatic GPRS/UMTS connection (no AT commands required);
2. Wakeup by Timing/Periodical/Call/SMS/Serial Data;
3. Transparent data communication or become a Modbus gateway;
4. CSD communication.
5. Remote configuration or firmware updating.
Serial port default parameters: 115200, 8, None, 1
1.4 PIN assignment
PIN assignment for modem’s DB9 female connector
PIN
RS232
RS485 (2-wire)
1
Data+ (A)
2
RXD ->
3
TXD <-
4
5
GND
6
Data- (B)
7
RTS <-
8
CTS ->
9
Switch

Robustel GoRugged M1000 Pro V2 Quick Guide
RT_QG_M1000 Pro V2_v.1.0.0 24.01.2014 3 / 6
1.5 Grounding the Modem
Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground
connection from the ground screw to the grounding surface prior to connecting devices.
Note: This product is intended to be mounted to a well-grounded mounting surface, such as a metal panel.
1.6 Power Supply
The power supply range is 9 to 36VDC.
Note: Please take care about the polarity, and do not make reverse connection.
Chapter 2. Hardware Installation
2.1 Insert/Remove SIM Card
SIM card is used for connecting to cellular network, you need buy SIM card from local operators.

Robustel GoRugged M1000 Pro V2 Quick Guide
RT_QG_M1000 Pro V2_v.1.0.0 24.01.2014 4 / 6
Note:
1. Don’t forget screw the cover for again-theft.
2. Don’t touch the metal surface of the SIM card in case information in the card is lost or destroyed.
3. Don’t bend or scratch your SIM card. Keep the card away from electricity and magnetism.
4. A SIM card set with PIN code cannot be used normally in the gateway without the correct PIN code.
5. Make sure to disconnect the power source from your gateway before inserting and removing your SIM card.
2.2 Connect the External Antenna (SMA Type)
Connect this to an external antenna with SMA male connector. Make sure the antenna is for the correct frequency as
your GSM operator with impedance of 50ohm, and also connector is secured tightly.
SIM 2
SIM 1

Robustel GoRugged M1000 Pro V2 Quick Guide
RT_QG_M1000 Pro V2_v.1.0.0 24.01.2014 5 / 6
2.3 Power On and Connect with PC
User can use the serial cable to connect the modem’s DB9 female connector to external controller / computer.
Chapter 3. Operate the Modem
3.1 M1000 Pro V2 Configurator Overview
M1000 Pro V2 Configurator is a PC-based configuration software tool for managing and configuring Robustel M1000
Pro V2 gateway. With a full graphics mode and Windows-based environment, even first time users will find it easy to
learn how to use this new software tool.
Note: M1000 Pro V2 Configurator can be used with Windows 2000/XP/Vista/7 32/64-bit operation systems.
3.2 Starting Modem Configurator via Serial interface
1. Switch the modem to “Config Mode”, connect the RS-232 port of the modem to a host PC, then power on the
modem.
2. Double click “Modem Configurator.exe”to start the software.

Robustel GoRugged M1000 Pro V2 Quick Guide
RT_QG_M1000 Pro V2_v.1.0.0 24.01.2014 6 / 6
3. Select correct COM port, then click button. After that you can see the popup windows “Operation
Succeed”.
Note: The RS-232 connector uses standard PINOUT. A direct male DB9 to female DB9 cable can be used to
connect to a PC’s serial port.
4. Configuring the modem via M1000 Pro V2 configurator.
Note: Please refer to Robustel GoRugged M1000 Pro V2 User Guide to get more details about M1000’configuration.